The Asvape Micro supports 2 coils to suit your preferences. The 0.5ohm coil requires more power but gives more flavour, vapour and a warmer vape. Asvape recommend it to be used at 20-25w though it can be used lower.
Full Answer
Why build a vape coil?
All joking aside, there are plenty of reasons to build a vape coil rather than using pre-built or ‘stock’ coils… It gives you the ability to experiment with dozens of different coil wire types, vape coil builds and styles.
What is the difference between micro and macro vape coils?
It’s that simple. Micro: a micro coil build is a coil that has an inner diameter of up to 2 mm. Macro: a macro coil build is a coil that has an inner diameter that’s 2.5 mm and above. The bigger the inner diameter of the vape coil, the higher its resistance, and vice versa.
Do mesh coil disposable vape coils have hot spots?
That tends to create a hot spot in the middle of the coil, and the hot spot often ends up burning the cotton wick and degrading the device’s flavor quality. A mesh coil disposable vape, on the other hand, doesn’t tend to have hot spots.
What are Clapton vape coils and how do they work?
This is due to the larger surface area and the fact the Clapton vape coil acts as a wick of sorts as the e-juice will settle in ‘pockets’ running along the coil. A far more advanced vape coil build than the single macro coil; this is one we suggest you wait to try when you’ve got a bit more coil building experience.
How to put wax on a coil?
Can you clean wax coils?
Can you use a vape coil for wax?
Can you use wax in a vape pen?
What are micro coils in vaping?
A micro coil is basically an ordinary coil that's has been wound in such a way that the coil material of each individual wrap is touching the wrap some on either side of it leaving as little gap between them as possible.
What coil should I use for my vape?
The standard or regular level of ohm when it comes to vaping and your clearomizer is between 2.4 and 2.8. This is by far the most common ohm range chosen by those looking for replacement coils, with the most commonly chosen being 2.5. This standard level tends to offer the most consistent level for your vape.
What ohm coil is best for flavor?
around 0.3ohmsThe sweet spot for getting a balance of vapour and flavour is around 0.3ohms. Depending on your coil choice you'll want to up the wattage from anywhere between 50 and 100 watts.
Are spaced coils better for flavor?
No matter spaced coils or contact coils, the flavor depends on the e-juices and atomizers. Meanwhile, wattage and heating wire material also effect the flavors.
What is the difference between a 0.6 and 1.2 coil?
The 0.6ohm coil is perfect for hybrid sub vaping that want more clouds and low nicotine dosage. The new 1.2ohm coil is for true mouth to lung vaping and perfect for high nicotine dosage without flavourloss.
How many puffs Should a coil last?
On average, a decently constructed coil for a sub-ohm tank should last you 4 days to 1 week. If you vape less because you cannot vape during work hours, or you do not vape throughout the day, then your coils are likely to last twice as long.
Why can't I taste the flavor in my vape?
Vaping can sometimes cause a dry mouth simply by requiring so much mouth breathing (inhaling a vape), which can dry up saliva. When we don't have enough saliva, the ability to taste is almost non-existent. Flavor fatigue is another culprit behind vape tongue resulting in you not tasting your e-juice.
What is Vapers tongue?
Vaper's tongue (also known as vaper's fatigue) is a term that covers taste-related ailments. Often this happens from frequent use of a single, individual flavour. So, if you've been vaping the same flavour for a few weeks. you'll probably start to notice the difference in taste or lack thereof.
What is mouth to lung vaping?
With mouth to lung (M2L or MTL) vaping, you inhale the vapour into your mouth first, collect it there, then breathe it fully into your lungs. Smokers will be particularly used to mouth to lung vaping, as it's a similar process to smoking cigarettes.
Which is better Kanthal or stainless steel?
Compared to kanthal, stainless steel has a slightly lower resistance and a slightly faster ramp-up time for a given wire gauge. Unlike some of the other non-kanthal coil materials, people generally find that stainless steel doesn't introduce any off flavors that require getting used to.
Can you vape stainless steel in wattage mode?
Stainless steel: this wire is very popular and readily available. It comes in various grades such as 304, 316, 316L, 317, and 430 but the most common is SS316L. SS can be used in wattage or temperature control mode.
What is KA1 coil?
Product Details. Made of KA1, the Geekvape Zeus Coil is a meshed coil for longer lifespan. The quick-slide coil design allows for fast access coil replacement.
How are micro and macro coils created?
