If your device uses replaceable coils, disassemble the atomiser and prime your coil by placing 2-3 drops of e-liquid on the wicking holes on the sides of the coil. Reassemble atomiser, ensuring a good seal. Fill atomiser with e-liquid and allow the coil to saturate (prime) for 10 minutes.
Full Answer
Why won’t my innokin sceptre vape?
If you’re still having trouble getting your Innokin Sceptre to work, the next thing that you should do is try removing and reseating the atomizer coil. The most common reason why an Innokin Sceptre doesn’t vape is because the atomizer coil is only partially screwed in.
Does my innokin vaporizer have a manual on/off switch?
Rarely, your Innokin vaporizer may include a manual on/off switch in addition to the typical 3 presses of the firing button. You’ll find switches like this on products such as the CoolFire IV and CoolFire Z50.
How do I change the atomizer coil on my innokin sceptre?
When your pod is empty, remove it from the Innokin Sceptre and hold it with the mouthpiece facing down. Twist the pod’s base counterclockwise and remove it from the pod. You’ll find the atomizer coil attached to the base. Unscrew the current coil and screw in a new one. Make sure that the coil is connected tightly to the pod’s base.
Can you change coils on innokin e-cig starter kit?
Installing or Changing the Coil Your Innokin Adept e-cig starter kit comes with two coils. A 0.48 ohm coil comes preinstalled in the Zlide tank. You can use that coil or you can swap it out for the 1.6 ohm coil that also comes with kit or you can opt for the 1.2 ohm coil we sell separately.
How do I fix my innokin vape?
0:504:13INNOKIN GOs | TROUBLESHOOTING GUIDE - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn the base of the tank you'll find a circular metal outcropping grab a piece of tissue. And giveMoreOn the base of the tank you'll find a circular metal outcropping grab a piece of tissue. And give the metal part a clean especially the bottom as this is where the tank connects to the battery.
Why is my innokin vape not working?
If you try to vape and are stopped by a flashing button, this typically means the short-circuit protection feature has kicked in. The common culprit is wayward e-liquid; if there's any loose liquid near the connector points on the tank or battery, the device won't fire until it's cleaned up.
Why is my vape not working?
There are several reasons why your vape pen may not be working properly. Some of these causes are easy fixes, such as oil setting and getting stuck in your cartridge. Others are more technical, like a battery, atomizer or coil issue. Most of the time, your vape pen isn't actually broken.
Why is my innokin Sceptre not working?
If you're still having trouble getting your Innokin Sceptre to work, the next thing that you should do is try removing and reseating the atomizer coil. The most common reason why an Innokin Sceptre doesn't vape is because the atomizer coil is only partially screwed in.
How do you reset a vape?
0:000:31How To Do A Factory Reset on Your IQC Vaporizer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce the reset is complete the vaporizer will vibrate and button lights will. Turn. Off you.MoreOnce the reset is complete the vaporizer will vibrate and button lights will. Turn. Off you.
Why is my vape flashing and not working?
The most common ones being: Dying battery: Most often, the vape pen will blink ten times when the battery is too low for proper vaping. To fix the issue, recharge the battery. Low voltage: If the battery is charged but the pen is still blinking, it could be due to a low voltage.
When I press the button on my vape nothing happens?
Try cleaning the battery terminal and end of your clearomiser with a cotton bud. Another thing to check is that the tank or clearomiser is making contact with the battery terminal. If a previous tank has been screwed on too tightly, the battery pin may need adjusting to make a connection again.
How do I know if my vape is broken?
5 Signs That Show It's Time To Change Your Vape CoilYour Vape Tastes Burnt. This is probably the most noticeable thing that tells you your coil needs replacing, and something most vapers will experience. ... Your E-Cigarette Is Gurgling. ... Your Vape Tastes 'Strange' ... Your Coil Is Used Up. ... E-Cigarette Leaks.
How do you fix a short circuit on a vape?
Here are a few things to try to resolve atomizer short:Make sure the batteries are charging them properly by putting them in a separate charger.If using an RDA/RTA, check and see if the coil is touching the cap or deck.See if there are any breaks in the coil.Ensure that the coil is fully screwed into the tank.More items...•
Why is my innokin t18 not working?
To resolve the issue, make sure that the coil fits snuggly and that the base of the tank is secured tightly. While you are at it, check if the threading on both the coil and tank is clean. If juice or dirt is lodged on the connectors, use a cotton swab or soft cloth to wipe them down with a little rubbing alcohol.
