The new Iolite Vapor Optimizer is designed to enhance vapor density by adding three additional heat pins to the heating chamber. This tool allows the heat to distribute more effectively in the bowl, providing more efficient and even vaporization. The optimizer does a great job of boosting the Iolite’s performance.
What to do if your vape says atomizer short?
If using an RDA/ RTA, check and see if the coil is touching the cap or deck. If error messages continue to pop up, use a different atomizer on the mod. If it still reads “atomizer short,” the problem is with the vape, not the atomizer or coil.
How to use a vape pen?
Once it is on, it’s ready for use. If your vape pen is button activated, simply hold down the button as you draw from the mouthpiece of your cartridge. You’ll want to make sure you vaporizer battery is charged before you get started.
Can you over-tighten a vape pen?
Over-tightening your vape pen can sever the connection between the battery and the cartridge. The 510 connection pin on the vape pen needs to connect with the cart to work. If you tighten the vape pen too hard, it can damage this important connection. Over-tightening can also break the rubber O-rings that seal the threading.
How do I Turn on a vaporizer pen?
Even if you are not new to vaping, we hope you find some helpful information along the way. To turn on a vaporizer pen, press the button 5 times rapidly. A light will typically appear or flash to indicate it is on.
What is an optimizer on a vape pen?
Product Description. This performance enhancing tool that is crafted to boost the vapor density by adding three additional heat pins in the heating chamber. The iolite Vaporizer Optimizer allows the heat to distribute evenly and effectively in the bowl, producing a more pure, smooth vaporization.
Why is my vape saying no Optimizer?
“Check Atomizer” or “No Atomizer” will appear when your vape mod or pod vape isn't reading your coil correctly. This can be due to the 510 connector not reading properly (where the tank screws onto the mod), the coil not making proper contact inside of the tank, or possibly a short.
What setting should I set my vape to?
As a general rule, dab temperatures are set between 315℉ to 900℉. Below 315℉ is usually too low to vaporize cannabis concentrates. And above 900℉ can release carcinogens as well as a harsh, burnt vapor.
What do you do when your vape says check atomizer?
RecapClean all contacts on battery/mod, tank or pod.Remove and reinstall the coil (after cleaning)Try a new coil.Check the 510 pin and see if you can adjust it (mods/tanks)Try another tank on your mod.Try another mod with your tank.Adjust base of coil carefully if you can (mainly sub-Ohm coils)
How do you fix a vape that won't smoke?
Check your tank to make sure you have enough e-liquid. If your tank is completely full but you still have weak vapor, it is possible that your atomizer or coil has been flooded. If this happens, simply take your atomizer apart and clean it with a paper towel or gently blow through it to get the excess liquid out.
Why does my vape taste burnt?
It tastes burnt because the wick inside your atomizer coil has dried out and burned up when it was heated. The wick is the part of your vaporizer that soaks up the eliquid from the tank. The wick holds onto this eliquid before it is turned into vapor when the coil heats up.
How do I get the best flavor out of my vape?
The 10 Best Ways to Enhance Vape Juice FlavoursChange Your Wattage and Temperature. Just like any reaction between heat and flavour, temperature affects how things taste. ... Avoid Vaper's Tongue. ... Proper E-Juice Storage. ... Limit Airflow. ... Get A Good Atomiser. ... Below-coil Airflow. ... Get a Narrow-bore Drip Tip. ... Keep Everything Clean.More items...•
What temp should vape be set at?
The most common vape temp is between 190 to 235 degrees Celsius (374 to 455°F).
What is the best wattage to vape at?
On the contrary, even 10 watts is sufficient to guarantee a satisfying vape, which may be ideal for new vapers. As you become more experienced, it's safe to say that vaping starts to shine between the range of 40 and 50 watts.
Is an atomizer a coil?
The coil is a small part in an electronic cigarette which gets hot. A coil head is also known as an atomizer head. These are words for the same thing, the heating element inside an e-cigarette.
How do you check an atomizer?
0:463:22How To Fix 'Check Atomizer' - YouTubeYouTubeStart of suggested clipEnd of suggested clipSometimes juice likes to sit in the 510 of the device. So make sure you give this a clean also ifMoreSometimes juice likes to sit in the 510 of the device. So make sure you give this a clean also if there is juice or dirt inside the 510. Then your device may not be able to read your tank or RDA.
How do you know if your atomizer is bad?
