Kanthal and Nichrome (60 or 80) are best used in standard wattage mode. Sent from my iPod touch using Tapatalk Thanks for the quick response, just wanted make sure I wasn't going to get sick from vaping on N80 outside of TC mode.
Full Answer
What do you like most about N80?
N80 is a little different but not worse. I like that I can dry burn it without it turning purple. I like N80 fused claptons, aliens, and fraliens. It ohms lower than kanthal and heats up faster. This is good for using on mechs. I have mech squonks that perform fantastic with N80 builds.
Can I use nichrome N80 for wattage mode?
Hi, new here. I picked up some Nichrome N80 and was wondering if I can use it for wattage mode and not temp control. Nichrome 80 (nickel chromium) has been used for voltage and wattage control for many years, that's what it's for. It's temperature coefficient of resistance is too low to be used alone for temperature control from what I've read.
What is the difference between N80 and N80 wire?
N80 will be faster and have more surface area per ohm. N80 will be easier to damage rewicking and such.. but IMO better flavor potential. Clouds meh type of wire doesn't really apply here.
What's the difference between N80 and 34G?
Plus it's harder to alien 34g. N80 will be faster and have more surface area per ohm. N80 will be easier to damage rewicking and such.. but IMO better flavor potential.
Can Nichrome be used in wattage mode?
Another type of wire well suited for wattage vaping is Nichrome. Nichrome wire is an alloy composed of nickel and chromium, and may also contain other metals such as iron.
Is N80 a Nichrome?
Nichrome (N80) Wire.
Can you TC Ni80?
Kanthal and Ni80 Don't Work On TC Mode This makes it very hard for your TC vape chip, because it can't 'see' the coil temperature just by looking at your coil's resistance.
What is TC mode vape?
Temperature control (TC) in vape mods is a technological solution for dry and burnt hits. It also creates a consistent vape while taking longer drags because the temp stays the same—instead of getting hotter. The user chooses the temperature limit, typically from a range of 300°F to 600°F (100°C to 315°C).
Is N80 a nickel?
650/N80 is an austenitic nickel-chromium alloy (NiCr alloy). The alloy is characterized by high resistivity, good oxidation resistance and very good form stability. It has good ductility after use and excellent weldability.
Which is better nichrome or kanthal?
Kanthal has a slightly higher maximum operating temperature as well as a higher melting temperature than Nichrome, giving it a slightly longer lifespan than Nichrome. Some people claim that Kanthal wire puts off a slightly metallic taste due to the Iron composition, whereas others claim it does not.
What setting should my vape be on?
As a general rule, dab temperatures are set between 315℉ to 900℉. Below 315℉ is usually too low to vaporize cannabis concentrates. And above 900℉ can release carcinogens as well as a harsh, burnt vapor.
What is TC TCR mode?
The Temperature Coefficient of Resistance (TCR) A temperature coefficient expresses the gradual change in the physical properties of the wire as the temperature changes (a property required for TC vaping as discussed earlier).
What should my Smok vape be set at?
For 2-ohm coils, the ideal voltage falls between the ballpark of 3.3 to 4.0 volts. Higher ohm (aka higher resistance) coils allow for a higher voltage.
What is NI TI and SS?
Stainless steel (SS), nickel (NI), and TI (titanium) are all wire materials. With the exception of stainless steel, which can be used in wattage mode and SS mode, they should only be used in those mods that correspond to them. They allow you to limit the temperature you vape at.
What is VV mode vape?
Variable Voltage Mode, or VV mode, is a setting on your vape device that lets you define the precise voltage (Volts) running through your device. VV devices don't require a very advanced vape chip, so they tend to be slightly cheaper than VW devices.
What is SP mode Vaporesso?
Super Player mode (available with the Swag II) is another Vaporesso speciality, which essentially allows you to use coils with a wider range of resistances than the device usually supports, down to 0.03Ω (and up to 5Ω) for the Omni Board 4.0 (and up to the more recent V 4.2).
What is the wattage of a box mod?
The wattage of a box mod, in layman’s terms, is essentially the amount of power you send from the mod’s battery to the atomizer (AKA your vape tank). Higher wattages equal more power, and this, in turn, creates a hotter, more intense hit. And more vapor. If you want those BIG clouds, you gotta run your vape mod at higher wattages.
Can you control the temperature of a box mod?
But Temperature Control vaping is a very useful feature of a box mod, as it allows you to control the maximum temperature that the atomizer will fire at. You can set it wherever you like, for instance, if you’re vaping sweeter E Juice, you could set it nice and low, to really juice-out the flavors.