Why does my Innokin Sceptre keep flashing green?
The green flashing like is an indicator that there is a shortage between the coil and battery.
What does it mean if your vape is flashing blue?
Vape pen blinking blue It means that the vape pen has switched to medium mode power output.
What to do if 510 connector is not threaded?
If you are using a vaporizer with a connector that is not 510 threaded, locate the brass colored contacts underneath the pod of your device and apply the same routine to them as you would your 510 connection. While cleaning your atomizer and battery connection, inspect the threads and pins for any damage.
How to clean 510 connectors?
Clean the male and female 510 threading of your device with a small amount of isopropyl alcohol. The male threads are located on the tank (atomizer), while the female threads are typically located at the top of your battery. We recommend using a cotton swab to get the isopropyl alcohol into the female threaded section. Remove all condensation, dirt, lint, dust etc from the connectors and allow them to air dry after swabbed with isopropyl alcohol. If you are using a vaporizer with a connector that is not 510 threaded, locate the brass colored contacts underneath the pod of your device and apply the same routine to them as you would your 510 connection.
What is the AFC on a vaporizer?
Many of our vaporizers come bundled with an accompanying tank (atomizer) which features a manually adjustable “AFC”, or airflow control ring. These rings can typically be turned clockwise to adjust the level of airflow you introduce to your coil when you inhale.
What is the resistance of Coolfire Z50 coil?
For example, the CoolFire Z50 supports coils from 0.2 ohms to 3.5 ohms. If your coil is lower than 0.2 ohms or higher than 3.5 ohms, you will receive a resistance error message, or “Check atomizer”.
Why does my atomizer say "Check atomizer"?
While cleaning your atomizer and battery connection, inspect the threads and pins for any damage. Dents, nicks, or cuts in these areas can consistently cause the “Check atomizer” message to occur. A damaged connector will typically need to be replaced via warranty replacement or a new product, so please be very careful not to damage your connector!
What does it mean when you have a smaller opening on an airflow coil?
With a smaller opening or less holes exposed, the less air you will pull through your coil. This simple principle applies to all of our products that feature adjustable airflow. Product shown: Innokin Ajax tank.
Where is the AFC ring on a atomizer?
While most airflow control rings are found on the bottom of our atomizers, there are a few atomizers we have that feature the AFC ring elsewhere, such as the top of the tank. If your device did not come with an included tank, you’ll likely have to adjust your airflow setting in a different way.
Why won't my Innokin sceptre vape?
The most common reason why an Innokin Sceptre doesn’t vape is because the atomizer coil is only partially screwed in. If you’re still having trouble and are certain that the atomizer coil is firmly seated, you should replace the coil.
How long to wait before vaping innokin sceptre?
Place the pod back into the Innokin Sceptre and wait five minutes before vaping. The Innokin Sceptre pod has a built-in dial that allows you to adjust the pod’s airflow. If you’re using the 1.2-ohm coil, you should turn the dial to the left. If you’re using the 0.5-ohm coil, turn the dial to the right to increase the airflow.
What Coils Work With the Innokin Sceptre?
The Innokin Sceptre works with two different coils. The kit comes with both coils, giving you an opportunity to try both and choose your favourite.
Why does my Innokin sceptre gurgle?
If your Innokin Sceptre is gurgling, the most likely reason is that you’ re using too much air pressure when vaping with the device. That’s particularly likely to happen if you’re using the 1.2-ohm mouth-to-lung coil and have the airflow dial turned to the MTL setting. If you puff harder in an attempt to get bigger clouds out of the device, you’ll overwhelm the pod’s capacity to manage airflow and will draw excess e-liquid into the atomizer coil assembly and chimney. The e-liquid caught in the pod’s chimney creates a gurgling sound and may even enter your mouth if you continue puffing too firmly. Always puff gently when using the Innokin Sceptre. If you’re not happy with the device’s vapour production, you can increase the wattage, increase the airflow or switch to the 0.5-ohm coil.
What is the difference between Innokin Endura M18 and Innokin Sceptre?
The primary difference between the two is that the Innokin Endura M18 has a smaller atomizer coil and is designed primarily for mouth-to-lung vaping. While it does have adjustable airflow, it has only two available settings. You can toggle between the settings by reversing the installation of the pod. The Innokin Sceptre, meanwhile, has a dial that allows for more precise airflow adjustments. The Sceptre also has a mesh coil available for greater vapour production, while the Endura M18 doesn’t have that option.