Micro and macro coils are created by taking a single piece of wire and wrapping it around a screwdriver, drill bit, or coil jig. The difference between a micro and a macro coil is the inner diameter of the coil. It’s that simple.
What is macro coil?
Macro: a macro coil build is a coil that has an inner diameter that’s 2.5 mm and above. The bigger the inner diameter of the vape coil, the higher its resistance, and vice versa. Likewise, the thicker the gauge of wire used, the lower the resistance will be.
How to build a coil for a RDA?
First, examine the deck and see if it is a dual or a single-coil atomizer. Then check the size of the deck and see how large your build can be—you don’t want your coils to touch the top cap as this will cause a sort.
Why do you need to have two coils?
When doing a dual coil build, it’s essential for both coils to be identical in size and form, to ensure that they heat up properly. Dual-coil builds obviously create more vapor than a single coil of the same specs, but require double the power to perform.
What do you use to pinch coils?
Wire: any of the vaping wires would do. Flush cutters: wire cutters that can cut close in small spaces. Ceramic tweezers: to pinch your coils while pulsing. Fine tip tweezers: to fluff your cotton and place it inside the wick ports. Small metal rod: a small screwdriver, or coiling tool.
How to save money on vaping?
One of the best ways to save money in vaping is to build your own coils. Rather than buying disposable coil heads every week, you can make your own. It’s a fun hobby that vapers not only take pride in, but get to enjoy the fruits of their labor. The way to get good at it is through practice. Although, it’s perfectly reasonable for first-time ...
What is a parallel coil?
In essence, a parallel coil is made out of two or more wires wrapped next to each other. Resistance is divided by the number of wire strands, so make sure you are aware of your device’s limits when building parallel coils. For beginners, a dual parallel 26-gauge Kanthal coil would be a nice starting point.
Where is the coil located on a vape?
The coil is either situated at the top or the bottom of the atomiser. While variations in coil design may change the vapor and flavor output, vape coils essentially all work the same way.
How to get a vape coil to glow?
Before it has a chance to cool down, grab your needle nose pliers and gently squeeze the two ends of your vape coil together. Rinse and repeat until your coil is glowing evenly starting from the centre and moving towards the outer wraps.
How to use coil jig?
Use your Coil Jig (which should still be through the centre of your coil) to push and pull the coil until it’s positioned exactly how you want it. When you’re satisfied with the position and the coil is as even as possible, remove the Coil Jig and give yourself a pat on the back.
What is vertical coil?
The vertical coil can be wicked on either the inside or outside, which is more commonly known as a ‘chimney’ coil. These coils have gained popularity, due to the improved airflow and flavor as more of the coil surface area is in contact with the wick.
What happens when you heat up a mod?
When you fire your mod and heat the coil, the e-juice is vaporised and this vapor is what you inhale.
Is nickel a good heating wire?
Nickel has a very low resistance to electrical current, which means it’s one of the fastest heating wire types. However, it’s normally used only in temperature control mode so may not be the best choice for your first attempt at vape coil building.
How long do vape coils last?
In general, vape coils last between 7-14 days in most atomizers. Obviously, the more you vape and the hotter you vape, the more often you will need to replace your coils because they will get burnt out faster.
Which is better for vaping: Mesh or Ceramic?
If you do a lot of MTL (mouth to lung) vaping, ceramic coils help prevent coughing or inhaling too much of your vapor at once. Mesh coils on the other hand are better for DL (direct to lung) vaping, and will help produce more vapor, which equals bigger clouds.
What is the atomizer in an atomizer?
The atomizer in your unit is responsible for heating and vaporizing your e-liquid – it’s the workhorse of your setup. The mechanics are relatively simple – a coil of wire is wrapped in some type of wicking material, and the e-liquid is absorbed by the wick.
What is the difference between a lower ohm coil and a higher resistance coil?
Lower ohms mean more current and a hotter coil, which means warmer and more voluminous vapor . If you prefer a cooler vape, go with a higher resistance coil.
How to clean coils in a atomizer?
Just rinse them in hot water, shake them off gently, and rub away any burnt on gunk with a soft cloth. Then reinstall them into your atomizer and re-prime.
How often should I change coils in a box mod?
If you are a very heavy vaper, you may have to change your coils in your atomizer every week, but many people can get 2-3 weeks out of them with proper maintenance. DIRECTVAPOR has a huge selection of replacement coils for any style of box mod.
How to tell if coils are out?
