The new Iolite Vapor Optimizer is designed to enhance vapor density by adding three additional heat pins to the heating chamber. This tool allows the heat to distribute more effectively in the bowl, providing more efficient and even vaporization. The optimizer does a great job of boosting the Iolite’s performance.
What is an atomizer in vaping?
One of the most widely used terms in vaping is the atomizer. This is a component that makes up a vape or e cigarette. The atomizer is a crucial piece of a vaporizer and without this component almost no vaporizer would work.
What to do if your vape says atomizer short?
If using an RDA/ RTA, check and see if the coil is touching the cap or deck. If error messages continue to pop up, use a different atomizer on the mod. If it still reads “atomizer short,” the problem is with the vape, not the atomizer or coil.
What makes a good atomizer different?
The second differentiating factor is how the atomizer is built. Essentially this will come down to the components of the atomizer, precisely the number of coils that will give the atomizer more or less strength and influence the quality of your vapor. Finally, we can also answer this question with the different ways that atomizers are marketed.
What is a vaporizer and how does it work?
A vaporizer is an electronic device, containing a battery that creates a very real electrical current. Above all, your safety should be your top priority. It’s easy enough to get a new atomizer or vape if yours has turned into a dud, but recovering from an injury that resulted from an overconfident, uninformed repair attempt is a much larger order.
What does it mean when your vape says check atomizer?
“Check Atomizer” or “No Atomizer” will appear when your vape mod or pod vape isn't reading your coil correctly. This can be due to the 510 connector not reading properly (where the tank screws onto the mod), the coil not making proper contact inside of the tank, or possibly a short.
How do I fix my vape atomizer?
RecapClean all contacts on battery/mod, tank or pod.Remove and reinstall the coil (after cleaning)Try a new coil.Check the 510 pin and see if you can adjust it (mods/tanks)Try another tank on your mod.Try another mod with your tank.Adjust base of coil carefully if you can (mainly sub-Ohm coils)
How do you use a vape atomizer?
0:081:35How to use a Vape: Vaporizer Set Up Tutorial (Electronic Cigarette ...YouTubeStart of suggested clipEnd of suggested clipThe way you turn the battery on the off is by simply pressing the power button five times veryMoreThe way you turn the battery on the off is by simply pressing the power button five times very quickly to charge the battery to simply screw it into a USB charger like.
Is an atomizer the same as a coil?
The coil is a small part in an electronic cigarette which gets hot. A coil head is also known as an atomizer head. These are words for the same thing, the heating element inside an e-cigarette.
How do you know if your atomizer is bad?
Signs it's time to change your vape coilA burning taste. Vaping a dead coil will eventually result in an acrid, burning taste. ... Gurgling sounds. Vapes shouldn't gurgle. ... Weak or “off” e-Juice flavor. This often precedes a burnt taste. ... Low vapor production. The vapor produced by your coil will gradually lessen with time.
Do you need an atomizer to vape?
Before going further, it's important to note that all e-cigarettes need an atomizer to work. Cartomizers and clearomizers all have atomizers to vaporize e-juice. The main difference among the three is the delivery system.
Do you put wax directly on coil?
You can add it onto the coil. The coil at this point should be wet and waxy so it will only give you a bigger hit. We recommend you do not use a variable voltage battery on your wax chambers since they can burn it out. If you only have a variable voltage battery, put it to the lowest voltage, which is usually 3.2V.
Are atomizers safe?
Coiled Atomizers Others are unknown alloys, and companies are not always aware of what they are. To avoid vape pens with unknown alloys, always look for tests. The atomizer could contain harmful materials, and possible negative long-term effects.
What's an atomizer on a mod?
Atomizers are the heart of vaping. Vape pens and mods are the power supply unit and the atomizers are responsible for vaporizing e-liquid. The term atomizer can refer to different things. It can refer to devices containing coils or it's also used to refer to the coil inside the device.
How long does a vape atomizer last?
