how to fix no atomizer on vape

What does No atomizer mean on vape?

May 25, 2021 · This could be the reason why you are now getting a “No Atomizer” or “Check Atomizer” message in your vape. Thankfully the solution to this is simple. Remove the tank from the mod and check the threading where it connects to the mod. Do the same with the 510 connector. Clean the contacts and thread with a paper towel if there is gunk and debris.

What to do when your vape says check atomizer?

Jun 22, 2020 · How to Fix Check Atomizer/No Atomizer On A Pod Vape 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is... 2. Check Your Contact Points for Damage. If cleaning the contact points doesn’t fix the check atomizer error on your pod... 3. ...

Why does my vape say check atomizer?

Dec 28, 2021 · Reinstall the coil and reassemble your tank until it's clean and dry. If you're still getting 'check atomizer' or 'no atomizer,' it's time to try another (new) coil if you have one on hand; even an old or burned coil will suffice as long as the same error message appears.

How to fix atomizer on vape?

Sep 09, 2020 · Remove your tank from your e-cig and have a look at the threads and metal plate to make sure there are no larger pieces of debris there. Then take a cotton bud, or piece of paper towel and press it gently into the hole on the top of your e-cig. Twist it round as you go and make sure that you have cleaned off the top of the metal plate.

What to do if your pod vape isn't firing?

If your pod vape isn’t firing, has a blinking LED and won’t fire, or says Check Atomizer or No Atomizer, you can follow a few of the same steps listed above for tanks: 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points.

What causes a check atomizer short?

Loose pieces of metal on the build deck will cause your mod to display “Check Atomizer” or “Atomizer Short”. Even very small pieces or trimmings of wire can cause a short or a check atomizer error on an RDA/RTA/RDTA. First, inspect the build deck closely for loose pieces of wire or other foreign objects.

What to do if cleaning contact points doesn't fix check atomizer error?

If cleaning the contact points doesn’t fix the check atomizer error on your pod vape, you’ll want to carefully examine the contact pins/plates on your pod vape and on your pod for damage.

Why won't my 510 mod work?

Simply put, if your mod can’t read your tank and coil resistance properly, it won’t be able to deliver power and therefore won’t work.

How to clean a tank after taking apart?

Once you’ve taken apart your tank, unscrew your coil from the base of the tank. Now, you’ll want to clean the bottom of the coil where it screws into the tank and makes contact. You’ll also want to clean your tanks contact point with the mod as well. Once done, reseat your coil, and reassemble your tank.

How to clean a pod from a vape?

Also check inside your vape where the pod attaches to it. If you see any ejuice or dirt, clean it out with a paper towel then reinsert the pod and try again.

What is a versed vaper?

The Versed Vaper team are a group of passionate and experienced vapers who take pride in writing helpful, quality content about vaping. From deals, to news and reviews, we've got you covered on all things vaping. Remember to subscribe to our newsletter, and follow us on Twitter, Instagram, and Facebook!

What does it mean when an e-cigarette says no atomizer?

An e-cig that says ‘no atomizer’ or ‘check atomizer’ is a message that no vaper wants to see. A source of frustration because this message flashing up on your vape mod most probably means that you cannot vape.

How to get vape juice out of a tank?

Take the base of your tank off. Take care if it is full of fluid and make sure you can remove the base without the tank leaking. If not decant the vape juice out of the tank first. Now check that your coil is screwed into the base of the tank correctly.

What does it mean when your tank is sat flush with a rubber o-ring?

If you have over tightened your tank onto your mod, it can push the metal plate from the 510 connection up into the tank. This usually means that it is sat flush with a rubber o-ring. If this is the case then it won’t make a full connection to your e-cig.

How to get a tank to pop back into the correct position?

Take your tank off your mod and turn it off, or remove the battery. Then take something small, like a small screwdriver and very gently press down on the pin. You should feel the spring underneath and this can get it to pop back into the correct position. Try attaching your tank again and see if the message has gone.

Can a mod make a complete connection to a vape tank?

