SMOK Ohms Too High or Too Low Error messages about ohms are specifically related to the resistance of your coil (s) and indicate that a coil is not compatible with the device. Typically, pairing the proper SMOK-branded coils with your SMOK device is the easiest way to fix this problem.
Why is my vape giving me a “ohms too low” warning?
When you are vaping, it may give a "ohms too low" or "ohms too high" warning? There are two reason: (1)Normal circumstance: 1. The coil resistance is less than 0.1 ohm, or more than 3.0 ohm. (2)Abnormal circumstance: If the warning still pops out while coil resistance is reasonable, it may caused by the following reasons: 1.
Why won’t my Smok vape turn on?
If your SMOK vape isn’t turning on, it could be a quick fix: Try charging your mod to see if a dead battery is an issue. Plug it into the charger and hope that you forget to recharge after your last use. Check the battery to confirm that it’s properly inserted.
How many ohms does a smok X-Priv read?
My SMOK X-Priv will read anywhere for New/Old to .224 or .197 Ohms for a .12 Ohms Coil. I've tried to take batteries out, and lots of other choices.
Why is my atomizer shorted out on my vape?
“Short Atomizer” or “Don’t Abuse Protects” Seeing either of these SMOK error messages is a big red flag, and you should immediately stop vaping for your safety. The cause of these two messages is a short circuit in either your mod or tank, which is a serious but sometimes repairable problem.
How do you fix Smok ohms too low?
"Ohms Too Low" or "Ohms Too High"?...You could try the following methods to recover:Please take off the tank and click the fire button, and then place that tank back on, click "n" when it asks "is it a new coil".Please make sure screws are tight on the tank if you use the RBA coil on your mod.More items...
What does it mean when it says ohms too low on vape?
'Ohms too low' or 'ohms too high' error message This SMOK warning refers to the resistance of your coil. Most SMOK users will use coils that are made by SMOK so they should not have this problem. If you have a rebuildable atomizer (RBA), it could be that the coil resistance is too low or too high.
How do I reset my Smok X priv?
Hold all buttons WITHOUT batteries and plug into a USB port. Keep holding for ten seconds, throw batteries in while still connected, disonnect and reconnect to turn on.
Why is my Smok X priv not hitting?
Take the coil out and reinstall, prime, reset internal settings to new coil, etc. Coil might not be installed right enough or maybe it burnt if not primed properly first time. Charger plugged in should tell you how full batteries are… fully charge for several hours.
How do you change the ohms on a vape?
0:191:52Down the middle there a little bit on the wicking ports as well you just want to ensure that it'sMoreDown the middle there a little bit on the wicking ports as well you just want to ensure that it's nice and saturated in the coil before you start firing it up pop the coil. Into the pod.
How do you unlock a SMOK vape?
0:100:48It's pretty easy one two three clicks of the fire button fire key unlocks oh we're beeping look atMoreIt's pretty easy one two three clicks of the fire button fire key unlocks oh we're beeping look at that Nathan had we go into the lock mode again one two three fire key locked oh I can't fire oh.
Why is my SMOK vape blinking 4 times?
Resistance protection: when the atomizer resistance is lower than 0.1 ohms or higher than 2.5 ohms, the LED light will blink 4 times and the battery will automatically shut down the output.
Why is my SMOK vape blinking white?
Short circuit protection: if a load short circuit is detected, the white LED light will flash 4 times and the battery will automatically shut down the output.
IgnorantCig Super Member ECF Veteran
I don't have an X-PRIV, but I'm a pretty good googler and here's what SMOK says about that.
Zaryk Ultra Member Verified Member ECF Veteran
There is a couple reasons this can happen. First and easiest, take your tank off and double check the 510 pin on both the tank and the mod for juice. If there is juice in there, wipe it clean with a Q-tip or a paper towel. Reconnect the tank and check if it is fixed.
Zaryk Ultra Member Verified Member ECF Veteran
That's not good. Have you had any leaking issues where juice may have gotten into the mod?
MegaVaper Senior Member ECF Veteran
I would advise against trying to wash them out with water. I have one that stops working after a while because I leak juice all over it. Yes im a messy dripper.
SnapDragon NY Ultra Member ECF Veteran
And my mod will come on and everything. Just when I try and take a hit it says low ohms
SnapDragon NY Ultra Member ECF Veteran
No. The only thing I can think of is my cousin spilt water on it the other day. But its worked fine until a couple hours ago
Eskie ECF Guru Verified Member ECF Veteran
There's another thread in the VW section on the same issue Smok X-Priv resistance not changing!
Edward Denison Senior Member
I've found the solution, my X-Priv Mod stopped changing Ohms when I changed tanks, and this fix aloud me to keep my mod.
Coyote628 Ultra Member ECF Veteran
A metal coil is NOT a variable resistor. The only thing you are changing is the display on your mod.
Coyote628 Ultra Member ECF Veteran
My tpriv had that function, and i forgot some basic electronic and thought i was changing the resistance of a coil. Brainfart. A wire coil is simply not a variable resistor, no matter what the display screen says.
Zaryk Ultra Member Verified Member ECF Veteran
I've tried tanking the tank off, firing at 1W to show "No Atomizer," then put on a different tank. My 3 tanks run at .12, .15, .15 Ohms. My SMOK X-Priv will read anywhere for New/Old to .224 or .197 Ohms for a .12 Ohms Coil. I've tried to take batteries out, and lots of other choices. The way I'm doing it now I can pre adjust to my desired Ohms.
BrotherBob ECF Guru ECF Veteran
I've found the solution, my X-Priv Mod stopped changing Ohms when I changed tanks, and this fix aloud me to keep my mod.Ok so here's how to fix it.
Why is my vape not working?
If the vape appears to be on, but the display is dark, you may have accidentally activated “stealth mode.”. Quickly press the fire button three times to turn off stealth mode. If this doesn’t work, you may need to upgrade your firmware. Otherwise, the problem might be caused by screen damage or another related issue.
Why is my ohm error so high?
If you’re working with a rebuildable atomizer (RBA), the resistance of your coils may be too high or low. Adjusting the resistance will usually clear the error. Or, you may need to tighten the screws properly. Other reasons you may see an ohm error include: The resistance detection component of your device is broken.
What is the best brand of vape?
There’s no doubt that SMOK is one of the vape industry’s best brands, crafting top-of-the-line mods and pod systems like the SMOK Nord, SMOK Morph, SMOK NOVO, and so many more.
How long should I soak my SMOK coil?
Allow the coil to soak inside of the tank for about 20 minutes, then take a few dry puffs before using the fire button to begin vaping. Check your output wattage. Make sure that your mod’s output matches the recommended output wattage on the side of the SMOK coil.
How to fix a coil that tastes burnt?
Here are a few suggestions for how to fix coils that taste burnt: Replace your coils when needed. Expect to replace coils every few weeks or so (or about 50mL of e-juice, according to SMOK guidelines). Burnt-tasting coils are usually the first sign that it’s time to switch them out for new ones.
Can you fix a dead vape mod?
Luckily, as just about any seasoned vaper will tell you, problems with a vape mod are often very easy to fix, being forced to replace a dead mod is a pretty rare occurrence. Often, a seemingly serious mod issue is simply the result of user error and can be resolved in next to no time.