If you’re using a touchscreen SMOK mod, there will be a settings icon on the home screen which you can simply tap to access the mod’s settings. If you’re using a non-touch device, just click the fire key THREE times to enter the Settings Menu. Once inside Settings, you can move through the menus using the UP and DOWN keys on the mod.
Are You Ready for a vape session with your Smok device?
So, you’re ready for a vape session with your awesome new SMOK device… yes, you’re looking forward to delicious, fluffy clouds of vapour and a brief period of unadulterated relaxation. And off you go; you fill your vaporiser with your favourite vape juice and push the power button. But then, wait… the device isn’t coming on. What gives!
How do I Turn on/off my Smok vape?
First, locate your device’s main fire button, which also functions as the power on/off button. Most SMOK vapes have just a single button, sometimes two or three.
How do Smok vapes work?
SMOK vapes have a lock system. This system is a protective measure to ensure that the vaporizer doesn’t misfire while it’s stored in your pocket or purse. Unlock your device, which you can typically do with 5 clicks in rapid succession.
How to fix Smok error messages on a vape?
Try screwing your tank in a little bit tighter and clearing off any dust from the 510 connection and the connection point. “Short Atomizer” or “Don’t Abuse Protects” Seeing either of these SMOK error messages is a big red flag, and you should immediately stop vaping for your safety.
How do I change my vape settings?
Typically, most vape pen batteries with a button turn on by clicking it 5 times. Most variable voltage 510-thread batteries will switch voltage settings by clicking it either 2 or 3 times rapidly. It's important to always read the vape pen instructions before using a new one.
How do you reset a vape SMOK?
Reset the tank - You can 'reset' the tank by removing it from the mod, checking the screws are tight and pressing the fire button. Then re-attach your tank and select “n” when you are asked if it is a new coil.
How do I change the settings on my vape mod?
How Do I Change Modes? Most mods will allow you to change between modes by pressing the fire button three times rapidly, and then either scrolling through using three more clicks of the fire button, or using the + and – buttons.
How do you program a SMOK vape?
1:032:19Smok Nord Unboxing & Setup - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce your pot is full pulls the cap push the pod into the device. And let it sit for 5 to 10 minutesMoreOnce your pot is full pulls the cap push the pod into the device. And let it sit for 5 to 10 minutes. This is to ensure that your coil is saturated with the juice.
Why is my SMOK vape blinking 4 times?
Resistance protection: when the atomizer resistance is lower than 0.1 ohms or higher than 2.5 ohms, the LED light will blink 4 times and the battery will automatically shut down the output.
Why did my SMOK stopped working?
If your SMOK vape isn't turning on, it could be a quick fix: Try charging your mod to see if a dead battery is an issue. Plug it into the charger and hope that you forget to recharge after your last use. Check the battery to confirm that it's properly inserted.
How do I change my Smok color?
Conversation. Tip: Hold down the power button and up/down button to change screen color.
What wattage should I vape at Smok?
Often, regardless of the type of tank, the best performance of the majority of vapes occurs between 80 and 100 watts. Higher wattages will render your coil “useless” – burn out and reduce the battery life.
Can I put wax in my Smok vape?
The answer is no—most vape pens cannot handle wax. However, although many liquid vaporizers in Scottsdale, AZ will be able to melt and atomize the wax, you must keep in mind that they are not designed to handle that process for long periods of time and will eventually break down.
How do I change settings on Smok Nord 2?
To change the device's wattage, press the fire button three times quickly. You can then press or hold the fire button to adjust the current power level. When you reach the desired power level, don't touch the fire button for a few seconds.
How do you unlock Smok?
0:100:48SMOK G-Priv 2 - How to Lock and Unlock the Firekey (Fix ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's pretty easy one two three clicks of the fire button fire key unlocks oh we're beeping look atMoreIt's pretty easy one two three clicks of the fire button fire key unlocks oh we're beeping look at that Nathan had we go into the lock mode again one two three fire key locked oh I can't fire oh.
How do I reset my Smok Nord 4?
Here's how to operate the Device: Device On/Off – Press fire button 5 times in 2 seconds. Puff Reset – Number of puffs will reset when you reach 999.
How to Use Smok Mods: How to Turn It on
Almost all of SMOK’s recent run of mods utilise a fire bar over a single fire button.This is a great method for firing your mod, as it requires ver...
How to Use Smok Mods: Exploring The Display
SMOK packs a lot of information into its mods’ displays.You have wattage and TC readings, dual-battery readouts, Ohms reading, voltage, and even a...
How to Use Smok Mods: How to Access Settings
If you’re using a touchscreen SMOK mod, there will be a settings icon on the homescreen which you can simply tap to access the mod’s settings.If yo...
