Now you stop vaping, the coil cools down a lot and its resistance value goes down to 0.40 ohm. Next time you vape, the box detect an high mismatch between the current resistance and the last read one, so it will ask if you have changed the coil.
Why does my vape taste burnt even with a new coil?
Mar 02, 2017 · I have a Kanger tech tank on top of the mod, and I've adjusted the ohms down to .500 and I am running it extremely low, at 26.0 W and now it continually keeps asking me if the "coil is new" every time it's dormant for more than a couple minutes, and I pick it up to Vape. Ugh...
Why is my vape not getting power?
Jun 28, 2017 · Thats pretty much the exact answer there - What's happening is that the mod see's a different resistance (Usually more than a 20% difference from the last reading) and is asking Did you put a new coil / atomiser on or is this just the old one that hasn't cooled down yet (Since TC relies on the change in resistance as the wire heats).
Why should I Prime my vape coils?
Mar 04, 2019 · the issue is the mod keeps asking ” New Coil (+)” or ” Old Coil (-)”, the vaping mod cannot detect the atomizer due to the short circuit of your tank or mod. How To Fix: 1. Use a pin to stick on the 510 connectors to see if it can be fixed or …
How to extend the life of your vape coils?
level 1. krawhitham. · 9 mo. ago · edited 9 mo. ago. I have the same issue with this mod, it always asks if its a new coil. The same tank and coil works great on my Aegis Legend 1, but on 2 different Aegis Legend 2 mods it asks consistently if it's a new coil. geekvape could fix this with a firmware tweet. 1. level 1. WorldlinessCertain64.
Why does my vape keep saying no coil?
If you press the firing button on your e-cig and you see the message 'no atomizer' or 'check atomizer' it means that your vape mod is not reading the coil within your vape tank properly. It can be because of the 510 connection, the vape coil itself or the bits in between.Sep 9, 2020
How long do you have to wait to vape a new coil?
around 5-10 minutesIt's always recommended to leave your coil to prime for as long as possible - anywhere between 5-30 minutes. The longer you leave it the better, but most coils should be ready to vape after around 5-10 minutes.
How do you reset the coil on Aegis legend?
5 clicks of the fire button will turn the device on and off. 3 clicks of the fire button will allow you to scroll through Output modes. Once in Output adjustment mode, you can scroll down to adjust coil resistance and reset puff count by pressing the fire button. Press and Hold Fire & + button – Brightness Up.May 21, 2021
What does New coil mean?
For example, you have been using a 0.2 ohm coil, you change it for a 0.1 ohm coil, if you say "not new coil" it will carry on with settings for a 0.2 ohm coil, if you say "new coil, it will change the settings to suit a 0.1 ohm coil.Jun 26, 2017
Why does my vape taste burnt with a new coil?
If you've just changed to a new coil and still getting a burnt taste it could be due to chain vaping, when you take puff after puff with barely any break in between. It is probably the most common cause of coil burning, especially for new vapers.Feb 13, 2022
How long should vape coils last?
between 7 to 21 daysWhile the exact duration may differ from person to person depending on their personal vaping habits, most new coils are designed to last anywhere between 7 to 21 days. This varies depending on how well you care for and clean your device.Jan 29, 2021
How do I fix my vape coil?
It's quick and easy to do:Take your new coil and apply 3-4 drops of your e-liquid directly to the wick.Set aside and wait for roughly 10 minutes.Screw the coil on to your device.Fill your tank with your chosen e-liquid and screw it on to your vape.More items...
Why is my coil not working?
Check your tank to make sure you have enough e-liquid. If your tank is completely full but you still have weak vapor, it is possible that your atomizer or coil has been flooded. If this happens, simply take your atomizer apart and clean it with a paper towel or gently blow through it to get the excess liquid out.Oct 3, 2016
How do you prime a vape coil?
0:451:52Priming a vape coil in 2 minutes - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet your either quid. And add a drop onto each of the liquid inlet holes add a few drops onto theMoreGet your either quid. And add a drop onto each of the liquid inlet holes add a few drops onto the wicking material down the middle hole put your vape coil in your tank fill your tank with the liquid.
What is mouth to lung vaping?
Mouth-to-lung is a style of vaping that is most similar to smoking. When you draw, you first pull the vapour into your mouth before then inhaling it into the lungs. This draw is more gentle than drawing on a cigarette, as the harder you draw the less vapour you get.Jun 26, 2019
What does new coil up same down?
It's simply asking if you have replaced the coil. If you have hit the up (or "+") button. If it's the same hit the down (or "-") button. Just had the same issue, spent a bit of time googling it and this answer was both simple and worked!
Do all coils fit all Vapes?
No! It would be safer to say that the opposite is true, in that most heating coils are made for specific vape brands or even specific product lines within a vape brand.
Why is my coil burning out?
Coil Burnt Issue. If the coil burnt out within a short time, follows might be the causes to the issue: 1. Did not prime the coil before vaping. 2. The e-juice you fill is not enough. 3. Improper vaping settings of power. 4.you vape too frequently. 1. Prime the coil with low wattage for the first several puffs.
How to fix 510 connectors?
How To Fix: 1. Use a pin to stick on the 510 connectors to see if it can be fixed or not. if can not work, please refer to the next step. 2. Please try other tanks or coils with your mod and try the same tank on other mods to check if they can work fine. to confirm whether the problem is in the tank or the mod. 3.
Why do you need to prim your vape coil?
Properly priming your coil can help to reduce wear and tear on your device and make sure you can enjoy a better flavor from your vape coil. Make sure that you are repeating this process every time you install a brand-new coil: Unpack your brand-new coil from the box.
What is a vape coil?
