No Coil Detected – GeekVape Aegis Legend Kit Instruction
- Your coil head may be too tightly connected to the atomizer base, causing an error A: Please reinstall the coil head. Don’t need to tighten too much, try again
- If you still can’t solve the problem, then it may be that your coil head is broken. ...
- If you still can’t solve your problem, I think you need to consider your 510pin damage. ...
Full Answer
Why is my coil not working on my vape?
If your coils are touching the build deck then this can lead to error messages on your vape. Be sure that your coils are installed properly and that only the legs are in contact with the build deck. Reposition your coil using a screwdriver or coiling rod if it’s touching another part of the build deck.
What does “no coil detected” mean?
You may very well see a No Coil Detected warning on your device, and it’s possible that it isn’t a problem with your mod, it isn’t a problem with your tank, but instead a problem with the coil head. You see, this No Coil Detected warning is all about a connection issue, so somewhere there are two pieces that aren’t making a solid connection.
Does geekvape say no coil detected?
Since there are tons of GeekVape customers being affected by this GeekVape No Coil Detected warning, and unfortunately, a lack of customer support, Guide To Vaping feels the need to do what it does best, which is to provide vaping content that’s designed to help vapers.
Why is my vape device not recognizing my atomizer?
If your vape device isn’t recognizing your atomizer, it could be an issue as simple as an interrupted connection. Dust and debris can get in the way of the electrical current, leading to a complete mechanical failure. Other culprits can include an atomizer that’s completely screwed in, or a center pin that’s missing its mark.
Why is my vape saying no coil?
“Check Atomizer” or “No Atomizer” will appear when your vape mod or pod vape isn't reading your coil correctly. This can be due to the 510 connector not reading properly (where the tank screws onto the mod), the coil not making proper contact inside of the tank, or possibly a short.
Why is my coil not working?
Check your tank to make sure you have enough e-liquid. If your tank is completely full but you still have weak vapor, it is possible that your atomizer or coil has been flooded. If this happens, simply take your atomizer apart and clean it with a paper towel or gently blow through it to get the excess liquid out.
How do you reset the coil on Aegis legend?
GeekVape Legend 2 Menu Once in Output adjustment mode, you can scroll down to adjust coil resistance and reset puff count by pressing the fire button. Press and Hold Fire & + button – Brightness Up.
How do you fix a coil atomizer?
1:176:58How to fix a no atomizer message on your vape - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn how old is your coil is it dead out the box let us go step by step to try and fix this problem isMoreIn how old is your coil is it dead out the box let us go step by step to try and fix this problem is your atomizer head screwed in right take the base of your tank. Off take care if it is full of
How do I get my vape to work again?
The best way around this problem is to vape with one of your fingers around one of the inlet vents. This increases the airflow pressure and might get the sensors up and working again.
Why is my vape lighting up but not hitting?
A disposable vape uses an airflow sensor to detect when you puff. Sometimes, a disposable vape that doesn't hit isn't working because the airflow sensor isn't sensitive enough or because the sensor is blocked by condensation inside the device.
Why is my Geekvape not working?
Geek Vape Aegis Solo Not Working If nothing happens when you attempt to use the Geek Vape Aegis Solo, it's likely that the battery is dead or that the device is locked. To unlock the device, press the fire button five times quickly. If the device still doesn't work, try charging the battery.
How do I reset my Geekvape?
Restore Factory Settings: When the device is turned off, press and hold "+" and "-" button at the same time, the screen will display firmware version number, and then press and hold fire button, "+" and "-" button all at the same time to restore factory settings, a prompt as "CONFIG RESET" will be displayed on screen ...
How do you prime a vape coil?
To prime a new coil, simply fill your tank with e liquid and leave it to stand for a few minutes before vaping. As above, this will allow the cotton inside your new coil to absorb plenty of e-liquid ready for that first, tasty vape.
How do you clean a vape coil?
How to clean your CoilLet your coil soak in ethanol, vinegar, or cheap vodka for at least a couple of hours.Place it under the tap and rinse.Rinse once more with some distilled water.Blow air on the open side of your coil to force water to the wicking holes.Set it aside until all water has evaporated.
How do I get rid of no atomizer?
RecapClean all contacts on battery/mod, tank or pod.Remove and reinstall the coil (after cleaning)Try a new coil.Check the 510 pin and see if you can adjust it (mods/tanks)Try another tank on your mod.Try another mod with your tank.Adjust base of coil carefully if you can (mainly sub-Ohm coils)
How much does a coil cost for a vape?