How to Use Smok Mods: Moving Around Inside The Menus
When you enter the settings menu (THREE CLICKS on the fire bar), you can quickly skip through the settings menus by clicking the fire bar.SMOK mods...
How to Use Smok Mods: Installing A New Coil
When you change the coil on your tank, especially if you’re using an RDA, the SMOK mod will ask you if it is an NEW or OLD coil and give you two po...
How to Use Smok Mods: Quick Settings to Remember
1. Quickly Switch Between SOFT, NORMAL, HARD, MAX: on a non-touchscreen SMOK mod, simply press the fire bar and the up button at the same time. Fro...
How to Use Smok Mods: How to Upgrade Smok Mod’S Firmware
First and foremost, make sure you have SMOK’s NuMicro ISP Programming Tool installed on your PC.Once this is installed, you need to follow the step...
Have You Seen Our Best Sub Ohm Tanks of 2018 List?
No? Where you been!?We recently published our guide to the best sub ohm tanks for 2018.We tested A LOT of tanks. Too many to remember.But these are...
How to use a smok mod?
How To Use SMOK Mods: Installing A New Coil. When you change the coil on your tank, especially if you’re using an RDA, the SMOK mod will ask you if it is a NEW or OLD coil and give you two potential Ohms readings. Select the one that is the same as your coil – if it’s new, basically, just hit the NEW option.
How to change the color of the fire bar?
From the Home screen, Click THREE times on the fire bar. Click through the menus until you reach Screen Setting. Use the buttons on the mod to move through the options until you find the color you want. Once you have the color you want, hold the fire bar for ONE SECOND. Done.
Can you fire a mod with homemade coils?
If there are any issues and/or problems with the coil, its resistance, or the connection, the mod will simply not fire and likely show an error message.
Does Smok update firmware?
SMOK does release firmware updates every now and then but these seldom change the look and feel of the UX (user experience) or how the mod’s menus and settings function. Normally, the firmware just adds more power and fixes known bugs. PLEASE NOTE: this guide is designed for newbie vapers.
How many clicks to unlock a vape?
Unlock your device, which you can typically do with five clicks in rapid succession. Most vapers simply get in the habit of clicking the button rapidly until the indicator light turns on, so you don’t have to literally count out five clicks every time.
How many buttons does a smok have?
Most SMOK devices have just a single button, sometimes two or three. If your specific device has more than one button, and you aren’t sure which one is the main fire button, take a quick look at your instruction manual. It, like many people, you tossed the manual in the trash after opening the box, all hope is not lost.
Why is my vape juice not coming in contact with the charger?
There’s a faulty connection somewhere in your device. Whether it’s a bad charger or a firing pin that’s getting stuck, anything that leads to an incomplete electrical connection is going to be an issue. It could be that your firing pin has vape juice on it, or it might not be coming in contact with the charger.
Does Smok vape work?
However, if attempting to unlock your device doesn’t work , you can try doing one or two different things. The vape battery needs to be charged.
Do smoks have a manual?
Luckily for you, most SMOK vapes have an online manual that you can find with a quick Internet search. A little tip for your next vape device: read the manual cover to cover and store it in a safe place for when you need to refer back to it. Like all vaporisers, SMOKs have a lock system.
SMOK Nord 4 vs. Nord X, Nord 2 and Nord: Is It Worth the Upgrade?
If you’re followed the development of the SMOK Nord series, you’ve probably noticed that there’s been quite a lot of feature creep over the years.
What Pods and Coils Are Available for the SMOK Nord 4?
If you’re familiar with the SMOK Nord series, you know that the coils are interchangeable between the different devices. As long as you’re using the correct pod for the coil – and the coil’s resistance is within the device’s supported range – you can use any coil with any device.
How to Charge the SMOK Nord 4
You can charge the SMOK Nord 4 by connecting it to your computer using the included USB-C cable. When the device charges, the screen displays a percentage indicator. It also displays an estimate of how long it’ll take until the charging process is complete. When the device is fully charged, the screen will display “100%.”
How to Fill the SMOK Nord 4
To fill the SMOK Nord 4, start by pulling the pod out of the device. You’ll see a red silicone stopper on the side of the pod. Lift the stopper and add e-liquid to the pod until the reservoir is almost full. Replace the pod and return it to the device. Don’t begin vaping until you’ve given the coil a few minutes to absorb the e-liquid.
How to Vape with the SMOK Nord 4
After you disconnect the SMOK Nord 4 from the charging cable, you’ll probably find that the device is turned off. Press the fire button five times quickly until you see the SMOK logo. Give the device a moment to start up, and you’ll be ready to vape.
