SMOK Ohms Too High or Too Low Error messages about ohms are specifically related to the resistance of your coil (s) and indicate that a coil is not compatible with the device. Typically, pairing the proper SMOK-branded coils with your SMOK device is the easiest way to fix this problem.
Why is my vape giving me a “ohms too low” warning?
Apr 23, 2018 · Please take off the tank and click the fire button, and then place that tank back on, click "n" when it asks "is it a new coil". Please make sure screws are tight on the tank if you use the RBA coil on your mod. Please try with other tanks or coils on your mod, and try the same tank on the other mods to check whether they work fine. < PREVIOUS
What do you do when your vape says Max puff?
1. Please take off the tank and click the fire button, and then place that tank back on, click "n" when it asks "is it a new coil". 2. Please make sure screws are tight on the tank if you use the RBA coil on your mod. 3. Please try with other tanks or coils on your mod, and try the same tank on the other mods to check whether they work fine. 4.
What should I do if my Smok vape won't turn on?
Your coils are probably fucked making your device read too high. Change them out and try with a fresh coil. 2. level 1. Op · 4 yr. ago. Okay, I tried to swap out my coil for a premade one and now it's saying 0.0 ohms. It does work with baby beast tank though. 1.
Why is my resistance detection not working on my vape?
Your mod can't read the resistance correctly, show "ohms too low" or "ohms too high" It may be caused by these points: 1. There's a breakdown for the resistance detection component. 2. Tank screws are not tight down to the mod. 3. Loose contact for the tank or …
What does it mean when the ohm is too high on a vape?
Can you adjust ohms on a vape?
Is it better to have higher ohms or lower vape?
Why does my coil keep changing ohms?
How do I lower my ohms?
How do you fix ohms too high SMOK?
...
You could try the following methods to recover:
- Please take off the tank and click the fire button, and then place that tank back on, click "n" when it asks "is it a new coil".
- Please make sure screws are tight on the tank if you use the RBA coil on your mod.
What wattage should I vape at 0.17 ohm?
What wattage should I vape at 0.20 ohm?
What wattage should I vape at 1.0 ohms?
How many ohms should my vape be?
What wattage should I vape at 0.15 ohm?
How many wraps Should a coil have?
KurtVD Super Member ECF Veteran
I've built a nice coil with 28Ga SS316L wire, and due to the thin wire and the large deck of my RDA (about 8 oder 9 wraps needed to fill the space), the resistance at room temperature was over 1.7 Ohm. When I wanted to test fire it with 30 Watts (in my Pico 75), the display showed "Ohms too high" (it quickly climbed to 2.5 Ohm, I think).
sonicbomb Vaping Master Verified Member ECF Veteran
In power mode the maximum resistance on your mod is 3.5 ohms, in TC mod it's 1.5 ohms. SS will increase in resistance as it heats.
Foggy Road Vaping Master Verified Member ECF Veteran
First problem... Sounds like you're in TC mode? Pico won't fire over 1.5 ohm in TC mode, you'll have to change to wattage. Your coils were probably fine.
tailland Ultra Member ECF Veteran
Maybe you're running into a consequence of Ohm's law that is usually ignored when talking about regulated mods: Insufficient voltage.
ShamrockPat Ultra Member ECF Veteran
You've got a whole bunch of 'things' all going on at the same time. Ohms law and the constraints of your mod will dictate what will occur. Dunno about your Pico, so I'll mention your DNA75, where the vendor publishes their specs. It has a 6.2V maximum output voltage.
DaveP PV Master & Musician ECF Veteran
Try 10 wraps 28 gauge SS316L with a 2.5mm diameter coil. You'll be around 1 ohm and that should be fine. Install two of those for a dual setup and you'll be at .5 ohms, which is also a safe range for battery life.
Foggy Road Vaping Master Verified Member ECF Veteran
You've got a whole bunch of 'things' all going on at the same time. Ohms law and the constraints of your mod will dictate what will occur. Dunno about your Pico, so I'll mention your DNA75, where the vendor publishes their specs. It has a 6.2V maximum output voltage.
Why is my vape ohm error?
Or, you may need to tighten the screws properly. Other reasons you may see an ohm error include: The resistance detection component of your device is broken. A failing resistance detection component is a serious problem with the device itself and might mean it’s time to find a new vape.
What is the best brand of vape?
There’s no doubt that SMOK is one of the vape industry’s best brands, crafting top-of-the-line mods and pod systems like the SMOK Nord, SMOK Morph, SMOK NOVO, and so many more.
How to fix a coil that tastes burnt?
Here are a few suggestions for how to fix coils that taste burnt: Replace your coils when needed. Expect to replace coils every few weeks or so (or about 50mL of e-juice, according to SMOK guidelines). Burnt-tasting coils are usually the first sign that it’s time to switch them out for new ones.