My Aspire Tank Is Spitting Hot E-Liquid Into My Mouth! If your Aspire tank is gurgling and spitting, the most likely reason is that your device’s wattage setting is too low. As a result, the air pressure from your puffs is drawing more e-liquid toward the coil than the coil can vaporize.
Why is my vape blowing dry puffs?
When the energy being produced by your vaping device doesn’t have enough vape juice to heat and evaporate, the temperature rises much faster. You’re likely to experience dry puffs since the wick could also burn. If gunking is the problem, you could solve it by getting a new coil.
Why does my vape get hot?
A vape is an electronic device that produces vapor which is inhaled by the vaper. It provides a great solution for people with nicotine and tobacco addiction. The vapor is produced when the battery supplies energy to the coil. In the process, some of that energy becomes heat. Since it’s electronic, it’s normal for your vape to get hot.
Why is my aspire vape not producing vapour?
Taking a draw with a fully charged and seemingly working device only to produce no vapour is an annoying one of the Aspire vape problems, to say the least. This could be down to a couple of problems. Make sure you check that everything is connected tightly.
Why does my vape coil get tired?
Sweeteners are notorious for clogging coils and reducing their lifespan, and the thickness of VG only makes things worse. Vaping on the higher end of the recommended wattage will strain your coils and reduce their lifespan. In effect, your coil is “getting tired” and starts flirting with burnt hits.
Why is my Aspire vape getting hot?
The most common cause of a hot vape: Chain vaping/hot coils It all comes down to the fact that part of your mod or vaping device is literally designed to get hot. Electricity going to your coil and heating it up is what turns your e-liquid into vapour.
Is it normal for my vape to heat up?
It is normal for the atomizer to feel warm or hot to the touch. If however it is so hot that you are unable to touch it, you should start by checking the coil. An accumulation of gunk on the heating coil will produce a lot of heat and very little vapor.
How do I stop my vape from getting hot?
Install an Insulator Between the Tank and the Mod The most common insulator for vaping is polyether ether ketone (PEEK). If you can find one, a PEEK spacer that fits between your tank and your vaping device can keep the heat from radiating to the device and battery.
Why is my vape tip so hot?
Vaping in the sun or when it is super-hot out will cause your vape pen to heat up considerably faster than if you were out vaping in the snow. If you know your pen has a hard time staying cool, just vaping in the shade an air conditioned room can help keep your mouthpiece at a more comfortable temperature.
Why does my vape feel like it's burning my throat?
Dry Hit. If you inhale when there is no vaping juice to vaporize, you will experience a "dry hit." This can cause a burning sensation that is very uncomfortable. This will temporarily cause a sore throat.
Can my vape explode?
Although these incidents appear uncommon, vape fires and explosions are dangerous to the person using the vaping product and others around them. There may be added dangers, for example, if a vape battery catches fire or explodes near flammable gasses or liquids, such as oxygen, propane, or gasoline.
Does vaping make you lose weight?
The short answer: vaping does not help you lose weight as a diet trick, despite that being the reason why some pick up an e-cigarette. Its sole purpose is to help people quit smoking by using a healthier alternative that follows a familiar pattern of holding something in the hand to inhale.
Why did my cart get really hot?
Carts get hot because electricity travels through the coil, turning your oil into vapor. The coil can reach temperatures of 300 °C / 570 °F or higher. While the outside of the tank won't get this hot, the heat is fairly concentrated and can make your device feel warm.
6. Adjust your airflow
Many of us love sumptuous clouds of vapour, but not when they’re raining fire upon our mouths!
Conclusion
Though it may seem like there are a lot of potential causes for a hot vape, in the majority of cases it’s a mixture between over-vaping and using too much power. It’s still best to nip this little issue in the bud however, and solve it as soon as you can.
Why is my coil hot?
High wattage gets the coil to be very hot, which in turn produces hot vapour. When you open the airflow, cool air from outside mixes with the vapour to cool it. If the airflow is restricted, the vapour will be too hot. Solution. Adjust the airflow to let in more cool air to cool the vapour.
