Keep pressing up button and down button simultaneously for two seconds to rotate the screen display 180 degrees. Switch Vaping Modes: Long press the mode button for three seconds to switch among VW (H/N/S) / VT (Ni200, SS, Ti) / TCR / BYPASS / CCW / CCT modes.
How do I use the vape mod?
After keeping it stand for about five minutes, you are free to usethe device. Slide the button at the top of the mod, enabling you to enjoy a better vaping experience with the innovative variable airflow system. -Puffs in a day: Record the puffs in a day and it will be reset to zero the nextday.
What are the different vaping modes and settings?
The first setting you will encounter is the MODE SETTING. In MODE SETTING, you can set up different vaping modes for different types of coil – W, Ti, Ni, SS, M – as well as adjust pre-heat, if you’d like to have this feature up and running.
How to change wattage on Smok mod?
Quickly Switch Between SOFT, NORMAL, HARD, MAX: on a non-touchscreen SMOK mod, simply press the fire bar and the up button at the same time. From here, you can then cycle through the output settings. How To Change Wattage In TC Mode: press the fire bar and the up button at the same time.
What should you look for when buying an electric vape?
One of the most important is the maximum output duration. It can output for 10 seconds at a time, so keep that in mind while you’re vaping. Other key features include the charging voltage and amperage. It needs 5 volts and 1 amp, so make sure to charge it according to these parameters. There is also a maximum voltage output of 9 volts.
How do I change the settings on my vape mod?
How Do I Change Modes? Most mods will allow you to change between modes by pressing the fire button three times rapidly, and then either scrolling through using three more clicks of the fire button, or using the + and – buttons.
How do I change the display on my aegis mod?
The Menu. To power on the Aegis X, it is 5 fast clicks on the power/fire button. 3 fast clicks on the same button will let you change any of the main settings as displayed on the large screen. When this option is selected, you can press both the up and down buttons simultaneously to access the main settings screen.
How do you replace a vape screen?
0:171:397th Floor Vapes - How To Replace Your Vaporizer Wand ScreenYouTubeStart of suggested clipEnd of suggested clipInsert the screen with the peak facing downward once the screen is inside the actual bowl take yourMoreInsert the screen with the peak facing downward once the screen is inside the actual bowl take your pick and flip it to the peak of the screen is facing upwards.
What do the symbols on my vape screen mean?
The wattage and voltage setting of your box MOD is generally indicated by a number followed by the letter “W” for wattage, and “V” for voltage. For example, your screen may display: “14.1W” and “3.81V,” indicating a wattage of 14.1 and a voltage setting of 3.81.
How do I change the color on my aegis solo screen?
If you would like to change the color of the screen, you can hold + and - simultaneously until the screen changes color.
How do I get to GeekVape settings?
0:362:36GeekVape Aegis X mod only setup guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can change the menu get the theme the color the version. And reset to tempo factory settingsMoreYou can change the menu get the theme the color the version. And reset to tempo factory settings click into theme you can then shuffle. Through hold it to lock it in.
How do you clean a vape screen?
0:001:41How To Remove and Clean Screens For DaVinci Vaporizers - YouTubeYouTubeStart of suggested clipEnd of suggested clipStart by taking the larger screen and push it back down into the chamber using a toothpick.MoreStart by taking the larger screen and push it back down into the chamber using a toothpick.
How do I change the settings on my aegis vape?
To switch between modes, press the fire button three times quickly to open the menu. Press the adjustment buttons to choose your desired vaping mode and hold the fire button to confirm.
How do you clean a glass whip?
Be careful not to burn yourself with hot water, but try this: Draw a pot of boiling water, dip the tip of the whip glass into the water and suck the water up into the whip a few inches. Expel the water by blowing forcefully. Residue in the Whip glass will end up in the pot. Don't inhale hot water or burn yourself!
How do I change my Smok vape settings?
0:232:16SMOK Nord 2 Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd when you're wanting to adjust the wattage. Press the power button three consecutive times andMoreAnd when you're wanting to adjust the wattage. Press the power button three consecutive times and then continue pressing it to cycle through the watts.
What does the C on my vape mean?
Temperature controlTemperature control (TC) in vape mods is a technological solution for dry and burnt hits. It also creates a consistent vape while taking longer drags because the temp stays the same—instead of getting hotter. The user chooses the temperature limit, typically from a range of 300°F to 600°F (100°C to 315°C).
How do I change the color of my Smok?
Conversation. Tip: Hold down the power button and up/down button to change screen color.
How to Use Smok Mods: How to Turn It on
Almost all of SMOK’s recent run of mods utilise a fire bar over a single fire button.This is a great method for firing your mod, as it requires ver...
How to Use Smok Mods: Exploring The Display
SMOK packs a lot of information into its mods’ displays.You have wattage and TC readings, dual-battery readouts, Ohms reading, voltage, and even a...