Signs it's time to change your vape coilA burning taste. Vaping a dead coil will eventually result in an acrid, burning taste. ... Gurgling sounds. Vapes shouldn't gurgle. ... Weak or “off” e-Juice flavor. This often precedes a burnt taste. ... Low vapor production. The vapor produced by your coil will gradually lessen with time.
How long does it take to learn to use a vape pen?
It won’t take longer than 5-minutes to learn how to use a vape pen, with a button or without one.
How many times does a vape pen battery turn on?
Typically, most vape pen batteries with a button turn on by clicking it 5 times. Most variable voltage 510-thread batteries will switch voltage settings by clicking it either 2 or 3 times rapidly. It's important to always read the vape pen instructions before using a new one.
What to do when your vape is not in use?
Tips for When Your Vape is Not in Use. Try to make it a habit to turn it off your vape pen battery when not in use, this will help preserve battery life and protect it from use by children. Also, always remove the THC vape cartridge from the battery when not using it too, this will help prevent possible damage.
What is a dab atomizer?
Dab - The mode meant for vaping cannabis extracts with a 510-thread wax atomizer, and is indicated with blue lights. It can also be used with THC cartridges that can take this voltage setting. But do not use this setting with any vape cartridge unless you're certain it's capable of vaping at this voltage.
What is the dab mode on a vape?
The settings ranging from low to high are all automatic draw activated puffs, but the dab mode (blue lights) requires you to hold down the power button during the inhale. The first three settings are perfect for those who want to vape without having to press a button, and will vape THC cartridges by simply inhaling.
How long does it take for a vape puff to stop heating?
This means the pen will stop heating the cartridge after a certain amount of time. Most pens will have this occur around 8-seconds.
Can you vape with a 510 atomizer?
The O.pen has evolved into the 2.0 version with multiple temperature settings, including a dab mode. So, you can enjoy vaping your favorite cannabis extracts with your choice of 510-thread wax atomizer. There are many aspects to consider when purchasing a vape pen battery.
How to use a vape pen?
The first thing you’ll need to do before using your vape pen is to make sure it’s charged. Open up the box and plug it into the charger as soon as possible, and you’ll be ready to start vaping in no time. If your pen has a tank, you’ll need to open it up and fill it with vape juice.
What is a vape pen?
As you’ve probably already guessed based on the name, a vape pen is a pen-shaped vaporizer device. Compact and cylindrical, a pen-style vape is a highly portable device option that’s ideal for discreet, on-the-go vaping. The size of a vape pen may be as slim as a regular pen or as large as a cigar.
What to do if you don't have a button on your vape pen?
If there’s no button on your vape pen, it’s likely draw-activated. In this case, you’ll place your mouth on the mouthpiece and take a gentle, steady breath to turn it on. When in doubt, one of the most important things you can do is refer to your device instructions.
What is a vape pen charger?
Charger: Every vape pen comes with a charger, whether it’s a USB, car, or wall charger. Just like a phone charger, your vape charger plugs into the device and then into a power source to recharge the battery.
What is the heating element in a vape pen?
Atomizer. The atomizer is the vape pen’s heating element, used to heat the e-liquid to the point of vaporization. Designed in a variety of coil structures, your vape’s heating element is key to the overall vape experience.
What type of battery does a vape pen use?
Like any electronic device, a vape pen requires a battery to run. Vape pens are typically powered by lithium-ion batteries, with a variety of options available. When you’re browsing vape pens, you’ll usually see batteries assigned a numerical value labeled with the unit mAh.
Why do people use vape pens?
Another reason so many vapers use vape pens as their device of choice is that they are extremely easy to clean and maintain. Developing good habits when it comes to the care of your device can not only extend the life of your vape pen but also ensure an excellent vape experience every time.
Cannabis oil has high viscosity and the concentrate may become stiff. When cannabis oil is cold or settled to one side of the cartridge, it may fail to flow correctly. To fix this, apply heat to the cart. Heating up the cart lowers the viscosity of the cannabis oil, which allows it to flow when you pull
A common solution for freeing up your settled cannabis oil involves using a hairdryer to heat the cart. Separate the cart from the battery and set the cart upright. On its low setting, hold a hairdryer about six inches away from the cart. Apply heat for about 30 seconds. When you see bubbles forming, let the cart sit for a few seconds.
Oil amounts appear low in cartridges
Sometimes when you purchase a vape cartridge, the oil level looks much lower than you thought it would be. If your oil level looks low, it could mean your oil has settled on one side. To resolve this problem, apply heat to the sides of the cart with a hair dryer method mentioned above and check to see if the oil level appears higher than it was.