Why is my vape so hot?
When you vape, the coils get hot. Usually, the temperatures get up to 3000 C or even higher. Manufacturers design these parts with insulation so you might not feel the heat at such high levels through the casing. But if you are having a problem with a hot vape, the coil is probably the main cause – especially is you are into chain vaping.
What happens if your wattage is too high?
High wattage/type of coil. If your wattage is too high, or you are using a complex coil tiger coil or a Clapton coil, you might have heat problems. These accessories are to be managed carefully. Though they have thermodynamics to cool them down, you can also try reducing the wattage.
Does a vape feel hot?
Eventually, the heat is bound to make it to the exterior. The heat will be concentrated at the base, and the body of the vape will feel warm as well. Also, the type of coil you are using can contribute to the problem. For instance, Clapton coils tend to burn hotter than standard coils.
Do Clapton coils burn hotter than standard coils?
For instance, Clapton coils tend to burn hotter than standard coils. The more complex a coil is, the more heat it will generate. And though this might be perfect for heavy smokers looking to blow large volumes of vapour, you need to be careful with their heat potentials. Solution.
Can you clean a coil?
But if you don’t want to, you can try cleaning the coil. Remove the gunk surrounding the coil, and you will be good. Of course, this will not be as successful as a new coil since there is only so much cleaning a coil can achieve. Also, it takes a while before the coil dries and you can use it again.
Is VG more viscous than PG?
Generally, VG is more viscous than PG. Therefore, e-liquids with a higher percentage of VG (usually more than 70%), have problems wicking. On the other hand, some tanks have flow control. With this tech, the path between the wick and tank is closed or constricted, leading to insufficient juice flow. Solution.
Why is it important to eliminate hot spots before using a coil?
It’s important to eliminate hot spots before using a coil because a coil that heats unevenly will never give you a good vaping experience. It’ll always create hot, harsh vapor that doesn’ t taste right — and since it’ll quickly burn through the wick, things will only get worse from there.
What is temperature control in vaping?
Temperature control is a vaping technology whose time seems to have come and gone. While you could once expect to find at least one titanium or nickel coil available for any given tank, today it isn’t even a given that you’ll find a stainless steel coil for your tank since kanthal mesh is all the rage.
Why do coils have hot spots?
A hot spot is a section of a coil that glows much more brightly than the rest of the coil due to uneven spacing between the wraps of the coils.
What is the form factor of a sub ohm tank?
One thing worth noting is that many of the replacement drip tips that you’ll find today use the wide 810 form factor. Many older sub-ohm tanks use the narrow 510 form factor. If your tank’s mouthpiece is around the same size as a cigarette filter, it’s a 510 mouthpiece.
Which drip tip material is best for vaping?
Between the three popular drip tip materials, Ultem has the highest heat resistance and may be the best choice for extremely high-temperature vaping. For non-extreme sub-ohm vaping scenarios, though, any of the three materials work well.
Do vape tanks have drip tips?
If you own a vape tank made more than a year or two ago, though, your tank may have a stainless steel drip tip. A while back, tanks like the Aspire Triton and the Horizon Arctic helped to make that design all the rage.
Can a vape tank get hot?
If your tank has a metal mouthpiece that gets hot when you vape, you’ll want to swap it out for a plastic mouthpiece that doesn’t conduct heat to your lips.
What is the best way to keep your vape tank cool?
Many modern vape tanks use Delrin or Ultem mouthpieces. Both of those materials are forms of plastic that conduct heat poorly and can help to keep your lips cool. If your vape tank is getting hot, then, one very simple solution is to replace the mouthpiece; the heat from the coil will stop reaching your lips.
Why is my vape tank hot?
The first reason is that the tank has a metal mouthpiece that directly touches the tank’s chimney or coil. Since metal conducts heat, the heat from the coil will travel to your lips if that’s the case. Modern vape tanks get around that problem in two ways.
What is the best insulator for vaping?