What is a Vape Pen Coil? Vape pen coils are also called atomizer coils. These are heating elements that screw directly onto the battery inside a vape pen. This heating element on board also contains a wick or filament which is commonly made out of cotton or bamboo.
Why does my atomizer burn?
This is because the wick has not had an appropriate amount of time to soak up the e juice for that hit. Instead of producing vapor, it's just producing the smoke from the coil as it dries the wick.
Why does my vape burn?
The Most Common Causes of Burnt Vape with the Wick. Vaping on high wattages: If you adjust your device to vape at an extremely high temperature, it's going to heat through the E-liquid far too fast. When the E-liquid is completely vaporized, the coils on board will start to burn the wicks. It's very important you check in on manufacturer wattage ...
Why does my vape taste burnt?
A bit of a burnt taste vape can just be an indication of a wattage issue and sometimes it can go away after a few puffs.
How long does a coil last in a vaporizer?
Here are some of the top factors that may determine when it's time to change your coil: The amount you use your vaporizer: Most of the times the coil life from the manufacturer is suggested in weeks. If you are a heavy user of a vaporizer, it can last a short amount of time.
How long to let e-liquid saturate?
Fill up the pod with the E-liquid using the dropper and then let the pod completely saturate for at least 10 min.. After the pod has been saturating with the built-in coil inside of it for 10 min., inhale a few times from the top of the pod while it isn't connected to the battery.
1. Make sure your coils are primed
A mistake new vapers tend to make is failing to prime vape coils adequately. “Priming” simply means making sure the wick is saturated correctly before you vape.
2. Ensure your tank is full
A cardinal rule for avoiding burnt hits: Ensure the two wicking ports (the tiny holes on either side of your coil) are never exposed. Failing to do this will significantly decrease your coil’s lifespan and increase the likelihood of hell being unleashed into your lungs!
4. Be careful not to chain vape
If you’ve had the chance to read any of our other blogs, you’ve probably seen “chain-vaping” pop up before. It shouldn’t come as a surprise that good ol’ human nature is one of the most common reasons for a lot of vape-related issues.
Conclusion
As you can see, though undeniably frustrating, there are quite a few reasons why your vape might taste burnt with a new coil. Fortunately, they’re often easy to fix. We’re confident that we’ve covered the ones that are likely to be causing you trouble. So follow the above steps and prevent those burnt hits from spoiling your day!
Why does my vape coil burn out?
6 Common Reasons Why Vape Coils Burn Out – and How to Avoid It! 1. Not Enough Vape Juice in the Tank. Whenever your wick is dry, it will not function properly. As mentioned, the wick needs to be saturated in vape juice. In case you vape frequently, then your tank will start to run empty and the wick will not soak up as much ...
How to avoid burnt coils in vape?
To avoid the burnt coil, keep checking your tank and top it up when it is at a third of its capacity. 2. Chain Vaping.
What happens when you vape with a wick?
This wick surrounds the element which usually heats up the moment current passes through it, causing the vape juice to evaporate. Once evaporation occurs, the vaper can inhale the vapor that’s produced. However, if the wick wasn’t primed properly before you took your first puff, you’ll experience a burnt taste.
What happens if you use a coil that isn't high grade?
If you do so with a coil that isn’t high-grade, the wick won’t be able to handle the heat these wattages will generate and will end up burning. The solution to this is to simply reduce your power setting and find out the ideal wattage you should vape at.
What happens when you vape multiple puffs?
This causes the wick to burn.
Why is it important to take care of your coil?
While preventing your from burning out seems like a lot of work, it’s worth it because it helps you avoid losses. It also saves you the trouble of experiencing an irritating burnt taste. Taking care of your coil could mean the difference between an enjoyable vaping experience or a terrible one.
Can you use a lot of sweetener in vape juice?
Using a Vape Juice with a Lot of Sweeteners. Vape juices that contain a lot of sweeteners can cause gunking up of coils. While they may be delicious, they could significantly destroy your coils. When gunking happens, the wick will be unable to soak up more juice so when you vape, the coil could get burnt.
Acer50 Super Member ECF Veteran
I do not know how many of you have bought or tried the Geek Vape Aegis the indestructible mod. I did, and yes as far as being indestructible I have found it very much so. However, it it in need of urgent firmware upgrade as its V1 firmware proved to be unsafe. The Upgrade is available on Geek Vapes website.
spolen23 Full Member
The absence of the resistance lock is a major problem. I get the new/old atomizer question dozens of times per day without even taking my addy off. It is very annoying! If the resistance changes, and it will when fired, it asks me the same question and doesn't let me fire it unless i select new or old. Locking the resistance would prevent this.
Dropmyload Super Member Verified Member ECF Veteran
I am thinking of getting one. I can see on the website resistance lock has been added. Any update from users?
EODPaul Senior Member ECF Veteran
The update works. Resistance lock, the wattage stays locked even after power off and on, the 'New coil?' prompt is improved. I don't see any improvement in battery life, but it's no worse either. I have 2 of these now, and they've officially replaced my Yihi SX Q mini as my favourite mods .
stols001 Moved On ECF Veteran
I would do the upgrade. You want to set the resistance when your coil is cold. If you've been vaping it and then remove it too quickly, your resistance will be incorrect as most wires read their resistance differently when they are hot than when they are cold. So it would be a good idea, and make things more hassle free.
Knut arne Full Member
Just got one too. The screws for the update port, what kind of screws are they? Hex or torx ? Is it mm or inches size?
Knut arne Full Member
Finally got some torx, it seems like T 6,5 would be a perfect fit, t6 is a little loose and t 7 is too big. But these i have are low quality torxs and i dont have any 6,5.
