“Check Atomizer” or “No Atomizer” will appear when your vape mod or pod vape isn’t reading your coil correctly. This can be due to the 510 connector not reading properly (where the tank screws onto the mod), the coil not making proper contact inside of the tank, or possibly a short.
Is your vape mod not reading the coil properly?
It will inevitably happen at some point and it is usually an extremely easy fix. If you press the firing button on your e-cig and you see the message ‘no atomizer’ or ‘check atomizer’ it means that your vape mod is not reading the coil within your vape tank properly.
Why is my vape not reading my atomizer?
“Check Atomizer” or “No Atomizer” will appear when your vape mod or pod vape isn’t reading your coil correctly. This can be due to the 510 connector not reading properly (where the tank screws onto the mod), the coil not making proper contact inside of the tank, or possibly a short.
What does “no coil detected” mean?
You may very well see a No Coil Detected warning on your device, and it’s possible that it isn’t a problem with your mod, it isn’t a problem with your tank, but instead a problem with the coil head. You see, this No Coil Detected warning is all about a connection issue, so somewhere there are two pieces that aren’t making a solid connection.
Can't vape Smok vape kit – how to do?
SMOK Vape Kit Can’t Vape – How to Do? Give a warning like NO ATOMIZER or CHECK ATOMIZER or NO COIL) Giving a like NO ATOMIZER or CHECK ATOMIZER... Output short circuit Remind of "OHMS TOO HIGH" or "OHMS TOO LOW" Identify the problem caused by...
Why is my vape saying no coil?
“Check Atomizer” or “No Atomizer” will appear when your vape mod or pod vape isn't reading your coil correctly. This can be due to the 510 connector not reading properly (where the tank screws onto the mod), the coil not making proper contact inside of the tank, or possibly a short.
Why is my new coil not working?
Check that your tank contains enough e-liquid to cover the airflow holes in the coil to avoid the coil drying out. If none of that worked: It's possible that you're taking too many puffs in quick succession which means that the coil doesn't have enough time to wick new liquid through before you take the next hit.
How do I reset my GeekVape?
Restore Factory Settings: When the device is turned off, press and hold "+" and "-" button at the same time, the screen will display firmware version number, and then press and hold fire button, "+" and "-" button all at the same time to restore factory settings, a prompt as "CONFIG RESET" will be displayed on screen ...
How do you reset the coil on Aegis legend?
GeekVape Legend 2 Menu Once in Output adjustment mode, you can scroll down to adjust coil resistance and reset puff count by pressing the fire button. Press and Hold Fire & + button – Brightness Up.
How long does it take for your lungs to heal from vaping?
After one to nine months: clear and deeper breathing gradually returns; you have less coughing and shortness of breath; you regain the ability to cough productively instead of hacking, which cleans your lungs and reduce your risk of infection.
How do I get my vape to work again?
The best way around this problem is to vape with one of your fingers around one of the inlet vents. This increases the airflow pressure and might get the sensors up and working again.
Why is my geek vape not hitting?
Geek Vape Aegis Solo Not Working If nothing happens when you attempt to use the Geek Vape Aegis Solo, it's likely that the battery is dead or that the device is locked. To unlock the device, press the fire button five times quickly. If the device still doesn't work, try charging the battery.
How do you change a Geekvape coil?
2:035:30How to replace a geekvape cerberus coil. - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you grab the bottom of the tank. And the top of the tank. And you just twist counterclockwise.MoreAnd you grab the bottom of the tank. And the top of the tank. And you just twist counterclockwise. The whole tank should come apart. So you pull the top off and then you can grab your glass.
Why isn't my geek bar working?
A Common issue specifically with the Puff Bar/Beco Bar is that it stops hitting after using it for a few hours. This can be due to the cotton filter blocking the intake hole. Due to the rectangular build of the Puff/Beco bars, the mouthpiece can be taken off with the sharp end of some scissors or some tweezers.
How do you prime a vape coil?
To prime a new coil, simply fill your tank with e liquid and leave it to stand for a few minutes before vaping. As above, this will allow the cotton inside your new coil to absorb plenty of e-liquid ready for that first, tasty vape.
How do I fix no atomizer?
RecapClean all contacts on battery/mod, tank or pod.Remove and reinstall the coil (after cleaning)Try a new coil.Check the 510 pin and see if you can adjust it (mods/tanks)Try another tank on your mod.Try another mod with your tank.Adjust base of coil carefully if you can (mainly sub-Ohm coils)
How do you fix Aegis geek vape?
How to Fix Problems With the Geek Vape Aegis SoloTry a different USB cable. ... Try a different computer or a different USB port on the same computer. ... Make sure that the battery is secure and installed with the correct orientation. ... Replace the battery if none of the above solutions work.
What is the guide to vaping?
Guide To Vaping is the largest online magazine blog that is dedicated to providing a vast selection of helpful and informative articles about the latest vaping news, vapor products, and CBD.
What is the 510 pin on a circuit?
Make sure the connection points or coil leads are intact and seated properly. Sometimes the connection points will cross over to the opposing polarity. One lead is supposed to touch the positive side of the circuit, which is normally the 510 pin at the base, and the other isn’t supposed to be anywhere near it.
Is it rare for a manufacturer to release a product that is faulty?
