what to do if my vape says no atomizer

How do I fix my vape when it says no atomizer?

• Clean all contacts on battery/mod, tank or pod.
• Remove and reinstall the coil (after cleaning)
• Try a new coil.
• Check the 510 pin and see if you can adjust it (mods/tanks)
• Try another tank on your mod.
• Try another mod with your tank.
• Adjust base of coil carefully if you can (mainly sub-Ohm coils)

Full Answer

Why does my vape Say No atomizer?

An e-cig that says ‘no atomizer’ or ‘check atomizer’ is a message that no vaper wants to see. A source of frustration because this message flashing up on your vape mod most probably means that you cannot vape. If playback doesn't begin shortly, try restarting your device.

How to fix check atomizer on a pod vape?

How to Fix Check Atomizer/No Atomizer On A Pod Vape. 1 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points. 2 2. Check Your Contact Points for Damage. 3 3. Reseat your Coil/Pod. 4 4. Try Another Coil/Pod.

What to do when your vape won’t fire?

Clean Your Contact Points The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points. Take the pod out of your pod vape and check the bottom of the pod for any dirt or ejuice. Also check inside your vape where the pod attaches to it.

How to clean a vaporizer properly?

Make a habit of using a clean, damp cloth to wipe down the vaporizer, paying special attention to small crevices and connection points. A cotton swab can be an excellent way to gently reach even the tiniest of spaces, where gunk and grime like to hang out.

What to do if your pod vape isn't firing?

If your pod vape isn’t firing, has a blinking LED and won’t fire, or says Check Atomizer or No Atomizer, you can follow a few of the same steps listed above for tanks: 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points.

How to clean a pod from a vape?

Also check inside your vape where the pod attaches to it. If you see any ejuice or dirt, clean it out with a paper towel then reinsert the pod and try again.

What to do if cleaning contact points doesn't fix check atomizer error?

If cleaning the contact points doesn’t fix the check atomizer error on your pod vape, you’ll want to carefully examine the contact pins/plates on your pod vape and on your pod for damage.

Why won't my 510 mod work?

Simply put, if your mod can’t read your tank and coil resistance properly, it won’t be able to deliver power and therefore won’t work.

How to clean a tank after taking apart?

Once you’ve taken apart your tank, unscrew your coil from the base of the tank. Now, you’ll want to clean the bottom of the coil where it screws into the tank and makes contact. You’ll also want to clean your tanks contact point with the mod as well. Once done, reseat your coil, and reassemble your tank.

What causes a check atomizer short?

Loose pieces of metal on the build deck will cause your mod to display “Check Atomizer” or “Atomizer Short”. Even very small pieces or trimmings of wire can cause a short or a check atomizer error on an RDA/RTA/RDTA. First, inspect the build deck closely for loose pieces of wire or other foreign objects.

What is a versed vaper?

The Versed Vaper team are a group of passionate and experienced vapers who take pride in writing helpful, quality content about vaping. From deals, to news and reviews, we've got you covered on all things vaping. Remember to subscribe to our newsletter, and follow us on Twitter, Instagram, and Facebook!

Why is my vape not recognizing my atomizer?

If your vape device isn’t recognizing your atomizer, it could be an issue as simple as an interrupted connection. Dust and debris can get in the way of the electrical current, leading to a complete mechanical failure. Other culprits can include an atomizer that’s completely screwed in, or a center pin that’s missing its mark. Take a close look at all the connection points on your device, clean them off, and make any adjustments to complete the current.

How to prevent vaping issues?

Take a Proactive Approach. Many vape issues can be avoided by simply performing regular cleanings and maintenance on your device. Taking proper care of your vape can help you minimize issues, and keep your vaporizer running in tip-top shape. Cleaning your vape isn’t difficult, and takes just a few moments of your day.

How to tell if a vape is malfunctioning?

One easy way to know if your atomizer is malfunctioning is if your vape displays one of the following messages: check atomizer, no atomizer, or no atomizer found. If your vape shows one of these no atomizer messages, continue reading to find out how to proceed.

What is a vaporizer?

A vaporizer is an electronic device, containing a battery that creates a very real electrical current. Above all, your safety should be your top priority. It’s easy enough to get a new atomizer or vape if yours has turned into a dud, but recovering from an injury that resulted from an overconfident, uninformed repair attempt is a much larger order.

What tool to use to adjust vape pins?

