- Step 1: You will now have to use the tools that are provided with the Mighty Vaporizer to take all of the removable...
- Step 2: You will then have to remove the mouthpiece by rotating it from side to side. The mouthpiece will become loose...
- Step 3: You should then unlock the cap lock and remove it. This can be done by pushing it to one side and pulling up on...
How do I change the mouthpiece on my Mighty?
Start by removing the cooling unit from the top of the Mighty. Rotate the mouthpiece back and forth and gently pull it away from the cooling until it pops loose, then use the multi-tool to remove the tiny blue o-ring.
How do I remove the cap from my Mighty+ vape?
With the cooling unit still attached to your Mighty+ vape, press down on the little button nub, where the cap lock sits, and pull up to separate the two pieces. If it feels stuck, run an empty session on the highest temperature setting, and take a couple pulls to loosen up any residue inside.
How do I change the cooling unit on my Mighty+ vape?
Slide the Caplock towards the mouthpiece socket. The cooling unit splits apart into two pieces, and depending on how dirty your vape is, may give you a bit of trouble. With the cooling unit still attached to your Mighty+ vape, press down on the little button nub, where the cap lock sits, and pull up to separate the two pieces.
How often should I Clean my Mighty vaporizer?
If solely using herbs we recommend deep cleaning the Mighty Vaporizer every 30-40 sessions. The Mighty has only a few crucial pieces to clean and the Mighty Cooling Unit will account for the most of these Remove the cooling unit by twisting it off from the top.
How do you remove a Mighty mouthpiece?
2:1812:32How to clean your Mighty Vaporizer - Best tips and tricks - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou just give it a outward pull but slight side-to-side motion. And it will pop.MoreYou just give it a outward pull but slight side-to-side motion. And it will pop.
How do you change a Mighty mouthpiece?
0:020:46Crafty/Mighty Glass Mouthpiece - Product Demo - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake a second and press it down in there so it's in there firmly. Take your mouthpiece. Focus itMoreTake a second and press it down in there so it's in there firmly. Take your mouthpiece. Focus it into the gasket. Make sure it's fully situated seated in there properly.
How do you remove a vape mouthpiece?
Using your thumb, press against the corner of mouthpiece and push it away from your body. This puts much less stress on the mouthpiece allowing it to come off considerably easy. This technique applies to the accessories attachment as well.
How do you take apart a Mighty vape?
0:022:14MIGHTY - How to Clean (by Storz & Bickel) - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull out the mouthpiece and remove the seal ring. Unlock the cap lock and remove it by pressingMorePull out the mouthpiece and remove the seal ring. Unlock the cap lock and remove it by pressing against one side and pulling it up on the other. Side separate the cooling unit cap from the base.
How do you open mighty?
0:583:34MIGHTY - How to Use (by Storz & Bickel) - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake the plug. And use it to fill the filling chamber through the opening. Please make sure that theMoreTake the plug. And use it to fill the filling chamber through the opening. Please make sure that the filling chamber is not overfilled remove the filling Aid and reattach the cooling unit.
How do you remove a crafty mouthpiece?
0:542:06Crafty Plus Cleaning Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull them apart and gently pull off the mouthpiece too. Then use the Zeus bristle pipe cleaners. AndMorePull them apart and gently pull off the mouthpiece too. Then use the Zeus bristle pipe cleaners. And your small pokey tool to dislodge any remaining particles left in the nooks.
What is the mouthpiece on a vape called?
Mouthpiece. A mouthpiece can also be called a drip tip. Two types of standard drip tips are used on tanks, 510 and 810. The diameter of the 810 drip tip is 12.5mm, while the 510 drip tip is 8.5mm.
How do you clean a cart mouthpiece?
To clean the mouthpiece, dampen a cotton swab in rubbing alcohol and gently scrub the mouth-piece. Here, too, the connection is key - be sure to wipe any residue off of the piece that connects with the battery. Make sure any residue is completely removed from the mouthpiece and on the outside of the cartridge.
How do you remove the fury edge from the mouthpiece?
Removing the Mouthpiece The default mouthpiece is easy to remove. Hold the device with your thumb over the screen and press against the lip of the mouthpiece, away from the body of the device. The leverage of your thumb should pop the mouthpiece right off! You can put it back on by doing the same thing in reverse.