Some of the signs that your coils are going out include a notable burnt flavor and a reduction in the amount of vapor being produced, or inconsistency in the quality of your vapor. This is caused by a coil that has burnt out or accumulated too much residue to heat your juice effectively.
Why is my vape juice sitting on my coils?
Vape juice that's been sitting on your coils is exposed to dust and bacteria. This applies especially to rebuildable atomizers. Dust is inevitable. The longer e-juice has been out of it's sealed bottle, the more prone it is to acquire dust and any other floating particles in the air over time.
Why does my vape coil burn out?
Chain vaping is when a vaper takes multiple draws within a small time frame. Taking multiple draws over a few seconds will dry out the wick faster than it can soak up e-juice.
Why does my new coil pop out?
Running high wattage through a brand new replacement coil will cause it to pop and immediately burn out, since the coil goes from having no current and heat to having extreme amounts of both.
How to fix a vape that tastes burnt?
So the best way to fix the burnt taste is by changing the coil, priming it properly, vaping at a lower wattage, or vaping lower VG juice.
What is a vapebox?
Vapebox is a subscription service that sends out new juice, vape starter kits, and atomizers every month. Every Vapebox is custom tailored to your flavor preferences. If you are interested in learning more or in receiving free vape juice, click the button below.
Why does sugar caramelize on vape coils?
High sugar content e-liquids can present a problem when it comes to long vaping sessions. When sugar is exposed to high heat, it'll instantly caramelize. Since e-liquid is only exposed to high heat on the coil, this means that some sugar will caramelize on the wick.
Why does my new coil taste burnt?
The most common reason why a new coil taste burnt is because it was not primed for enough time. Remember to prime the coil for at least 10 minutes and avoid high power vaping for the first puff. After it is primed and ready, set up your device at a low wattage range.
How to thread a wick?
The best way to thread your wick is to tightly roll one end of your wick down to a point so that it can be threaded through like a needle.
What is the least expensive wicking material?
Each one has its own pros and cons. Here’s a quick overview of your options for wicking: Organic Cotton: Organic cotton is one of the least expensive wicking materials around, and it is easily accessible in cotton ball or rope form.
Can you wrap a wick around a mesh?
If you choose to purchase wicks such as ekowool or stainless steel that come in a rigid mesh form, you may want to wrap your coil around the mesh when you are building instead of building the coil separately. This eliminates one step and makes it very easy to get your wick perfect every time.
Can you thread a wick through a coil?
Remember, you will need to thread your wick through your coils, so it needs to be able to fit. However, you don’t want it to be so small that it can easily slip out of the coils. Once you get the hang of this it’s pretty easy, but for your first few wicks, try to thread the wick through the coil and see how it fits.
How to put wax on a coil?
You can use your finger too as long as your wax isn't too gooey. After loading your wax, put the mouthpiece over the coil. Press and hold down the power button.
Can you clean wax coils?
Unfortunately, these types of wax coils are very difficult to clean. Most of our customers say that continuously holding down the power button and heating the coil will burn off as much residue as the coil can. The best way to understand wax coils is to think of it as a light bulb.
Can you use a vape coil for wax?
Vape coils can be used for wax only. DO NOT use dry herbs or liquids with these coils. The heating element is composed of a ceramic rod wrapped with a nickel alloy coil. Micro Vape Coil FAQ. How to use Micro vape coils.
Can you use wax in a vape pen?
Vape coils can be used for wax only. DO NOT use dry herbs or liquids with these coils. Before you even load shatter or crumble into your ceramic rod coil, you first want to firmly press the coil into your vape pen battery. Make sure the battery is on and then press and hold down the power button.
Orders, Shipping & Tracking
About Membership
- Q: How to register ASVAPE membership? A: You will automatically gain our membership once your first order is completed.
Cooperration
- Q: About Dropshipping A: Please visit “Dropshipping” on the website. Q: About Distribution Alliance A: Please visit“Referral Program” on the website. Q: How to Become a Distributor? A: Please visit“Wholesale” on the website.
Products & Fit
- Q: How to download firmware update? A: ASVAPE current offers firmware updates for TOUCH and MICHAEL. Please click " Firmware Update" to download. Q: How can I prevent coil burn？ A: 1. If it’s your first time filling the pod/coil, wait up to 5 minutes for the coil to prime; 2. Always make sure you have enough e-liquid in the tank; 3. Don’t chain vape; 4. Higher levels of PG might help; …