How to Replace the SMOK Nord 4 Coil
After several days of vaping, you’re going to find that the SMOK Nord 4 doesn’t produce the same flavor quality that it did when the coil was new. That means it’s time for a new coil. To replace the SMOK Nord 4 coil, start by removing the pod from the device. On the bottom of the pod, you’ll see the circular outline of the coil.
How to Fix Problems with the SMOK Nord 4
The engineers at SMOK have been designing industry-leading vaping devices for many years now, and that means you can generally expect a completely problem-free experience with the SMOK Nord 4. If you do happen to encounter an issue, though, we’ve got your back.
Why is my vape not working?
If the vape appears to be on, but the display is dark, you may have accidentally activated “stealth mode.”. Quickly press the fire button three times to turn off stealth mode. If this doesn’t work, you may need to upgrade your firmware. Otherwise, the problem might be caused by screen damage or another related issue.
How long should I soak my SMOK coil?
Allow the coil to soak inside of the tank for about 20 minutes, then take a few dry puffs before using the fire button to begin vaping. Check your output wattage. Make sure that your mod’s output matches the recommended output wattage on the side of the SMOK coil.
What is the best brand of vape?
There’s no doubt that SMOK is one of the vape industry’s best brands, crafting top-of-the-line mods and pod systems like the SMOK Nord, SMOK Morph, SMOK NOVO, and so many more.
How to fix a coil that tastes burnt?
Here are a few suggestions for how to fix coils that taste burnt: Replace your coils when needed. Expect to replace coils every few weeks or so (or about 50mL of e-juice, according to SMOK guidelines). Burnt-tasting coils are usually the first sign that it’s time to switch them out for new ones.
Can you fix a dead vape mod?
Luckily, as just about any seasoned vaper will tell you, problems with a vape mod are often very easy to fix, being forced to replace a dead mod is a pretty rare occurrence. Often, a seemingly serious mod issue is simply the result of user error and can be resolved in next to no time.
How to vape with a smok?
How to Vape With the SMOK RPM 2. To vape with the SMOK RPM 2, puff on the device while holding the fire button. The RPM 2 has an 80-watt power range, but you should begin vaping at a much lower wattage than that until you’re certain that the coil you’re using can operate at 80 watts without burning the cotton wick.
How to charge a SMOK RPM 2?
The SMOK RPM 2 has a USB charging port and comes with a charging cable. To charge the RPM 2, use the cable to connect the device to your computer. The device’s display will indicate when the charge cycle is complete; disconnect the charging cable at that time.
What is a SMOK RPM 2?
The SMOK RPM 2 pod system is a device that deftly straddles the line between the simple pod-based vaping devices that beginners use and the more advanced and feature-rich mods that expert vapers prefer. It’s got the small size and convenience that made you fall in love with pod systems, but it’s also got some of the “power user” features that you’d expect to find in a full box mod.
Why does my SMOK RPM 2 make a gurgling sound?
If you flood the coil, you’ll notice a gurgling sound when you vape as the excess e-liquid begins to creep up the pod’s chimney.
How to fill a e-liquid pod?
Insert the tip of your e-liquid bottle into the pod’s filling port and squeeze the bottle gently until the pod is nearly full. Leave a bit of room for air at the top of the pod. Close the filling port and return the pod to the device . If you’re filling a new pod for the first time or replacing the coil, refer to the next section about how ...
Is the Smok RPM 2 compatible with the coils?
The RPM 2 is compatible with the coils for the original SMOK RPM and also has several new coils of its own. With the replaceable coil system, the SMOK RPM can deliver whatever type of vaping experience you want. Enjoy a high-nicotine mouth-to-lung experience or chase clouds to your heart’s content – the choice is yours.
First Things First: Charge Up The SMOK Nord
This is important. Your SMOK Nord might power-up, but it’s been sat in its box for weeks, maybe months at a time, so you’ll want to give it a good 60 minute charge before using it for the first time.
How To Prime SMOK Nord Coils (And You Need To Do This)
This one is SUPER important. You have to prime the SMOK Nord’s coils before using them. Failure to do so may lead to burning them out prematurely – and nobody wants that.
Stopping Dry Hits On The SMOK Nord
Once you’ve primed the SMOK Nord coil, insert it into the top cap. Make sure the white line on the bottom of it is pointing at the front and back of the device (not to the sides). This ensures your coil is installed properly and will wick correctly.
How To Check SMOK Nord Battery Life
The SMOK Nord has a fire key. It’s handy for tactile firing and, generally speaking, I prefer this style to breath-activated pod mods.
Anything Else I Need To Know?
Nope, that’s literally it! As I said earlier, the SMOK Nord is a fantastic device that is super-simple to use. It has a kick-ass battery life, especially when used with its MTL coils, and the flavor is great (with both styles of coils).