How do you deep clean a mighty vaporizer?
If solely using herbs we recommend deep cleaning the Mighty Vaporizer every 30-40 sessions. Remove the cooling unit by twisting it off from the top. Pull the mouthpiece out using your thumb to apply pressure on the bottom portion while simultaneously pulling up and sideways.
How do you put Mighty back together?
Insert the stainless steel screen back into the cooling unit, and put the o-rings back onto the mouthpiece and cooling unit. Then, put the two halves of the cooling unit back together, reattach the cap lock, and place the mouthpiece back into its socket.
How do you clean a Mighty vape bowl?
Ways to clean Mighty bowl Run a few pads through it to let the alcohol steam work some magic. After a few pads, use tweezers or another tool to scrub the Mighty bowl using an ISO q-tip or alcohol prep pad. Be careful. The steam can and will burn you.
How to remove a cooling unit from a septic tank?
Remove the cooling unit by twisting it off from the top. Pull the mouthpiece out using your thumb to apply pressure on the bottom portion while simultaneously pulling up and sideways. Next pull the sliding (lock/latch) piece forward towards the mouthpiece to remove the bottom portion of the cooling unit from the top piece.
Is the Mighty Vaporizer a portable vaporizer?
Cleaning. The Mighty Vaporizer remains one of the highest regarded vaporizers on the market. There are no other portable vaporizers which come close to giving you the overall vapor quality you get from the Storz & Bickel blockbuster.
Can you use a Q tip on a Mighty Vaporizer?
It is best done with the Mighty Vaporizer on as the heat will work to loosen up any build up. Oftentimes a dry qtip will get the job done but if not turning the unit off and hitting with an ISO soaked q tip will get it good and shiny.
Maintaining your Mighty Vaporizer
How often you need to clean your vaporiser will depend greatly on how often you use the device. Storz & Bickel recommends that you clean your device at least once per week.
The right cleaning tools
The first step will be to get the right tools to clean your vaporiser.
Take the vaporiser apart
Step 1: You will now have to use the tools that are provided with the Mighty Vaporizer to take all of the removable parts off. You will need to remove the cooling unit which is on the top of the vaporiser. This is done by unscrewing it until it loosens.
Soak the parts
You will now have to soak the removable parts in the isopropyl alcohol. The only part that you do not soak is the cap lock (the part with the Mighty logo on it) and the seal rings. The other parts will need to be soaked for around 30 minutes to remove dry herb debris, but you should never soak them for longer than an hour.
Mighty cleaning guide video
Check out our complete cleaning guide video for the Mighty VaporizerThis video is easy to follow and will have your favourite vape running as good as new in no time!
Take it apart
First, wiggle and pull the mouthpiece out of its socket. Then, slide the cap lock - the holographic logo - towards the mouthpiece socket, pull it up and off, and set it aside.
What to soak
Fill your container with a bit of rubbing alcohol and soak everything but the cap lock and o-rings for about 30 minutes, or until all the pieces are gunk free. Then, rinse each piece off with warm water and set them out to dry.
Clean the oven
While everything is soaking, take a cotton swab dipped in rubbing alcohol and wipe the oven clean of any sticky substances. Hold your Mighty+ upside down while you do this to keep the electronics safe from liquid damage.
Reassemble
Once all the other pieces are dry, it’s time to throw it back together. Insert the stainless steel screen back into the cooling unit, and put the o-rings back onto the mouthpiece and cooling unit. Then, put the two halves of the cooling unit back together, reattach the cap lock, and place the mouthpiece back into its socket.
Run a burnoff
Finally, we’ll run a quick burnoff to dissolve any leftover residue before it's ready for use. Turn your Mighty+ on to the highest temperature setting. Let it run through a full session until it turns itself off. And that's it!
Tips for a cleaner vaporizer
A deep cleaning will always be necessary at some point, but if you want to keep your vaporizer cleaner for longer, get in the habit of brushing out the oven after each session. A lot of buildup occurs as the vape is cooling down with dry herbs still inside, and this simple step will save you a lot of time in the long run.
tyler hixon
Tyler is a writer and photographer from Jacksonville, Florida, where you can find him reading on the beach, or on his longboard, carving up the streets of his neighborhood.