Most wax atomizers will need to be replaced within 4 to 12 weeks. This number depends on how often you vape, and the temperature you choose. Those who vape constantly at high temperatures will need to replace their atomizer more frequently.
What do you put in an atomizer?
How to refill atomizer?Get your favorite flavor e liquid and cap out of a new atomizer.Fill about three quarter of e juice into the plastic cap.Hold an old used atomizer and gently drip e liquid. Do not drip into the center of atomizer and wait about two minutes until e liquid is absorbed.Remove the cap and blow dry.
What wattage should I vape at?
On the contrary, even 10 watts is sufficient to guarantee a satisfying vape, which may be ideal for new vapers. As you become more experienced, it's safe to say that vaping starts to shine between the range of 40 and 50 watts.
What is the atomizer in vaping?
This is a component that makes up a vape or e cigarette. The atomizer is a crucial piece of a vaporizer and without this component almost no vaporizer would work.
What is an e-cigarette atomizer?
E-cigarette atomizers are responsible for seeding e-juice mostly and not dry materials. These types of atomizers are often found between the mouthpiece in the tank and air responsible for heating up the E juice to output vapor through the mouthpiece.
Why is there no atomizer on my 510?
The no atomizer or check atomizer often comes up when the electrode pin in 510 configuration is not pressed against the firing pin, when the prebuilt coil is not connecting inside the base of the 510 electrode, or when the RBA is not correctly connected to the deck.
What is a check atomizer?
Check atomizer is also called No atomizer. Atomizer shorts are often displayed when a coil begins to short-circuit. Atomizer short warnings will completely disrupt energy that goes into the atomizer to preserve it. Seeing these atomizer errors should never keep you from using your vaporizer.
Do you need to know all the technical terms for vaping?
There is a fair amount of technical information surrounding vaping, and it can sometimes feel a bit overwhelming especially with some of the terminology that people that vape often may use. It's very unlikely that you'll need to know all of the technical terms for vape components to use a vape successfully, but learning ...
Can you use preinstalled coils with a vape tank?
If you are using preinstalled coils with a vape tank, you'll need to make sure that the base of the coil is connected to the base of your tank.
What is an atomizer?
So you want to become a more informed vapor and amaze others with your tips and tricks!
How does an atomizer work?
As significant as an atomizer is to your vaporizer, it functions in a very simple manner. When your vape device is turned on, it activates the battery, distributing power to the other components of the device.
What atomizer type is right for you?
Now let me tell you about different types of “atomizer” that you can choose from depending on your experience:
What causes a check atomizer short?
Loose pieces of metal on the build deck will cause your mod to display “Check Atomizer” or “Atomizer Short”. Even very small pieces or trimmings of wire can cause a short or a check atomizer error on an RDA/RTA/RDTA. First, inspect the build deck closely for loose pieces of wire or other foreign objects.
How to clean a pod from a vape?
Also check inside your vape where the pod attaches to it. If you see any ejuice or dirt, clean it out with a paper towel then reinsert the pod and try again.
What to do if cleaning contact points doesn't fix check atomizer error?
If cleaning the contact points doesn’t fix the check atomizer error on your pod vape, you’ll want to carefully examine the contact pins/plates on your pod vape and on your pod for damage.
What to do if your pod vape isn't firing?
If your pod vape isn’t firing, has a blinking LED and won’t fire, or says Check Atomizer or No Atomizer, you can follow a few of the same steps listed above for tanks: 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points.
Why won't my 510 mod work?
Simply put, if your mod can’t read your tank and coil resistance properly, it won’t be able to deliver power and therefore won’t work.
What is a versed vaper?
The Versed Vaper team are a group of passionate and experienced vapers who take pride in writing helpful, quality content about vaping. From deals, to news and reviews, we've got you covered on all things vaping. Remember to subscribe to our newsletter, and follow us on Twitter, Instagram, and Facebook!
How to remove a tank from a mod?
