Full Answer
How do I set my TCR on my vape?
How to vape in TC. Put your mod into TC mode and select the corresponding wire type for the coils you have. If the mod has a TCR you can enter the exact TCR value. After that, ensure that your mod and tank are both at room temperature so the temperature readings will be more accurate.
What wattage should I vape at RTA?
Often, regardless of the type of tank, the best performance of the majority of vapes occurs between 80 and 100 watts. Higher wattages will render your coil “useless” – burn out and reduce the battery life.
What temp and wattage should I vape at?
Many people agree that 420 degrees Fahrenheit or 216 degrees Celsius is the sweet spot. You get as much flavor as possible without feeling the warmth of the vapor. If you want to add even more flavor, try a temperature between 425 and 450 degrees Fahrenheit or 218 and 232 degrees Celsius.
What setting should I set my vape to?
As a general rule, dab temperatures are set between 315℉ to 900℉. Below 315℉ is usually too low to vaporize cannabis concentrates. And above 900℉ can release carcinogens as well as a harsh, burnt vapor.
What ohm is the best for RTA?
The standard or regular level of ohm when it comes to vaping and your clearomizer is between 2.4 and 2.8. This is by far the most common ohm range chosen by those looking for replacement coils, with the most commonly chosen being 2.5.
What wattage should I vape at 1.4 ohm?
The other coil that comes with the kit is the Nord regular coil, which is a 1.4-ohm coil head with a maximum wattage of 12 watts.
Does higher wattage burn coils faster?
When you vape at a high wattage, the liquid absorbed by the coil's wick could be burning off faster than the wick material can absorb more ejuice.
What wattage should I vape at 0.6 ohm?
12-25 wattsIn contrast, the 0.6ohm coils have a recommended wattage of 12-25 watts. They are therefore classed as restricted direct to lung (RDL) coils, offering less clouds but conserving your battery and e juice.
What wattage gives the best flavor?
The sweet spot for getting a balance of vapour and flavour is around 0.3ohms. Depending on your coil choice you'll want to up the wattage from anywhere between 50 and 100 watts. Clapton and Alien coils usually take a bit more power to ramp up so you'll want to boost the wattage if you're using either of these options.
What temp should my cart be at?
Vaping CBD isn't much different than vaping THC oil, as higher temperatures tend to produce the most effects. To maximize your experience when vaping CBD, a temperature of 410°F should do the trick.
What wattage should I vape at 0.2 ohm?
0.3 ohms - 40 watts to 90 watts. 0.2 ohm coils - 40 watts to 100 watts.
How do I get more clouds from my vape?
Small changes to the way you inhale and exhale while using a vaping device can affect the clouds produced. Try leaning forward slightly and straightening back up as you inhale. Straightening up while inhaling naturally opens up the lungs and allows more vapour to enter them.
What does the column "Total R by temperature" show?
The column "Total R by temperature" will now show you the total resistance of your coil at various temperatures.
How much resistance is in a Ni200 wire?
Update the table with the resistance of each piece of wire. E.g. 0.15 for the Ni200 and 1.5 for the Kanthal. (There will be a way for you to directly insert the wire gauge with time, but for now you'll have to rely on the coil calculator to figure the resistance out.)
What does the calculator use to calculate resistance?
If no table is present for a material , the calculator uses the TCR to calculate the resistances.
What is normalized TFR curve?
The row "normalized TFR curve" is normalized so that the factor at 70 °F is always 1. These values are used in the DNA 200 output.
What does the resistance table show?
The table shows you the calculated resistance for each wire, at different temperatures. You'll notice that as you change the resistance of each wire, the calculated resistance values are updated.
Does changing temperature points reset calculator?
Changing the temperature points will reset the calculator.
How many watts does a Merlin mini vape?
Just bare in mind the Merlin Mini can't handle high wattage. Even with the dual coil configuration I found I got dry hits above 70 watts. With the single coil I only vaped it at 30 watts
What is temp control?
Then you should know that Temp control has its name, means control of coil is done based of temperature. So clapton coils although are very delicious, but become hot so fast and your mod will switch to PROTECTED. My suggestion. Use simple SS wire, and if you prefer go to spaced coils.
How many ohms does SS316L have?
For temperature control using SS316L 28 AWG single wire, I use 6 1/2 SPACED wraps, 2.5 I.D., resistance comes out to around 0.68 oh ms, vape at 12.to 12.5W. I vape MTL, prefer a cooler vape, and this serves me well.
How many ohms should coils stay in a coil?
In Temp control mode, your coils should stay 0.15-0.18 ohm. These are the best points as lower ones are not recommended.
How to get rid of hot spots on a coil?
Get some ceramic tweezers, lightly pulse your coil at around 25-35 watt, and then gently squeeze it. After that strum the coil a couple times to fully eliminate the hot spot (s).
Does temp control give you cold vapes?
I must add, temp control will give you cold vapes, so if you are fan of warm vapors, then this style will not satisfy you.
Under the Hood of the OBS Engine RTA
Compared to the other 25mm RTAs from other companies, the OBS Engine actually has a lower profile. The diameter at the base of the Engine is 25mm, and it is just 50.8mm tall from the top of the atomizer to the base. This is including the Delrin drip tip.
Taking the Engine RTA for a Spin
The OBS Engine RTA is probably one of the most user-friendly tank atomizers currently available. The Velocity-style posts on the build deck make coil installation simple and hassle free. This way, you don’t even have to bend the legs of the coils to center them on the deck.
Final Thoughts
The OBS Engine RTA has all the features and benefits that vapers are looking for in a tank atomizer. It’s almost the perfect RDA in my opinion. Firstly, it can hold a good amount of liquid. Second, it is easy to clean and maintain. Third, the build deck is simple, yet effective. Finally, it produces flavorful clouds.