Although quality control can often raise a concern with the non-stop outpour of products that make their way to the market , it’s very rare for a manufacturer to release a product that is faulty, especially since extensive testing is conducted by GeekVape before these products are set for release.
Is GeekVape a mod?
While GeekVape has a fascinating arsenal of products under its belt, including its popular Aegis Mod series, there are well more than a handful of GeekVape customers that are disgruntled due to a problem that is becoming consistent throughout the series.
How to tell if a vape is malfunctioning?
One easy way to know if your atomizer is malfunctioning is if your vape displays one of the following messages: check atomizer, no atomizer, or no atomizer found. If your vape shows one of these no atomizer messages, continue reading to find out how to proceed.
Why is my vape not recognizing my atomizer?
If your vape device isn’t recognizing your atomizer, it could be an issue as simple as an interrupted connection. Dust and debris can get in the way of the electrical current, leading to a complete mechanical failure. Other culprits can include an atomizer that’s completely screwed in, or a center pin that’s missing its mark. Take a close look at all the connection points on your device, clean them off, and make any adjustments to complete the current.
What is the pin on a vape?
The pin is the connection tip that’s found inside the 510 connector, responsible for making contact between your atomizer and vape device. If your pin is too low or too high, it can’t properly connect, and your device simply won’t work.
How to prevent vaping issues?
Take a Proactive Approach. Many vape issues can be avoided by simply performing regular cleanings and maintenance on your device. Taking proper care of your vape can help you minimize issues, and keep your vaporizer running in tip-top shape. Cleaning your vape isn’t difficult, and takes just a few moments of your day.
What tool to use to adjust vape pins?
However, if your vape isn’t one of these models, use a small tool, like a precision flathead screwdriver, to adjust the pin position ever-so-slightly.
How long does it take to read a vaporizer?
Reading Time: 4 minutes . Your vaporizer is a lot like your car: you count on it on a daily basis, it’s a critical part of your everyday routine, and you hope to avoid issues at all costs. However, just like a vehicle, vaporizers do run into mechanical problems every now and then.
What is a vaporizer?
A vaporizer is an electronic device, containing a battery that creates a very real electrical current. Above all, your safety should be your top priority. It’s easy enough to get a new atomizer or vape if yours has turned into a dud, but recovering from an injury that resulted from an overconfident, uninformed repair attempt is a much larger order.
What to do if your pod vape isn't firing?
If your pod vape isn’t firing, has a blinking LED and won’t fire, or says Check Atomizer or No Atomizer, you can follow a few of the same steps listed above for tanks: 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points.
How to clean a pod from a vape?
Also check inside your vape where the pod attaches to it. If you see any ejuice or dirt, clean it out with a paper towel then reinsert the pod and try again.
What to do if cleaning contact points doesn't fix check atomizer error?
If cleaning the contact points doesn’t fix the check atomizer error on your pod vape, you’ll want to carefully examine the contact pins/plates on your pod vape and on your pod for damage.
Why won't my 510 mod work?
Simply put, if your mod can’t read your tank and coil resistance properly, it won’t be able to deliver power and therefore won’t work.
What causes a check atomizer short?
Loose pieces of metal on the build deck will cause your mod to display “Check Atomizer” or “Atomizer Short”. Even very small pieces or trimmings of wire can cause a short or a check atomizer error on an RDA/RTA/RDTA. First, inspect the build deck closely for loose pieces of wire or other foreign objects.
What is a versed vaper?
The Versed Vaper team are a group of passionate and experienced vapers who take pride in writing helpful, quality content about vaping. From deals, to news and reviews, we've got you covered on all things vaping. Remember to subscribe to our newsletter, and follow us on Twitter, Instagram, and Facebook!
Why is my mod reading the new tank correctly?
If your mod is reading the new tank correctly, it could be a problem with the coil on your other tank. You might also want to clean the contact points on the tank that was giving you the error. If your mod is still reading “check atomizer” with a new tank, it’s probably a problem with your mod.
What does it mean when an e-cigarette says no atomizer?
An e-cig that says ‘no atomizer’ or ‘check atomizer’ is a message that no vaper wants to see. A source of frustration because this message flashing up on your vape mod most probably means that you cannot vape.
How to get vape juice out of a tank?
Take the base of your tank off. Take care if it is full of fluid and make sure you can remove the base without the tank leaking. If not decant the vape juice out of the tank first. Now check that your coil is screwed into the base of the tank correctly.
What does it mean when your tank is sat flush with a rubber o-ring?
If you have over tightened your tank onto your mod, it can push the metal plate from the 510 connection up into the tank. This usually means that it is sat flush with a rubber o-ring. If this is the case then it won’t make a full connection to your e-cig.
How to get a tank to pop back into the correct position?
Take your tank off your mod and turn it off, or remove the battery. Then take something small, like a small screwdriver and very gently press down on the pin. You should feel the spring underneath and this can get it to pop back into the correct position. Try attaching your tank again and see if the message has gone.
Can a mod make a complete connection to a vape tank?
Over time the connection on your e-cig can gather dust, dirt and e-liquid. If this is the case and your mod can’t make a complete connection to your vape tank, then this message will display. Remove your tank from your e-cig and have a look at the threads and metal plate to make sure there are no larger pieces of debris there.