Do vape mods have a user interface?
Most modern vape mods run on a vape chip and software, just like a smartphone. Vape mods also have a user interface, buttons, and a display . In fact, they’re probably closer to a mobile phone than a cigarette in this respect. Please though, DO NOT be put off by ALL the settings and bells and whistles inside your box mod.
Why use N80 for mechs?
If you're using mechs get n80 because A1 won't heat fast enough. 24g isn't worth buying for exotic stuff. If you can get 36g fuse, your builds will be that much better. 34g and bigger takes a tole on your ramp speed and the temp of your vape. Plus it's harder to alien 34g. Sent from my E5306 using Tapatalk.
Why is A1 faster than N80?
If you're using a regulated mod get A1 because the parallel runs will put you under 0.1 really fast with n80. If you're using mechs get n80 because A1 won't heat fast enough.
What wires are used for power mode?
Most vapers prefer power mode: it is just simpler. Kanthal, stainless steel, and nichrome are the three most popular power mode wires right now, and you might be wondering what would be the best one for you. Again, take note that if you have (or suspect you may have) a nickel allergy, then you should not vape on nichrome coils, ...
Is titanium wire safe for vaping?
The last wire we will look at is titanium, which is another TC-only wire. There is some controversy surrounding the safety of titanium wire when used for vaping. Heating it can release a toxic component (titanium dioxide) above 1200 ℉ (648 ℃).
Can you vape with nichrome coils?
Again, take note that if you have (or suspect you may have) a nickel allergy, then you should not vape on nichrome coils, and maybe you should also avoid stainless steel. Kanthal has been the choice of most vapers for a longer time, due to its ease of use and higher resistance.
Can stainless steel be used for vaping?
Nichrome and stainless steel on the other hand are excellent power mode wires for vaping at lower resistances—that’s not to say that they can’t be used for all kinds of inhales.
What is temperature control vaping?
Temperature control vaping can be an amazing experience. It provides the security of consistency that wattage vaping often lacks. No one likes dry or burnt hits, or vapes that get too hot with long hits. TC vaping solves that.
What is the best wire for vaping?
TC vaping generally uses one of these four types of vape wires: 1 Stainless steel: this wire is very popular and readily available. It comes in various grades such as 304, 316, 316L, 317, and 430 but the most common is SS316L. SS can be used in wattage or temperature control mode. 2 Nickel 200: commonly known as ni200, it was the first temperature control coil but it’s less common now due to some vapers having sensitivities to nickel. 3 Titanium Grade 1: otherwise known as Ti. It works well in TC but the user has to make sure it does not get overheated. 4 Nickel ferrous: also known as NiFe, comes in various grades such as 48, 30, 52, 70 and can be used in either mode, but is not widely available.
Why is my vape consistent?
Vape consistency: By having control over the temperature your coils can rise to, the vape will be consistent from puff to puff, and even within one puff. In regular wattage mode, the hits are more inconsistent because the heat of the coil changes based on the length of the hit.
What type of wire do you use for vaping?
Next, you must vape with the right wire type. TC vaping generally uses one of these four types of vape wires: Stainless steel: this wire is very popular and readily available. It comes in various grades such as 304, 316, 316L, 317, and 430 but the most common is SS316L. SS can be used in wattage or temperature control mode.
What is the advantage of TC mode?
In TC mode, if the wick runs dry the temperature will start to rise, and therefore the temperature protection will immediately cut power to compensate.
Can you adjust wattage on a vape mod?
Prior to TC, most top vape mods could only adjust watts (another innovation from Evolv a few years prior.) Now in 2020, like wattage control, temperature control is a feature found in most vape mods.
Can you take long hits with a TC vape?
Hopefully, you’ll get a good vape and, because it’s TC, you should be able to take really long hits without fear of overheating the coil and wick. It should be just like normal—except when you run out of juice you’ll notice the vapor dropping off significantly. Adjust the temperature up or down if necessary.
Element vapes new delivery service
Does anyone else order with element vape and the package is in your hometown but the keep rescheduling delivery and not even attempting at all?? It’s ridiculous (Update) I got it but it was like a week late and they delivered to the wrong house
Just bought a Vaporesso Gen S and I need help!
So I just purchased my first mod (Gen S) and since this is literally my first E cigarette, I was stupid enough to buy a disgusting E juice (strawberries flavor but it’s just overall disgusting). Not only that but I bought a 120ml package of it 🤦♂️ Anyways, I’ve found a couple of other flavors I like and I’m wondering how I should go about.