The most common insulator for vaping is polyether ether ketone (PEEK). If you can find one, a PEEK spacer that fits between your tank and your vaping device can keep the heat from radiating to the device and battery.
Why do tanks use metal mesh?
Instead, today’s tanks use strips of metal mesh that provide the same heating area with much lower metal mass.
Is vaping hot or cold?
One final thing to remember about vaping is that, to a certain extent, heat is always going to be part of the equation when you’re using a sub-ohm tank. Anything that’s designed to produce large vapor clouds is going to get warm during operation, and the vapor that it produces will be warm as well. If that isn’t what you want from your vaping experience, you might be happier if you switch to a refillable pod system with nicotine salt e-liquid.
Do you need an insulator between a vape tank and a mod?
Install an Insulator Between the Tank and the Mod. Aftermarket insulators or spacers for vape tanks aren’t as common today as they used to be because, as mentioned above, excess residual heat just isn’t as common a problem with vape tanks as it once was. Today, vape tanks that require heat insulation have the required insulators built in.
Can a hot vape tank make you uncomfortable?
A hot vape tank can really put a damper on your vaping routine. If a tank gets hot enough, the mouthpiece can become quite uncomfortable against your lips. In some cases, you may feel the heat from your tank radiating into the body of your vaping device – and that might cause you to worry.
How to clean coils on Aspire tank?
You can also clean the atomizer coils for your Aspire tank by swishing them in warm water or vodka. Cleaning a coil removes some of the crust and can prolong the coil’s life. It will not, however, fully restore the coil’s original flavor. After cleaning an atomizer coil, allow it to dry for about 24 hours.
How to get a good mouth to lung vape experience?
By replacing the mouthpiece and adjusting the airflow collar, you can get a good mouth-to-lung vaping experience with almost any tank. Don’t forget that reducing the tank’s airflow will cause the coil to run hotter. You may need to lower your device’s wattage setting to compensate.
What to do if your Aspire tank leaks?
The first thing that you should do is disassemble and reassemble your tank.
What is the wattage of an Aspire coil?
Wattage Range. On the side of most Aspire atomizer coils, you’ll see a set of numbers – such as "40-60W” – indicating the coil’s suggested wattage range. Although the range is only a suggestion, you’ll generally have the best experience if you set your device’s power within that range.
Why does my Aspire tank gurgle?
If your Aspire tank is gurgling and spitting, the most likely reason is that your device’s wattage setting is too low. As a result, the air pressure from your puffs is drawing more e-liquid toward the coil than the coil can vaporize. The excess e-liquid pools and spits out through the mouthpiece.
How to replace coil on Aspire atomizer?
In most Aspire tanks, the atomizer coil is connected to the tank’s bottom hardware. To replace the coil, twist the bottom hardware to remove it from the tank. Twist the atomizer coil out of the base and twist in a new coil. Prime the coil with a bit of e-liquid before using it for the first time.
How to replace glass in Aspire Triton?
To replace the glass, disassemble your tank and remove any glass fragments with tweezers. Push gently to get the replacement glass sleeve into position and reassemble the tank. Note that in the Aspire Triton, the glass is a permanent part of the upper hardware.
Why does my Aspire Breeze gurgle?
Why is my Aspire Breeze vape gurgling? The gurgling of your device will be because there is e-liquid trapped where it shouldn’t be. This is usually in the coil or air tube (chimney) which leads from the coil to the mouthpiece. It will kind of sound like you are sucking a straw.
What is Aspire Vape Kit?
Aspire Vape Kits are known for building quality and great safety features. Which is why they’re one of our best sellers. However, like with everything, sometimes problems crop up.
What happens if your vape coil is running low?
You also want to make sure you have a tank full of e-liquid. If it is running low then there will be nothing to pull into the coil to produce vapour.
Can you see if your atomizer is on your vape?
No atomiser found will be on the LED screen on your device if your vape isn’t reading the coil. You might need to tighten up the connection between the mod and the device and check that the coil is connected inside the tank.
