What is the difference between TCR and TFR?
For TCR the "TC in vaping range" is what you want to use for TCR. You have to do the math to get the decimal number you need. For TFR you just enter in the number for each temperature that it presents you on the 213 from the steam engine wire wizard. They tried to make it like how you program DNA devices. But to me it's actually easier!
What does TCR mean on a vape device?
It is the basis of all temperature control vaping. Props to Evolv for coming up with that sorcery. A TFR (Temperature Factor of Resistance) is similar to TCR, but is based on actual observed measurements rather than pure mathematics.
What are temporary flight restrictions (TFRs)?
· Based on the TFR test results, we’d suggest using the following values depending on the format the mod is expecting: NifFe30 : 4920 or 492. 316L : 883 or 88. Ni200 : 6230 or 623. Wires like Kanthal A1 and Nichrome 80 / Ni80 have a very low TCR, so don’t work in temperature control mode. Evolv DNA250C boards are able to use the Replay ...
What is the temperature limit on a vape?
· My Reuleaux RX200 and Vapor Flask Classic seem to use the same value for their TCR. My iPV5 uses a completely different value and I just got the Sigelei 213 and its also completely different. What I'm trying to do in this thread is create a simple guide on how to determine the correct TCR or TFR(if applicable) for all of the different chips in ...
What is TC mode vape?
Temperature control (TC) in vape mods is a technological solution for dry and burnt hits. It also creates a consistent vape while taking longer drags because the temp stays the same—instead of getting hotter. The user chooses the temperature limit, typically from a range of 300°F to 600°F (100°C to 315°C).
What setting should my vape be on?
As a general rule, dab temperatures are set between 315℉ to 900℉. Below 315℉ is usually too low to vaporize cannabis concentrates. And above 900℉ can release carcinogens as well as a harsh, burnt vapor.
What does TC NI mean?
First Time Temperature Control Setup: Depending on your vaporizer, it may have a single TC Vape Mode that supports both Nickel (Ni) and Titanium (Ti) coils, or it may have a specific Temperature Control Mode that must be set to support either Nickel (Ni) or Titanium (Ti) coils individually.
What is SS mode vape?
Stainless Steel Mode (SS Mode) It shares nickel and titanium's fast ramp-up speed, but does not oxidize when dry burned, giving you more ability to adjust your coils when they're heated. Stainless steel is also not known to cause any adverse allergic reactions.
What wattage gives the best flavor?
The sweet spot for getting a balance of vapour and flavour is around 0.3ohms. Depending on your coil choice you'll want to up the wattage from anywhere between 50 and 100 watts.
What is the best wattage to vape at?
On the contrary, even 10 watts is sufficient to guarantee a satisfying vape, which may be ideal for new vapers. As you become more experienced, it's safe to say that vaping starts to shine between the range of 40 and 50 watts.
What does SS Ni and Ti mean on my vape?
Stainless steel (SS), nickel (NI), and TI (titanium) are all wire materials. With the exception of stainless steel, which can be used in wattage mode and SS mode, they should only be used in those mods that correspond to them. They allow you to limit the temperature you vape at.
What temperature should I vape Indica?
To get maximum medical benefit from cannabis, vape your indica or sativa at 430° to consume as much CBD and CBD cannabinoids as you can. Medicinal terpenes linalool and humulene are well suited to vaping just below the 451 degrees combustion point. Of course, you can vape hybrid weed at this temperature.
Can you use kanthal in TC mode?
Ni, Ti and SS coils are compliant with temperature control but not Kanthal. The reason why Kanthal does not allow temperature control is because this FeCrAl alloy has much more impurities than any others and does not offer superconductivity properties (a linear relationship of resistance with temperature).
What is VPC mode?
Variable Power Curve (VPC) is an advanced function or mode option on some mods. This mode enables the user to customize different power levels (wattage) in set increments, providing a power curve over a puff duration (time). VPC was first introduced about 3 years ago and was only found on a handful of high-end mods.
What is bypass mode?
Bypass mode is, by far, the simplest of advanced vaping modes. Removing wattage and voltage output, Bypass Mode allows the user to utilize the mod like a mechanical mod, designating output to correlate with the level of charge within the battery.
LPearce7 Full Member
If this topic has been covered on this forum, please let me know. I have not been able to find a good guide for this exact topic.
Tommy-Chi Ultra Member ECF Veteran
Thank you for the info! I have two Sigelei 213s, and I'll be buying a few more.
What does TCR mean in vaping?
Putting it simply, TCR denotes a number that identifies how the resistance of a material changes as the temperature fluctuates. When talking about vaping devices, the TCR refers to how the coil’s (material) resistance changes as the heat increases/decreases.
What is TCR mode?
To put it simply, the TCR mode allows you to adjust your mod to be as precise as possible, especially with the coils and materials that weren’t manufactured to work with your factory set mod. So, if you are experimenting with unique coils, use the TCR mode for safety purposes.
Why is TCR important?
Importance of TCR Mode. It is a known fact that not all materials (coil) respond the same when there is an increase in temperature. The type of alloy in coils is responsible for establishing the connection between resistance and potential heat.
What type of wire do you use for vaping?
Next, you must vape with the right wire type. TC vaping generally uses one of these four types of vape wires: Stainless steel: this wire is very popular and readily available. It comes in various grades such as 304, 316, 316L, 317, and 430 but the most common is SS316L. SS can be used in wattage or temperature control mode.
What is the best wire for vaping?
TC vaping generally uses one of these four types of vape wires: 1 Stainless steel: this wire is very popular and readily available. It comes in various grades such as 304, 316, 316L, 317, and 430 but the most common is SS316L. SS can be used in wattage or temperature control mode. 2 Nickel 200: commonly known as ni200, it was the first temperature control coil but it’s less common now due to some vapers having sensitivities to nickel. 3 Titanium Grade 1: otherwise known as Ti. It works well in TC but the user has to make sure it does not get overheated. 4 Nickel ferrous: also known as NiFe, comes in various grades such as 48, 30, 52, 70 and can be used in either mode, but is not widely available.
Can you adjust wattage on a vape mod?
Prior to TC, most top vape mods could only adjust watts (another innovation from Evolv a few years prior.) Now in 2020, like wattage control, temperature control is a feature found in most vape mods.
WHAT WE DO
TFR Distribution is the official retail and wholesale distributor for LFR and Troyer Race Cars brands.
STATE-OF-THE-ART FACILITIES
TFR Distribution, in addition to the extensive Parts Department and Showroom, also boasts the ability to build and support your entire race program. We offer complete professional services for:
TFR information
Pilots should obtain up-to-date information about TFRs from the FAA or flight service. Here are some quick links to official sources of TFR information.
Educational airspace resources
Brush up on your knowledge of airspace, including TFRs, download a kneeboard guide for intercept procedures, learn about requirements for flying through the outer ring of some TFRs, and see what it’s like to fly into the Washington, D.C., Flight Restricted Zone.