However, if your vape isn’t one of these models, use a small tool, like a precision flathead screwdriver, to adjust the pin position ever-so-slightly.

How long does it take to read a vaporizer?

Reading Time: 4 minutes . Your vaporizer is a lot like your car: you count on it on a daily basis, it’s a critical part of your everyday routine, and you hope to avoid issues at all costs. However, just like a vehicle, vaporizers do run into mechanical problems every now and then.

What is the pin on a vape?

The pin is the connection tip that’s found inside the 510 connector, responsible for making contact between your atomizer and vape device. If your pin is too low or too high, it can’t properly connect, and your device simply won’t work.

What does it mean when an e-cigarette says no atomizer?

An e-cig that says ‘no atomizer’ or ‘check atomizer’ is a message that no vaper wants to see. A source of frustration because this message flashing up on your vape mod most probably means that you cannot vape.

How to get vape juice out of a tank?

Take the base of your tank off. Take care if it is full of fluid and make sure you can remove the base without the tank leaking. If not decant the vape juice out of the tank first. Now check that your coil is screwed into the base of the tank correctly.

What does it mean when your tank is sat flush with a rubber o-ring?

If you have over tightened your tank onto your mod, it can push the metal plate from the 510 connection up into the tank. This usually means that it is sat flush with a rubber o-ring. If this is the case then it won’t make a full connection to your e-cig.

How to get a tank to pop back into the correct position?

Take your tank off your mod and turn it off, or remove the battery. Then take something small, like a small screwdriver and very gently press down on the pin. You should feel the spring underneath and this can get it to pop back into the correct position. Try attaching your tank again and see if the message has gone.

Can a mod make a complete connection to a vape tank?

Over time the connection on your e-cig can gather dust, dirt and e-liquid. If this is the case and your mod can’t make a complete connection to your vape tank, then this message will display. Remove your tank from your e-cig and have a look at the threads and metal plate to make sure there are no larger pieces of debris there.

Why do vapers forget atomizer error messages?

They were added by the manufacturer to protect you from faulty atomizers, and to prevent firing mishaps that can cause damage or injury.

Why does my mod say no atomizer?

However, once you put your top cap on, the sides are touching the coil (usually because it’s either too large or protrudes to one side too much), and that causes your mod to show you a “no atomizer” or “short atomizer” error message.

What does it mean when your chipset says no atomizer?

When your chipset is responsible for an “atomizer short “or a “no atomizer” error message, it means that it’s preventing firing on the basest of levels. There’s nothing here that you can fiddle with or adjust to fix this.

Why does my vape pen leak?

There’s vape juice in your vape pen – leaky atomizers are damaged atomizers. When juice seeps into your circuitry, it can damage it and cause it to show error messages when there’s actually nothing wrong with the atomizer.

What to do if you don't have an external charger for your vape?

If you do not have an external charger, then you will need to rely on your vape mod to identify the issue with your atomizer. If the batteries are the issue then either find the right coil resistance for the batteries (if they are not defective) and device being used or get a new pair of batteries.

What are the problems with vaping atomizers?

The three most common atomizer problems are: Atomizer short warning. Atomizer low warning. No atomizer found warning. Those are the warnings that will typically pop up when you run into issues with the coil.

What does it mean when your coil is low?

The coil is too low in resistance in the mod thus displaying the "atomizer low" message. blockquote An atomizer low warning means that the device does not support the atomizer's resistance. This means that your atomizer's resistance is too low and is thus not compatible with your mod.

Why is there no atomizer found?

If the warning is still there after trying to fix it then it could be an issue with the mod being used. A "no atomizer" warning almost always means the coil being used is dead or loosely seated .

What is a RTA atomizer?

It can refer to devices containing coils or it's also used to refer to the coil inside the device. There are three types of atomizer devices: vape tanks , rebuildable drip atomizers (RDA), and rebuildable tank atomizers (RTA). These devices all use a coil that heats up and transforms vape juice into vapor.

Why does my atomizer give me a short message?

There could be a number of reasons why your device is giving you a short message. If you are using a rebuildable atomizer then your coil could be touching an unintended area like the deck or cap of the casing. If you are using a tank with a pre-built coil then the coil can either be defective or it could be loose.

How to fix an atomizer short?

How to fix an "Atomizer short" warning: Place batteries on an external charger to ensure they're both charging properly. For rebuildable atomizer users (RDA/RTA), make sure the coil is not touching the cap or deck and contains no breaks in your coil.