What is NI TI and SS in vape?
Stainless steel (SS), nickel (NI), and TI (titanium) are all wire materials. With the exception of stainless steel, which can be used in wattage mode and SS mode, they should only be used in those mods that correspond to them. They allow you to limit the temperature you vape at.
What is SS on Voopoo drag?
The flashing ss is temp control mode, I imagine you want normal power mode. Three quick clicks on the fire button will cycle through the tc modes - keep doing it until you get to normal wattage. 3.
What do the letters on my vape mean?
The wattage and voltage setting of your box MOD is generally indicated by a number followed by the letter “W” for wattage, and “V” for voltage. For example, your screen may display: “14.1W” and “3.81V,” indicating a wattage of 14.1 and a voltage setting of 3.81.
What setting should I have my vape on?
As a general rule, dab temperatures are set between 315℉ to 900℉. Below 315℉ is usually too low to vaporize cannabis concentrates. And above 900℉ can release carcinogens as well as a harsh, burnt vapor.
How do you adjust Voopoo drag?
2:355:33DRAG 3 mod and settings by voopoo - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf we get the up and down bar and press them. Together. We can change the theme. So we've gone downMoreIf we get the up and down bar and press them. Together. We can change the theme. So we've gone down to the next one press the fire button.
What temperature should my Voopoo drag 2 be?
I found the vapor to be dense and very tasty at around 75-85W, which is also the range recommended by Voopoo. Temperature Control vaping is also great with the Drag 2, just as it was with the original.
What does S and R mean on a vape?
The R is for Rebuildable and the S is for Smart. I'm other words when you're using a premade coil that u buy to pop into your pod or sub-ohm tank then u would keep it on “S” which basically predetermines the recommended wattage for that particular coil.
What does BVC mean in vaping?
You may also start to see the acronym BVC which stands for bottom vertical coil meaning that the coil is built vertically instead of horizontally. BVC was made very common from Aspire first with the Nautilus tank and then with their regular tanks.
What wattage should I vape at?
On the contrary, even 10 watts is sufficient to guarantee a satisfying vape, which may be ideal for new vapers. As you become more experienced, it's safe to say that vaping starts to shine between the range of 40 and 50 watts.
What wattage gives the best flavor?
The sweet spot for getting a balance of vapour and flavour is around 0.3ohms. Depending on your coil choice you'll want to up the wattage from anywhere between 50 and 100 watts.
What temp should I vape e juice at?
420 degrees FahrenheitMany people agree that 420 degrees Fahrenheit or 216 degrees Celsius is the sweet spot. You get as much flavor as possible without feeling the warmth of the vapor. If you want to add even more flavor, try a temperature between 425 and 450 degrees Fahrenheit or 218 and 232 degrees Celsius.
What's the highest mg in a vape?
Nicotine strengths are available from 0 to 50mg. It can take a few tries to get the strength that suits you. Stronger strengths (like 18mg+) would normally be more enjoyable in e-liquids with nicotine salts. The strength of free-base nicotine in a vaping substance must not exceed 20 mg/ml.
How do you use drag s?
VooPoo DRAG S Quick StartPull the pod off from the top of the mod.Turn the pod upside down.Pull the coil out from the bottom of the pod.Insert new coil into bottom of the pod and press firmly.Fill pod and allow to stand upright for 5 minutes before using new coil.
What are the different settings on Voopoo drag S?
UsageOn / Off – Five clicks of the power button.Change mode – Click the fire button x3 times. ... Adjust Wattage – use the up/down buttons.Puff Interface – Press up/down together. ... Reset Puff Counter – Press Fire button and down button.Lock device – Press Fire and up button together will lock the device.More items...
Is the Voopoo drag S for Salt Nic?
The VOOPOO DRAG S Kit is a incredibly versatile vaping system that can be geared for nicotine salts or regular eJuice, featuring the advanced Gene.
How do you set auto puff drag S?
Operations are fairly straightforward.Five clicks of the power button turn the device on and off.Three clicks of the fire button to change between “smart” and “RBA” mode on the X (the S allows you to swap between button press and auto-draw mode too).Press up or down to adjust the wattage.More items...•