How to Use Smok Mods: How to Access Settings
If you’re using a touchscreen SMOK mod, there will be a settings icon on the homescreen which you can simply tap to access the mod’s settings.If yo...
How to Use Smok Mods: Moving Around Inside The Menus
When you enter the settings menu (THREE CLICKS on the fire bar), you can quickly skip through the settings menus by clicking the fire bar.SMOK mods...
How to Use Smok Mods: Installing A New Coil
When you change the coil on your tank, especially if you’re using an RDA, the SMOK mod will ask you if it is an NEW or OLD coil and give you two po...
How to Use Smok Mods: Quick Settings to Remember
1. Quickly Switch Between SOFT, NORMAL, HARD, MAX: on a non-touchscreen SMOK mod, simply press the fire bar and the up button at the same time. Fro...
How to Use Smok Mods: How to Upgrade Smok Mod’S Firmware
First and foremost, make sure you have SMOK’s NuMicro ISP Programming Tool installed on your PC.Once this is installed, you need to follow the step...
Have You Seen Our Best Sub Ohm Tanks of 2018 List?
No? Where you been!?We recently published our guide to the best sub ohm tanks for 2018.We tested A LOT of tanks. Too many to remember.But these are...
How to use a smok mod?
How To Use SMOK Mods: Installing A New Coil. When you change the coil on your tank, especially if you’re using an RDA, the SMOK mod will ask you if it is a NEW or OLD coil and give you two potential Ohms readings. Select the one that is the same as your coil – if it’s new, basically, just hit the NEW option.
How to change the color of the fire bar?
From the Home screen, Click THREE times on the fire bar. Click through the menus until you reach Screen Setting. Use the buttons on the mod to move through the options until you find the color you want. Once you have the color you want, hold the fire bar for ONE SECOND. Done.
Can you fire a mod with homemade coils?
If there are any issues and/or problems with the coil, its resistance, or the connection, the mod will simply not fire and likely show an error message.
Does Smok update firmware?
SMOK does release firmware updates every now and then but these seldom change the look and feel of the UX (user experience) or how the mod’s menus and settings function. Normally, the firmware just adds more power and fixes known bugs. PLEASE NOTE: this guide is designed for newbie vapers.
What is the ECO mode on a tank?
When your battery is lower than 40%, it will automatic provide an option to go to ECO (Power ECO) mode. When your install the tank with temperature heating wire (SS, Ti, Ni), it will automatic provide an option to go to STC (Smart TC) mode.
How to reset a sprite tank?
3) Continuously pressing mode button 3 times to unlock the mode button. 4) When install a tank, it will automatic identify its coil material and resistance, press up (+) button for reset, ...
What is power mode?
Power mode is very self explanatory. You can choose the level of wattage (amount of power per second) or voltage (the force of that power). This is used to set the optimal power for your device, as written on the coil you are using, to produce the right amount of cloud and flavor.
What coils are used in power mode?
Pretty much all coils need to use with this mode, you can use Kanthal, stainless steel (SS), and nichrome ( nickel -chrome) coils. most of readily made coils are made out of Kanthal Wire, which is why power mode tends to be oh-so-popular among users of different expertise levels.
What is bypass mode?
Bypass mode gives you the experience of raw power of your battery to heat your coils. Here you can build your coils at lower resistances than is normally accepted by power or temperature control mode, meaning that the power of the hit will be determined by the sheer state of you battery and the resistance of the atomizer.
Can you set a temperature control?
You can set personalized power or temperature control settings for your convenience. On select devices, if you have a few different power or temperature settings that you normally use, you can set these as memory settings to you can easily scroll through them to change from one setting to another.
Mojoverde Full Member
I'm trying to customize the power on logo but I get error while writing the new image on the device, and even reading from device.
Mojoverde Full Member
Sure, the first image is trying to read from device and the second is trying to set a new image.
Izan Vaping Master ECF Veteran
Sure, the first image is trying to read from device and the second is trying to set a new image.
Mojoverde Full Member
What is the size, bit depth and dimensions of the original image file?
Izan Vaping Master ECF Veteran
the image I'm trying to set is 128x32 px in .BMP extension with a size of 12KB and 8 Bits/Channel if I'm not wrong (set on RGB colour).
AlphaVapeNSK New Member
hello vaporesso! gen mod is great! best mod of 2019 year! but error in everywhere in customization!!! all customization not work absolutely!!!
AlphaVapeNSK New Member
In the past, I have had the most success with matching the new file with the "original" in size, bit depth and dimensions.
Installation of battery
1. Slide and open the battery cover according to the indicator at the bottom.
Precautions for Daily Use of Leather
1. Please try to avoid scratches by sharp objects or direct friction against rough articles.
