First, fire it a couple times for a split second. Then, lock the resistance and it will lock the resistance you saw when you reattached the tank and not lock the old resistance of what it was before you detached the tank (basically, it'll lock the new detected resistance). Sometimes, that will even prompt the "new coil up same down" message.
Full Answer
How to Prim a brand new vape coil?
Unpack your brand-new coil from the box. Make sure that it is compatible with the manufacturer that you use for your vape. Use a dropper to drips and E-liquid along the wicking holes. In most cases around for drops will do to start priming a brand-new vape coil.
How do vape coils work?
The E-liquid from the device is fed along the coil and absorbed by the material which causes the evaporation and the vapor that you can inhale in a vape kit . If playback doesn't begin shortly, try restarting your device. Videos you watch may be added to the TV's watch history and influence TV recommendations.
Should I replace my vape coils if they're burnt?
If you've installed a new coil and primed it properly but you're still noticing a burnt sensation, replace the coil immediately. On occasion, defects will crop up in certain coils. Given the popularity of vaping and the number of manufacturers available, different manufacturers are going to have a unique quality control standards.
Why do my vape coils taste burnt?
When a new coil tastes burnt it emits a harsh burnt sensation to your throat and lungs. One reason this happens is if the coil is not primed properly and it is dry. When the vape device is fired and used at a high wattage it will heat up dry cotton and gives the vaper a burnt or dry hit.
m1ke Senior Member ECF Veteran
Does anyone know of a way to force the "new coil up same down" on a Pico?
TheotherSteveS Vaping Master Verified Member ECF Veteran
take off the atty, press the fire button until it shows no atomizer then remount the atty. This should work if the resistance is significantly different to its previous reading.
m1ke Senior Member ECF Veteran
take off the atty, press the fire button until it shows no atomizer then remount the atty. This should work if the resistance is significantly different to its previous reading.
TheotherSteveS Vaping Master Verified Member ECF Veteran
OK, I figured that. The resistance is just very close. In fact, it's the same coil (SS). I just was wondering if that message was forcible.
m1ke Senior Member ECF Veteran
you could put a different atty on, fire, then try again with the original! Its like the DNA40 as far as this is concerned...bit of a pain to be honest..
What is a vape coil?
What is a Vape Pen Coil? Vape pen coils are also called atomizer coils. These are heating elements that screw directly onto the battery inside a vape pen. This heating element on board also contains a wick or filament which is commonly made out of cotton or bamboo.
How to prim a vape coil?
Use a dropper to drips and E-liquid along the wicking holes. In most cases around for drops will do to start priming a brand-new vape coil.
Why does my atomizer burn?
This is because the wick has not had an appropriate amount of time to soak up the e juice for that hit. Instead of producing vapor, it's just producing the smoke from the coil as it dries the wick.
Why does my vape burn?
The Most Common Causes of Burnt Vape with the Wick. Vaping on high wattages: If you adjust your device to vape at an extremely high temperature, it's going to heat through the E-liquid far too fast. When the E-liquid is completely vaporized, the coils on board will start to burn the wicks. It's very important you check in on manufacturer wattage ...
Why does my vape taste burnt?
A bit of a burnt taste vape can just be an indication of a wattage issue and sometimes it can go away after a few puffs.
What is a dry hit?
A burnt hit and dry hit are somewhat similar. Dry hits occur when the wick that is inside the atomizer is allowed to dry up. When this on board wick is not exposed to any of the e juice, it can actually start to burn. The wick of the coil will start to dry up and even smoke with the heat that is being added to it.
How to get the best wattage for a vaporizer?
Eventually you will learn your device so that you can know how to work up to this sweet spot accordingly. If you can adjust the wattage, try raising the power once every few puffs until you reach the mid range of the device. Don't try raising the power to the limit of the coil as this can often cause dry hits easily.
How to prime a vape coil?
How to prime a new coil for tanks: 1 Grab the fresh coil out of the box 2 Drip a couple of drops of e-liquid on the wicking holes and inside the coil head 3 Reassemble the vape tank and fill it with your choice of vape juice 4 Screw the tank on your vaping device and set it aside for at least 10 minutes 5 After the 10 minutes, inhale on the drip tip of the tank without firing 6 Adjust the wattage on your vape mod to the lowest recommended wattage resistance then hold on the fire button slowly and inhale 7 Gradually increase your wattage setting until you find your optimal range
Why is it important to take time to prep and prime your new vape coil?
It's important to take time to prep and prime your new vape coil to make sure that you are getting the most out of it and not burning it straight out of the box. Learn more about the reasons why your coils burn out to ensure you never lose a coil again!
How to increase wattage of vape mod?
Adjust the wattage on your vape mod to the lowest recommended wattage resistance then hold on the fire button slowly and inhale. Gradually increase your wattage setting until you find your optimal range. Once coil life is done then throw the old coil away and repeat this process again!
Why does my vape get burnt?
One reason this happens is if the coil is not primed properly and it is dry . When the vape device is fired and used at a high wattage it will heat up dry cotton and gives the vaper a burnt or dry hit.
How long to inhale e-liquid?
Screw the tank on your vaping device and set it aside for at least 10 minutes. After the 10 minutes, inhale on the drip tip of the tank without firing.
What is a pod device?
Pod devices use refillable pods that utilize a pre-installed coil. Refillable pods are extremely easy to prime, just follow these simple steps:
Can you adjust wattage on a vape?
Pod systems do not have options to adjust the wattage, so just vape shorter puffs to break in the coil. If you take a long hit with a new coil it could burn it. So remember to start with shorter puffs!