BrotherBob ECF Guru ECF Veteran
Just wanted to record this in case someone else comes looking for a fix to this issue.
vaper1960 Moved On ECF Veteran
PockeX was my first vape device (gave it to a friend that is trying to cut down on smokes) It served me well. Which coils are you using (0.6 or 1.2 ohm)? Make sure when you change coils to fill tank and wait at least 10 minutes before vaping.
nbfdmd New Member
Man, I wish I had found this post. When I had the exact same problem, I googled it and only a similar post from 2017 showed up, with no solutions offered.
How long does a coil last?
Consumption. A coil is generally good for up to a certain amount of e-juice. The more you use it, the faster it dies. Coil life is sometimes calculated in days or weeks, but the most accurate way to calculate it is in mL—some people vape only a couple of mL per day, while others will consume 10-20 mL or more.
How to know when your coil is done?
Knowing when your coil is done is not a science, but it is a learning process. The more you use a vape tank, the more aware you become of the time you need to grab a new coil out of the box. The first sign will usually be a loss of flavor, followed by a drop in vapor production.
How to start vaping on a pod?
When you first begin vaping on a pod, try and take shorter puffs to begin with. Some of the smaller coils need to be broken in a bit before being pushed. If you take really long hits to start, even if the wick is fully saturated, you could get a burnt hit.
How to prime a vape tank?
How to prime vape tank coils. All vape tanks that come with replaceable coil heads have more or less the same structure and require the same simple steps to get primed. You will need to repeat this process every time you replace a coil. Take a new coil out of the box.
Why does my e-liquid burn?
Here are some of the most common reasons behind burnt hits and some advice to help you avoid them. High wattages. Vaping at wattages that exceed the coil limits will vaporize e-liquid too fast. When that happens, the coils can burn the wicks, even when there’s still some juice there.
How to keep vape wick from drying up?
Always stay inside the recommended wattage ranges. Chain vaping. When taking many puffs in a row, the wick will dry up fast. If you sense that a burnt hit is coming, by noticing a slightly roasted taste, put your vape down for a moment. This will allow liquid to cover the dry spots of the wick.
What to do if your coil is burnt?
Don’t be discouraged. Vaping is an enjoyable safer alternative to smoking. If your current coil tastes burnt, grab a new one and discard the bad one. Just don’t forget to prime it first!
Why do multi strand coils pop?
Multi-strand coils often pop and spit due to their design. Twisted coils in particular have a bad reputation for this, but Clapton coils may have the same issue. Their design makes it easier for e-liquid to pool on the coil, and so sometimes it’s hard to entirely avoid popping on these coil types.
What happens if you inhale too much liquid?
If you inhale too forcefully, you risk bringing too much e-liquid into the coil, which may lead to leakage. Watch out when filling – Never overfill your tank. Always leave a small air pocket at the top when filling. This empty space will help prevent any liquid from leaking out.
Why does my vape tank leak?
Leaking happens when e-juice escapes from your tank, usually through the airflow system. Depending on the reason behind it, leaking can range from a few drops of e-liquid, to having your tank emptying all of its contents all over your vape mod. It’s a common problem with even the most popular sub ohm tanks.
How to remove e juice from a tank?
First make sure the threads are in sync and closed tightly, but not too tight. Find that sweet spot. If the threads are crossed, screw it back together carefully. Remove e-juice from chimney – All tanks have a central airflow tube that runs from the body of the tank up to the drip tip, known as the chimney.
Why does my tank leak out of the airflow holes?
Put a lid on it – If you leave a tank without the top cap, it will leak out of the airflow holes. That’s due to the pressurized nature of tanks. Make sure that your tank is empty if you plan on leaving your top cap off for extended periods of time—anything longer than it takes to fill it.
What does it mean when a juice tank is not airtight?
Check for cracks – Check your tank for cracks or other damage. A thin crack in the glass or a piece of bent metal can mean the tank is no longer airtight, allowing the juice to leak out and into the air hole valve.
How to prevent juice from leaking?
Sometimes if you’re in a hurry, you may cross-thread the top cap or forget to screw it together tight enough. This can cause juice to leak out of the openings.