Start by removing the tank from the mod and inspect the threading where the tank screws in for dirt , dust, or ejuice. Do the same with the 510 connector on your mod. Clean out the contacts with a paper towel, and screw your tank back onto your mod.
What is a vaporizer?
A vaporizer is an electronic device, containing a battery that creates a very real electrical current. Above all, your safety should be your top priority. It’s easy enough to get a new atomizer or vape if yours has turned into a dud, but recovering from an injury that resulted from an overconfident, uninformed repair attempt is a much larger order.
Why is my vape not recognizing my atomizer?
If your vape device isn’t recognizing your atomizer, it could be an issue as simple as an interrupted connection. Dust and debris can get in the way of the electrical current, leading to a complete mechanical failure. Other culprits can include an atomizer that’s completely screwed in, or a center pin that’s missing its mark. Take a close look at all the connection points on your device, clean them off, and make any adjustments to complete the current.
What is the pin on a vape?
The pin is the connection tip that’s found inside the 510 connector, responsible for making contact between your atomizer and vape device. If your pin is too low or too high, it can’t properly connect, and your device simply won’t work.
How to prevent vaping issues?
Take a Proactive Approach. Many vape issues can be avoided by simply performing regular cleanings and maintenance on your device. Taking proper care of your vape can help you minimize issues, and keep your vaporizer running in tip-top shape. Cleaning your vape isn’t difficult, and takes just a few moments of your day.
What tool to use to adjust vape pins?
However, if your vape isn’t one of these models, use a small tool, like a precision flathead screwdriver, to adjust the pin position ever-so-slightly.
How long does it take to read a vaporizer?
Reading Time: 4 minutes . Your vaporizer is a lot like your car: you count on it on a daily basis, it’s a critical part of your everyday routine, and you hope to avoid issues at all costs. However, just like a vehicle, vaporizers do run into mechanical problems every now and then.
How to tell if a vape is malfunctioning?
One easy way to know if your atomizer is malfunctioning is if your vape displays one of the following messages: check atomizer, no atomizer, or no atomizer found. If your vape shows one of these no atomizer messages, continue reading to find out how to proceed.
What is the best atomizer?
When caring for your atomizer, it is important to consistently clean out the inner tubes and pathways. Residue can quickly build up if using a coil design, and if left for too long then the coil can become less able to heat completely. The hits will become less flavorful, less potent, and smaller. The best atomizers we have come across are: 1 Yocan Cerum 2 Yocan NYX Wax Atomizer 3 Saber Vape Wax Coils 4 Yocan Evolve Plus XL Coils
What are coiled atomizers made of?
Most early coiled atomizers are traditionally made from ceramic materials. Almost all early vape pen atomizers contained a ceramic cup with the traditional coils wrapped over wicks design. Recently, it changed to the coils still being in the ceramic cup but wrapped over ceramic rods instead of a wick. Coiled ceramic atomizers are known for big hits, but most users now prefer quartz bowls and rods rather than ceramic for coiled atomizers, as it's more efficient and also cleaner. Ceramic atomizers are known for causing residue to stick to the sides of the bowl, while quartz is much more resistant to residue buildup.
What does low atomizer mean?
Atomizer Low means that the coil resistance is too low. Vapers who see any of these messages on their mod should stop using the vape immediately. But do not worry. These issues can be solved quickly so that the user can get back to vaping as soon as possible.
Why is my atomizer low?
A common reason why the atomizer low warning occurs during vaping is that the coil was not properly made, the connection is loose, it is not seated correctly, or it does not have an insulator. Another reason a user might get this warning is that he or she misjudged the size of the build.
Why won't my vape fire?
If the resistance of the coil is lower than what the device can tolerate , the vape will not fire. Dry burning is one way to get around this problem because it can raise the coil’s resistance. Another thing to do is add wraps to the coil, which will increase the resistance high enough so that the mod fires.
What does "check atomizer" mean?