How to fill an Innokin sceptre pod?
To fill the Innokin Sceptre pod, lift the pod up to remove it from the device. You’ll find the silicone filling plug on the side of the pod. Remove the plug and add e-liquid through the filling hole until the pod is almost full. Replace the plug and put the pod back into the device.
How long can you use an Innokin sceptre?
As you use the Innokin Sceptre, you’re going to find that the flavour changes over time. Usually, you’ll find that you can use an atomizer coil for several days before it requires replacement – and when you’re no longer happy with the flavour you get when vaping, it’s time for a new coil.
What is the best way to charge an Innokin vaporizer?
Use a certified wall charger with a high quality USB-C cable, such as the cable provided with your Innokin MVP5.
What to do if vaporizer is hot?
If the vaporizer is becoming hot to touch, or showing another type of malfunction, discontinue using the device immediately. Disconnect the atomizer, unplug it from any charger or cables and store the vaporizer in a nonflammable environment, such as a fire retardant bag or container.
How can I verify that my vaporizer is authentic?
Locate the Product Authentication number on the product packaging. Please visit https://www.innokin.com/verify-device and follow the instructions to verify your product authenticity.
How do I use the power bank feature of the MVP5 vaporizer?
Simply plug a microUSB cable into the base of your MVP5 to charge your phone or other electronic devices! The screen of the MVP5 will show your amperage out, total capacity remaining of the MVP5 battery and amount of charge time remaining.
What is Vape While Charging?
Vape While Charging is a feature commonly seen in our mods that allows you to vape while you are charging your device . Be advised that while this feature can be convenient, it’s not recommended to vape while charging a device that is extremely low on battery life. Wait until your battery indicator on the screen indicates at least a 40% partial charge or until the charging LED changes to a yellow color before you use this feature. If you Vape While Charging when the battery indicator on the screen shows a low overall charge, you will damage the overall lifespan of the battery.
What is a 510 connector? Does my atomizer/vaporizer have one?
The MVP5 uses a high quality standard 510 connection, the standard threading for most vaporizers and tanks.
What battery safety and overheating features does this vaporizer have?
The MVP5 is equipped with a full range of integrated safety protections you’d expect from Innokin: Overheat protection, Charging protection, Short circuit protection, High Resistance protection, Cut-Off protection and Over-discharge protection.
How to replace coil on Innokin Adept?
To replace the coil, first unscrew the tank from the body of the Innokin Adept. Next, unscrew the ring from the base of the tank: If there is a coil preinstalled that you need to remove, you can do so by lifting the coil with the edge of your finger or pulling up on the coil itself:
How to contact Innokin Adept?
In addition, as always, we're just a phone call away if you need help. Call (844) 303-4545 or you can email us at: customers@kaisvirginvapor.com
How to fill a vape tank?
Filling the tank involves three quick motions: #1 First, remove the drip tip. The drip tip is designed to hold the tank closed to prevent children from accessing the vape juice and also to keep the tank from accidentally opening in your purse or pocket. Just pull up on the d rip tip and it will pop out.
What is an Innokin Adept?
The Innokin Adept allows you to adjust the airflow, creating either a more airy vape with an easier draw or a tighter vape that requires more draw to pull the air through.
What happens if a coil is dry?
If your coil material is dry, you will get what is known as a "dry hit.". You'll know you got a dry hit because it tastes nasty, like singed fabric or burning rubber. Once you singe your coil, there's no going back and you'll have to toss it. For this reason, it's important to always remember to prime the coil first!
How many clicks does an e-cigarette have?
Most e-cigs come with a 5-click on/off feature, however, the Innokin Adept did something that seems like a small change but is actually very smart design. The Innokin Adept only requires 3-clicks to activate or deactivate it.
Is VG vape juice higher than PG?
Because our natural and organic vape juices are manufactured using a 100% VG base, the viscosity is slightly higher than PG based vape juice. For this reason, giving the coil an extra 5 minute bath in the tank is a must to give the e-liquid time to fully soak into the coil.
What does a vape cutoff warning mean?
VAPE CUTOFF Warning is displayed when the puff time exceeds the set Vape Cutoff time. Solution: Vape Cutoff time is set through the Menu.
How full should a vape tank be?
Keep tank at least 1/3 full for best longevity and favors. Don’t vape if tank is empty.
What happens when battery Voltoge is lower than 27V?
When the battery voltoge is lower than27v, the device will not power on.