Over time the connection on your e-cig can gather dust, dirt and e-liquid. If this is the case and your mod can’t make a complete connection to your vape tank, then this message will display. Remove your tank from your e-cig and have a look at the threads and metal plate to make sure there are no larger pieces of debris there.

What is the guide to vaping?

Guide To Vaping is the largest online magazine blog that is dedicated to providing a vast selection of helpful and informative articles about the latest vaping news, vapor products, and CBD.

Why is my earbuds stuck?

You could have accidentally dropped your device, one of the two pins inside the connection area can be stuck due to dirt or grime, or you could have a coil that isn’t functioning properly.

Why does my mod say no atomizer?

However, once you put your top cap on, the sides are touching the coil (usually because it’s either too large or protrudes to one side too much), and that causes your mod to show you a “no atomizer” or “short atomizer” error message.

Why do vapers forget atomizer error messages?

They were added by the manufacturer to protect you from faulty atomizers, and to prevent firing mishaps that can cause damage or injury.

What does it mean when your chipset says no atomizer?

When your chipset is responsible for an “atomizer short “or a “no atomizer” error message, it means that it’s preventing firing on the basest of levels. There’s nothing here that you can fiddle with or adjust to fix this.

Why does my vape pen leak?

There’s vape juice in your vape pen – leaky atomizers are damaged atomizers. When juice seeps into your circuitry, it can damage it and cause it to show error messages when there’s actually nothing wrong with the atomizer.

What does "check atomizer" mean?

One company may use the standard “atomizer short” error for a shorted coil, while another may say “check atomizer” for the same reason—or use it as an umbrella term for all atomizer issues.

Why do atomizers use peek insulators?

Almost all atomizers these days use PEEK insulators to separate the positive from the negative. Any damage to your insulators may cause a short, resulting in an “atomizer short” or a similar error.

What does it mean when your mod is low?

If that’s the case, check the resistance of your coil . Each mod will fire at a certain resistance range; if the resistance of your coil is lower than that, your mod will refuse to fire it.

Why is my mod not working?

Six reasons for your mod errors (and how to solve them) 1. Coils may have a short. It could be something as simple as a bad factory coil, a loose connection on your rebuildable , or the factory coil itself isn’t properly seated or missing an insulator. Also, some people may misjudge the size of their builds, causing their coil to touch ...

Why is my mod not connecting to the 510 pin?

It could be due to any number of reasons. Some are just poorly designed and fail with time, others are faulty and make it through quality control.

What is Vaping360?

The Vaping360 team is a diverse group of experienced vaping contributors. We strive to bring you the finest content on all things vaping. Don’t forget to follow us on Facebook and Instagram for more!

What to do if your coil doesn't work?

If it still doesn’t work, try another coil. If the new coil works, you just got a bum coil which happens from time to time. For rebuildables, make sure to check your coils and all the connections are tight. The screws on a post may loosen a bit after during the build process—they may also loosen gradually with time.

No Atomizer

Hi there... I'm new to Yocan UNI Pro mods and have no idea why I am consistently getting a No Atomizer warning ( there is one in there). My Uni Pro is only a week old, fully charged, and I'm using the magnet adapter that came with the device. Sometimes it works, most of the time it doesn't.

Re: No Atomizer

Hi @LaurenMaurer Thanks for your thread. Please try to reload the oil cartridge, or clean the connection points of magnetic adapter. By the way, you also can refer to this page to fix this issue: https://www.yocantech.com/help-center#UNI Any further questions, please let me know.

Re: No Atomizer

I am just gonna bump this, as I have exactly the same problems as the original poster. Bought a unipro and started having No Atomizer issues with both .5 and 1.0ml amigo carts right away. Have tried cleaning the connections, tight & loose, different carts, all to no avail. So if anybody has any tips before I give up, be much appreciated.

Re: No Atomizer

I am just gonna bump this, as I have exactly the same problems as the original poster. Bought a unipro and started having No Atomizer issues with both .5 and 1.0ml amigo carts right away. Have tried cleaning the connections, tight & loose, different carts, all to no avail. So if anybody has any tips before I give up, be much appreciated.