What does low atomizer mean?
Atomizer Low means that the coil resistance is too low. Vapers who see any of these messages on their mod should stop using the vape immediately. But do not worry. These issues can be solved quickly so that the user can get back to vaping as soon as possible.
Why is my atomizer low?
A common reason why the atomizer low warning occurs during vaping is that the coil was not properly made, the connection is loose, it is not seated correctly, or it does not have an insulator. Another reason a user might get this warning is that he or she misjudged the size of the build.
Why won't my vape fire?
If the resistance of the coil is lower than what the device can tolerate , the vape will not fire. Dry burning is one way to get around this problem because it can raise the coil’s resistance. Another thing to do is add wraps to the coil, which will increase the resistance high enough so that the mod fires.
How to turn on a vaporizer pen?
To turn on a vaporizer pen, press the button 5 times rapidly. A light will typically appear or flash to indicate it is on. Once it is on, it’s ready for use. If your vape pen is button activated, simply hold down the button as you draw from the mouthpiece of your cartridge. You’ll want to make sure you vaporizer battery is charged ...
How to use a vape pen?
If you are brand new to using a vape pen, it’s easy! Simply press the button on your battery, and inhale while drawing vapor from the mouthpiece. With an inhale activation battery, you won’t even need to press a button. Over time, you will learn what works best for you.
How long does it take for a vape battery to change colors?
It usually takes 2-3 rapid clicks of the button on your battery for the light to change colors. Each vape is different, so check your user guide to learn your specific voltage settings. If you ever have a question on your battery, you can always reach out to the friendly team over at VPM for support.
What is the bottom airflow cartridge?
Bottom-airflow cartridges have an air hole in the middle of the pin on the bottom of your cartridge. This allows the battery to activate when you inhale. Bottom-airflow cartridges will work with inhale and button activated batteries.
Do you need a top airflow cartridge for vaping?
If the answer is yes, you have a top airflow cartridge. These are a little less common, but they will only work on button activated batteries. 3. Charging your Battery. Charging your battery is crucial to your vaping experience. Most vapes will either use a Micro USB charger, or come with a vape pen charger.
Do vape batteries need to be charged?
Many vape batteries come somewhat charged, but we recommend charging before use to get the most out of your vaping sessions. Once your vape pen is on, there are two different ways you could activate the batteries: Inhale activation & Button Activation.
Do vapes need a charger?
Most vapes will either use a Micro USB charger, or come with a vape pen charger. VPM carries Vape Pen Chargers if you ever misplace yours, or if you just like to have extras around. Batteries will generally light up once they are plugged in indicate they are charging.
How to clean a pod from a vape?
Also check inside your vape where the pod attaches to it. If you see any ejuice or dirt, clean it out with a paper towel then reinsert the pod and try again.
What to do if cleaning contact points doesn't fix check atomizer error?
If cleaning the contact points doesn’t fix the check atomizer error on your pod vape, you’ll want to carefully examine the contact pins/plates on your pod vape and on your pod for damage.
What to do if your pod vape isn't firing?
If your pod vape isn’t firing, has a blinking LED and won’t fire, or says Check Atomizer or No Atomizer, you can follow a few of the same steps listed above for tanks: 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points.
What causes a check atomizer short?
Loose pieces of metal on the build deck will cause your mod to display “Check Atomizer” or “Atomizer Short”. Even very small pieces or trimmings of wire can cause a short or a check atomizer error on an RDA/RTA/RDTA. First, inspect the build deck closely for loose pieces of wire or other foreign objects.
Why is my mod reading the new tank correctly?
If your mod is reading the new tank correctly, it could be a problem with the coil on your other tank. You might also want to clean the contact points on the tank that was giving you the error. If your mod is still reading “check atomizer” with a new tank, it’s probably a problem with your mod.
What is a versed vaper?
The Versed Vaper team are a group of passionate and experienced vapers who take pride in writing helpful, quality content about vaping. From deals, to news and reviews, we've got you covered on all things vaping. Remember to subscribe to our newsletter, and follow us on Twitter, Instagram, and Facebook!
How to remove a tank from a mod?
Start by removing the tank from the mod and inspect the threading where the tank screws in for dirt , dust, or ejuice. Do the same with the 510 connector on your mod. Clean out the contacts with a paper towel, and screw your tank back onto your mod.