One company may use the standard “atomizer short” error for a shorted coil, while another may say “check atomizer” for the same reason—or use it as an umbrella term for all atomizer issues.
Why do atomizers use peek insulators?
Almost all atomizers these days use PEEK insulators to separate the positive from the negative. Any damage to your insulators may cause a short, resulting in an “atomizer short” or a similar error.
What is Vaping360?
The Vaping360 team is a diverse group of experienced vaping contributors. We strive to bring you the finest content on all things vaping. Don’t forget to follow us on Facebook and Instagram for more!
Can you use a 510 pin on a mod?
While it’s somewhat rare these days, it is possible for an atomizer to not be compatible with a mod due to its 510 pin. If some atomizers work and others don’t, it’s likely a poorly designed 510 connection on the mod. 4. Low-resistance coils.
Is it worth vaping on a device?
Even if it sometimes works, it’s not worth vaping on a device with electronic damage. If your job or lifestyle is making you prone to damaging your mod, try buying one with an IP67 certification. These are water and dust-resistant, and usually rugged enough to survive most everyday accidents. 6. Chipset failure.
Can you let juice leak on a mod?
Don’t let juice leak on your mod—it may find its way to the circuitry. Overtightening atomizers – people often overtighten their atomizers, to the point where they break the 510 pin out and/or snap the ground wire internally. Don’t over tighten your atomizer.
Can vape mods be rough?
Vapers can be rough on mods for sure. Considering how many mods are in our hands, some accidents are going to happen. But, like any electronic device, vape mods need to be handled with proper care. Sometimes error messages are due to a damaged mod bugging out, and this can happen for a number of reasons.
What is an atomizer in vaping?
Posted by Evelyn on August 8, 2019. Atomizers are the heart of vaping. Vape pens and mods are the power supply unit and the atomizers are responsible for vaporizing e-liquid. The term atomizer can refer to different things. It can refer to devices containing coils or it's also used to refer to the coil inside the device.
What are the problems with vaping atomizers?
The three most common atomizer problems are: Atomizer short warning. Atomizer low warning. No atomizer found warning. Those are the warnings that will typically pop up when you run into issues with the coil.
Why is there no atomizer found?
If the warning is still there after trying to fix it then it could be an issue with the mod being used. A "no atomizer" warning almost always means the coil being used is dead or loosely seated .
What is a RTA atomizer?
It can refer to devices containing coils or it's also used to refer to the coil inside the device. There are three types of atomizer devices: vape tanks , rebuildable drip atomizers (RDA), and rebuildable tank atomizers (RTA). These devices all use a coil that heats up and transforms vape juice into vapor.
Why does my atomizer give me a short message?
There could be a number of reasons why your device is giving you a short message. If you are using a rebuildable atomizer then your coil could be touching an unintended area like the deck or cap of the casing. If you are using a tank with a pre-built coil then the coil can either be defective or it could be loose.
How to fix an atomizer short?
How to fix an "Atomizer short" warning: Place batteries on an external charger to ensure they're both charging properly. For rebuildable atomizer users (RDA/RTA), make sure the coil is not touching the cap or deck and contains no breaks in your coil.
Why is my 510 atomizer low?
The atomizer low warning means the resistance of coils is too low for the mod being used. The atomizer short warning on your mod displays when the coil is causing a short-circuit.
Sebastian2011 New Member
Just got a new vaporesso target and using uwell crown tank with .25 coil. It works fine for a couple firings then pops up 'high atomizer'. I vape at 40 watts. Any info appreciated.
Bunnykiller ECF Guru Verified Member ECF Veteran
I would assume that high atomizer means hi ohm value... either there is a faulty connection with the coil leg to the atty, a loose fitting 510 connector.. as things heat up things expand and can cause a poor connection... my first thing to check is the screws in the atty if its a DIY coil......
Sebastian2011 New Member
Thanks guys. Aren't vaping buddies the best? I cranked the mod higher and it seems to have stopped. Fingers crossed. Cheers mates!!!!