To use the Pulsar
Pulsar
A pulsar (short for pulsating radio star) is a highly magnetized, rotating neutron star that emits a beam of electromagnetic radiation. This radiation can be observed only when the beam of emission is pointing toward Earth (much the way a lighthouse can be seen only when the light is poi…
How to use the pulsar APX V2 vaporizer?
How To Operate The Pulsar APX V2 The Pulsar APX V2 has an easy-to-use one-button operating system. You’ll find this button on the unit’s side directly above the LED screen. To turn this dry herb vaporizer on and off, hit the main button five times within two seconds.
What is the APX volt V3 variable voltage vaporizer for wax?
The APX VOLT V3 variable voltage vaporizer for wax features a 5-second heat time, 3.5 inch (8.89 cm) size, 1100mAh battery, 4 voltage settings (2.5V / 2.8V / 3.2V / 3.7V), pure quartz coil-less cup, 0.4ohm atomizer resistance, and low temp capability for enhanced terp flavor.
Is the APX smoker a vaporizer?
* The APX Smoker uses a combustion style heating element and is not a vaporizer. Need replacement atomizers? Get them here. Disclaimer Legal herbal use only, NOT for tobacco.
What is the best APX vape V3?
Pulsar APX Wax V3 Concentrate Vaporizer has a rating of 4.8 stars based on 212 reviews. The new and improved APX Vape V3 combines portability with a maximized herb chamber to create an unmatched vaping experience.
How do you use the Pulsar shift vaporizer?
1:373:55Grindhouse Shift Vaporizer Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing your stirrer tool load a small amount of material into the tank. Replace the silicone lidMoreUsing your stirrer tool load a small amount of material into the tank. Replace the silicone lid slide the entire tank into your heating chamber replace the mouthpiece. And you are ready to vaporize.
How do I open APX vape?
The Pulsar APX V2 has an easy-to-use one-button operating system. You'll find this button on the unit's side directly above the LED screen. To turn this dry herb vaporizer on and off, hit the main button five times within two seconds.
How do I turn on a pulsar pen?
Offers 3 color coded voltage settings: Red / 4.0V, Blue / 3.7V, Green / 3.4V. Click 5x to turn on, click 3x to change voltage, click 2x to preheat for 15 seconds, click 1x to use.
How do I turn on my APX wax pen?
If your concentrates are stickier APX recommends pre-heating the unit for about 4 seconds to allow your wax to easily melt onto the coils. Once loaded replace the glass cover and turn the unit on. To do this click the power button 5 times quickly, the LED's will flash as the device turns on.
Why is my Pulsar vape not working?
Solution #1: Most likely, the coil or atomizer does not work – make sure the coil or atomizer is properly attached and has a good connection. Solution #2: The other cause could be a dead battery. Make sure your battery is fully charged. If it still is not working, your battery could be dead.
How do I use APX Pulsar dry herb?
0:402:02Pulsar APX V2 Vaporizer Tutorial & Unboxing - Tools420 - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe pulsar a px vaporizer is pretty easy to use turn the unit on press the on button five times andMoreThe pulsar a px vaporizer is pretty easy to use turn the unit on press the on button five times and repeat the same to turn the unit off to load the unit take the top mouthpiece off note.
How do I know when my Pulsar vape pen is charged?
If the indicator lights green continuously, the battery is fully charged. You can disconnect it from the charger.
What does 10 blinks mean on a vape pen?
Dying battery: Most often, the vape pen will blink ten times when the battery is too low for proper vaping. To fix the issue, recharge the battery. Low voltage: If the battery is charged but the pen is still blinking, it could be due to a low voltage.
How do you charge a pulsar vape pen?
0:541:38How to Properly Charge Your 510 Thread Vape Battery - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe correct way to charge your battery is to use a laptop or a standard 5 volt black charger thatMoreThe correct way to charge your battery is to use a laptop or a standard 5 volt black charger that you plug into the wall.
How long do Pulsar APX wax coils last?
Most wax atomizers will need to be replaced within 4 to 12 weeks.
How do you use a pulsar XM Radio?
Simply remove the glass mouthpiece to expose the heating chamber and using the included applicator to place your concentrates at the bottom of the heating chamber. Place the mouthpiece back on the top of the unit and turn it on by pressing the power button 5 times within 2 to 3 seconds.
How do you load a pulsar Barb fire?
0:475:26Pulsar Barb Fire Wax Vaporizer Attachment Review - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt is 510 threaded so go on most batteries. And you're going to find a dab tool for putting yourMoreIt is 510 threaded so go on most batteries. And you're going to find a dab tool for putting your concentrates on the atomizer.
What is included in the APX V3 vape kit?
The vaporizer kit includes the APX V3 vape, mouthpiece, USB cable, stir tool, & cleaning brush.
How tall is the APX wax?
Get ready to make big clouds with the APX Wax V3 Vaporizer. At 3.5 inches tall, the portable size packs a big punch with a powerful 1100mAh battery and triple quartz atomizer. Enjoy the best possible taste from your concentrates with a pure quartz lined chamber.
What is the new V3 wax?
The new V3 Wax features an enhanced LED display, a 2-click hands-free Power Mode and updated USB-C fast charging. The enhanced LED display is larger than the V2 and shows the battery level with a color changing APX logo. The hands-free mode keeps you from having to engage the power button while it heats up and during your sesh.
How to clean a vape mouthpiece?
Cleaning the mouthpiece - The glass or metal mouthpiece on the top has a friction fit and can be easily removed by pulling it away from the vape body with light force.
How to clean a vaporizer with alcohol?
These steps can be performed while the mouthpieces are soaking. Ensure vaporizer is turned off and fully cooled prior to cleaning. Snap the stem of the cotton swab to release the isopropyl alcohol into the cleaning tips. Alternatively dip a dry cotton swab into the 91% isopropyl alcohol.
How to clean 510 threads?
Use the cleaning swab to wipe the 510 thread ing of the vape body.
How to cover mouthpiece with isopropyl alcohol?
Pour enough isopropyl alcohol into a soaking container to cover the glass or metal mouthpiece.
How to clean a vape chamber?
The best way to clean the chamber is with an alcohol-filled cotton swab. These steps can be performed while the mouthpieces are soaking.
How long to dry fire a vaporizer?
Swirl the cotton swab tip around all surfaces of the heating chamber and surrounding areas to remove resin and other residues. Let the vaporizer sit for 3 minutes and then dry-fire by turning it on to the highest heat setting. The heat will evaporate any remaining alcohol residue.
How long to soak silicone mouthpiece?
Separate the silicone liner from the plastic mouthpiece and place them in the soaking container for one hour.
