The No Coil Detected Check List
- Inspect the connection on your tank and make sure it doesn’t look disturbed or different than normal.
- Use alcohol and clean the bottom connection to ensure there isn’t any debris that could prevent a solid connection.
- Inspect the bottom pin on your tanks 510 connection to ensure that it’s protruding enough to make a solid connection.
Why does my vape tank say no coil detected?
The Tank: A lot of the times a No Coil Detected warning isn’t arising due to the mod, it’s because of the tank or atomizer. Even though the mod may have a spring-loaded center pin within the connector, the tank’s 510 threaded connector may not be making contact with that center pin.
What does “no coil detected” mean?
You may very well see a No Coil Detected warning on your device, and it’s possible that it isn’t a problem with your mod, it isn’t a problem with your tank, but instead a problem with the coil head. You see, this No Coil Detected warning is all about a connection issue, so somewhere there are two pieces that aren’t making a solid connection.
Can't vape Smok vape kit – how to do?
SMOK Vape Kit Can’t Vape – How to Do? Give a warning like NO ATOMIZER or CHECK ATOMIZER or NO COIL) Giving a like NO ATOMIZER or CHECK ATOMIZER... Output short circuit Remind of "OHMS TOO HIGH" or "OHMS TOO LOW" Identify the problem caused by...
Why does my geekvape aegis legend say no coil detected?
The Mod: In many cases, it is indeed the mod that causes the No Coil Detected warning. However, with devices like the GeekVape Aegis Legend, it’s a very seldom occurrence. The reason why is because the Aegis Legend has a Spring-Loaded Gold Plated 510 Connection, meaning the center pin will remain at its highest position until it’s pressed in.
What does it mean when my vape says no coil detected?
“Check Atomizer” or “No Atomizer” will appear when your vape mod or pod vape isn't reading your coil correctly. This can be due to the 510 connector not reading properly (where the tank screws onto the mod), the coil not making proper contact inside of the tank, or possibly a short.
Why is my coil not working?
Check your tank to make sure you have enough e-liquid. If your tank is completely full but you still have weak vapor, it is possible that your atomizer or coil has been flooded. If this happens, simply take your atomizer apart and clean it with a paper towel or gently blow through it to get the excess liquid out.
How do I reset my aegis vape?
Restore factory settings: Turn off power, press "+" and "-" button at the same time, the screen displays version number,press fire button "+" and "-"button at the same time, the screen displays "Config Reset" to restore factory settings.
How do you reset the coil on Aegis legend?
GeekVape Legend 2 Menu Once in Output adjustment mode, you can scroll down to adjust coil resistance and reset puff count by pressing the fire button. Press and Hold Fire & + button – Brightness Up.
How do you clean a vape coil?
How to clean your CoilLet your coil soak in ethanol, vinegar, or cheap vodka for at least a couple of hours.Place it under the tap and rinse.Rinse once more with some distilled water.Blow air on the open side of your coil to force water to the wicking holes.Set it aside until all water has evaporated.
How do I reset my Smok vape?
0:000:31How To Do A Factory Reset on Your IQC Vaporizer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce the reset is complete the vaporizer will vibrate and button lights will. Turn. Off you.MoreOnce the reset is complete the vaporizer will vibrate and button lights will. Turn. Off you.
Why does my geek vape say no atomizer?
When you get the “No atomizer” or “Check atomizer” message, it means your mod doesn't think your tank – or more specifically, your coil or atomizer head – is attached to the connection point. You'll see the same message when you try to fire a mod without anything attached.
Why is my geek vape flashing red?
If the red light flashes 3 times, it means that there is no atomizer connected, please change another pod or replace the coil and try again. 2. If the red light flashes 5 times, it means the battery is too low, please charge the battery full and try again.
How do I update my vape firmware?
To install a firmware update for your vape mod, visit the manufacturer's website. In the support section for your device, you'll find the application that's used for updating the firmware. You'll need to download that application and run it on your computer.
Is it OK to charge aegis legend with USB?
One thing that we recommend to ensure that you get the best protection from your Aegis Legend is to rarely if ever use the micro USB charge port, this is for a few reasons. First and foremost, the charge port is protected by a rubber gasket.
How do I unlock my geek vape?
If your Geek Vape Aegis Hero isn't hitting when you hold the fire button, you should first check to confirm that you haven't locked the device. Press the fire button five times to unlock it.
How do you check if a coil is bad?
0:111:32How To Diagnose Bad Coil Pack. NO TOOLS! - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut let's say you unplug this one right here and it does absolutely nothing to the runningMoreBut let's say you unplug this one right here and it does absolutely nothing to the running characteristics of the motor. Like it act like it didn't do anything or it didn't care you unplugged.
What are the symptoms of a failing coil pack?
Common Symptoms of a Faulty Coil PackA rough idle.An unexplainably louder-than-usual engine.A noticeable lack of power.A significant drop in RPMs while accelerating for no apparent reason.A blinking or intermittently activating check engine light.An active gas warning light when the vehicle has plenty of gasoline.More items...
How do you test a coil?
1:055:53How to Test Ignition Coils - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou connect the leads to the positive in the output wire. And the reading should be anywhere fromMoreYou connect the leads to the positive in the output wire. And the reading should be anywhere from 6,000 to $15,000.
Why is my car misfiring after changing spark plugs and coils?
If your car misfires after you changed the spark plugs and coils, it's likely due to another problem. Other possible causes include a clogged fuel injector, low compression, or a problem with the computer that controls the ignition system. If you're not sure what's causing the problem, have your mechanic check it out.
Why is my mod not finding coil?