The coils—which can come in pods, cartridges, or little metal housings—usually cost in the $1-5 range per. They need to be replaced about once a week (but sometimes longer in between).
AegiSolCube New Member
I am using the tank from my obs cube which work fine on the obs cube with my Aegis Solo.
UncleJunkle Vaping Master Verified Member ECF Veteran
Please try another atomizer that is working fine in your other mods, and check if you have built the coils correctly.
UncleJunkle Vaping Master Verified Member ECF Veteran
Personally, I believe the Solos have positive 510 pins that sit a hair lower than most other mods and/or the 510 spring on them gets fatigued over a short time causing atomizer that once connected to not connect anymore.
Bronze ECF Guru Verified Member ECF Veteran
The paint wore down on the plastic trim piece that surrounds the leather portion. Removed and repainted it. The actual color is darker than the photo. More of a cranberry color (muddy red). Doesn't stand out as much as the photo suggests. Rust Oleum Colonial Red.
How to tell if a vape is malfunctioning?
One easy way to know if your atomizer is malfunctioning is if your vape displays one of the following messages: check atomizer, no atomizer, or no atomizer found. If your vape shows one of these no atomizer messages, continue reading to find out how to proceed.
Why is my vape not recognizing my atomizer?
If your vape device isn’t recognizing your atomizer, it could be an issue as simple as an interrupted connection. Dust and debris can get in the way of the electrical current, leading to a complete mechanical failure. Other culprits can include an atomizer that’s completely screwed in, or a center pin that’s missing its mark. Take a close look at all the connection points on your device, clean them off, and make any adjustments to complete the current.
What is the pin on a vape?
The pin is the connection tip that’s found inside the 510 connector, responsible for making contact between your atomizer and vape device. If your pin is too low or too high, it can’t properly connect, and your device simply won’t work.
How to prevent vaping issues?
Take a Proactive Approach. Many vape issues can be avoided by simply performing regular cleanings and maintenance on your device. Taking proper care of your vape can help you minimize issues, and keep your vaporizer running in tip-top shape. Cleaning your vape isn’t difficult, and takes just a few moments of your day.
What tool to use to adjust vape pins?
However, if your vape isn’t one of these models, use a small tool, like a precision flathead screwdriver, to adjust the pin position ever-so-slightly.
How long does it take to read a vaporizer?
Reading Time: 4 minutes . Your vaporizer is a lot like your car: you count on it on a daily basis, it’s a critical part of your everyday routine, and you hope to avoid issues at all costs. However, just like a vehicle, vaporizers do run into mechanical problems every now and then.
What is a vaporizer?
A vaporizer is an electronic device, containing a battery that creates a very real electrical current. Above all, your safety should be your top priority. It’s easy enough to get a new atomizer or vape if yours has turned into a dud, but recovering from an injury that resulted from an overconfident, uninformed repair attempt is a much larger order.
What to do if your pod vape isn't firing?
If your pod vape isn’t firing, has a blinking LED and won’t fire, or says Check Atomizer or No Atomizer, you can follow a few of the same steps listed above for tanks: 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points.
How to clean a pod from a vape?
Also check inside your vape where the pod attaches to it. If you see any ejuice or dirt, clean it out with a paper towel then reinsert the pod and try again.
What to do if cleaning contact points doesn't fix check atomizer error?
If cleaning the contact points doesn’t fix the check atomizer error on your pod vape, you’ll want to carefully examine the contact pins/plates on your pod vape and on your pod for damage.
Why won't my 510 mod work?
Simply put, if your mod can’t read your tank and coil resistance properly, it won’t be able to deliver power and therefore won’t work.
What causes a check atomizer short?
Loose pieces of metal on the build deck will cause your mod to display “Check Atomizer” or “Atomizer Short”. Even very small pieces or trimmings of wire can cause a short or a check atomizer error on an RDA/RTA/RDTA. First, inspect the build deck closely for loose pieces of wire or other foreign objects.
What is a versed vaper?
The Versed Vaper team are a group of passionate and experienced vapers who take pride in writing helpful, quality content about vaping. From deals, to news and reviews, we've got you covered on all things vaping. Remember to subscribe to our newsletter, and follow us on Twitter, Instagram, and Facebook!
Why is my mod reading the new tank correctly?
If your mod is reading the new tank correctly, it could be a problem with the coil on your other tank. You might also want to clean the contact points on the tank that was giving you the error. If your mod is still reading “check atomizer” with a new tank, it’s probably a problem with your mod.