The Tank: A lot of the times a No Coil Detected warning isn’t arising due to the mod, it’s because of the tank or atomizer. Even though the mod may have a spring-loaded center pin within the connector, the tank’s 510 threaded connector may not be making contact with that center pin. This can happen for several reasons, such as the 510 connection not being long enough, the tank not being screwed in enough, the pin on the tanks connector not protruding enough from the connector, or a simple case of there being grime and debris that has lodged its way into the connector, preventing the two parts to making a solid connection.
What is the 510 pin on a circuit?
Make sure the connection points or coil leads are intact and seated properly. Sometimes the connection points will cross over to the opposing polarity. One lead is supposed to touch the positive side of the circuit, which is normally the 510 pin at the base, and the other isn’t supposed to be anywhere near it.
Why is the Aegis Legend pin at its highest position?
The reason why is because the Aegis Legend has a Spring-Loaded Gold Plated 510 Connection, meaning the center pin will remain at its highest position until it’s pressed in. When you receive the No Coil Detected warning and it’s an issue related to the mod, it’s often an issue with the center pin in the 510 connector.
What is the guide to vaping?
Guide To Vaping is the largest online magazine blog that is dedicated to providing a vast selection of helpful and informative articles about the latest vaping news, vapor products, and CBD.
How to clean a solid connection?
Use alcohol and clean the bottom connection to ensure there isn’t any debris that could prevent a solid connection.
Where to inspect tank coil?
Inspect the bottom base of the tank, where the coil makes a connection to the base, and make sure the area hasn’t been disturbed.
Is GeekVape a mod?
While GeekVape has a fascinating arsenal of products under its belt, including its popular Aegis Mod series, there are well more than a handful of GeekVape customers that are disgruntled due to a problem that is becoming consistent throughout the series.
What is the guide to vaping?
Guide To Vaping is the largest online magazine blog that is dedicated to providing a vast selection of helpful and informative articles about the latest vaping news, vapor products, and CBD.
How to prevent a short in an atomizer?
Make sure that you have no debris inside the coil housing. Something as simple as a piece of plastic could prevent a solid connection and cause an atomizer short. Get into the habit of checking it and wiping out the area every time you open up the tank.
Can you use an Ohm reader on a tank base?
Even with pre-made coils and tank bases I would suggest using an Ohm reader, just to check if the coil is reading right . it is much easier to figure out what is wrong with your set-up before you fill it with e-liquid.
Is a coil reader expensive?
They’ re not expensive and can help you out with much more than just figuring out the wattage range of the coil. If you put a coil on a reader, even if it’s the one built-in to your mod and it reads anything other than what you expect, it may have a problem.
AegiSolCube New Member
I am using the tank from my obs cube which work fine on the obs cube with my Aegis Solo.
UncleJunkle Vaping Master Verified Member ECF Veteran
Please try another atomizer that is working fine in your other mods, and check if you have built the coils correctly.
UncleJunkle Vaping Master Verified Member ECF Veteran
Personally, I believe the Solos have positive 510 pins that sit a hair lower than most other mods and/or the 510 spring on them gets fatigued over a short time causing atomizer that once connected to not connect anymore.
Bronze ECF Guru Verified Member ECF Veteran
The paint wore down on the plastic trim piece that surrounds the leather portion. Removed and repainted it. The actual color is darker than the photo. More of a cranberry color (muddy red). Doesn't stand out as much as the photo suggests. Rust Oleum Colonial Red.
What causes a vape atomizer to fail?
The center pins can easily cause apparent atomizer failure, particularly when they’re misplaced. The pin is the connection tip that’s found inside the 510 connector, responsible for making contact between your atomizer and vape device. If your pin is too low or too high, it can’t properly connect, and your device simply won’t work.
How to tell if a vape is malfunctioning?
One easy way to know if your atomizer is malfunctioning is if your vape displays one of the following messages: check atomizer, no atomizer, or no atomizer found. If your vape shows one of these no atomizer messages, continue reading to find out how to proceed.
What is the pin on a vape?
The pin is the connection tip that’s found inside the 510 connector, responsible for making contact between your atomizer and vape device. If your pin is too low or too high, it can’t properly connect, and your device simply won’t work.
Why is my vape not recognizing my atomizer?
If your vape device isn’t recognizing your atomizer, it could be an issue as simple as an interrupted connection. Dust and debris can get in the way of the electrical current, leading to a complete mechanical failure. Other culprits can include an atomizer that’s completely screwed in, or a center pin that’s missing its mark. Take a close look at all the connection points on your device, clean them off, and make any adjustments to complete the current.
What is a vaporizer?
A vaporizer is an electronic device, containing a battery that creates a very real electrical current. Above all, your safety should be your top priority. It’s easy enough to get a new atomizer or vape if yours has turned into a dud, but recovering from an injury that resulted from an overconfident, uninformed repair attempt is a much larger order.
How to prevent vaping issues?
Take a Proactive Approach. Many vape issues can be avoided by simply performing regular cleanings and maintenance on your device. Taking proper care of your vape can help you minimize issues, and keep your vaporizer running in tip-top shape. Cleaning your vape isn’t difficult, and takes just a few moments of your day.
What tool to use to adjust vape pins?
However, if your vape isn’t one of these models, use a small tool, like a precision flathead screwdriver, to adjust the pin position ever-so-slightly.
What is a geekvape?
Geekvape aims to provide the best quality experience to the e-cigarette users across the world. Welcome here, please feel free to share anything relating to e-cigarette with us.
Does changing coils clear it?
Either that, or Ive had a lot of dud coils right out of the box (I work at a vape shop) and it'll throw this message. Usually changing it clears it, and it works fine. I assume you've already tried a different coil, and I know you said you've tried different tanks.
