How to use the Pulsar
Pulsar
A pulsar (short for pulsating radio star) is a highly magnetized, rotating neutron star that emits a beam of electromagnetic radiation. This radiation can be observed only when the beam of emission is pointing toward Earth (much the way a lighthouse can be seen only when the light is poi…
How do you use a pulsar APX vaporizer?
Press the power button five times to turn on the vaporizer. To change between its 5 temperature settings, hold the button for 3 seconds to begin cycling through and release to choose your setting on the LED screen. To hit the pen, hold down the power button and inhale through the mouthpiece.
How do you turn on a pulsar vape?
0:052:17Pulsar APX Wax Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe Pulsar apx wax vaporizer does not have any type of temperature. Control simply press and holdMoreThe Pulsar apx wax vaporizer does not have any type of temperature. Control simply press and hold the power button until the light changes from red to green heating.
How do you use a pulsar flow vaporizer?
0:144:00Pulsar Flow Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe high setting will be indicated by an illumination of the light closest to the charging port onceMoreThe high setting will be indicated by an illumination of the light closest to the charging port once set the unit will begin to heat. So let the unit sit and run through a full cycle.
How does APX smoker work?
0:384:39APX Vape & APX Smoker Review - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the a px vape is really simple I went ahead and turn mine on right now and set 392 degreesMoreSo the a px vape is really simple I went ahead and turn mine on right now and set 392 degrees Fahrenheit. One two three four five clicks will turn it on and off.
How do you open APX vape?
0:352:02Pulsar APX V2 Vaporizer Tutorial & Unboxing - Tools420 - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe pulsar a px vaporizer is pretty easy to use turn the unit on press the on button five times andMoreThe pulsar a px vaporizer is pretty easy to use turn the unit on press the on button five times and repeat the same to turn the unit off to load the unit take the top mouthpiece off note.
What does 10 blinks mean on a vape pen?
Dying battery: Most often, the vape pen will blink ten times when the battery is too low for proper vaping. To fix the issue, recharge the battery. Low voltage: If the battery is charged but the pen is still blinking, it could be due to a low voltage.
How do I use VLeaF go?
How To use your VLeaF GOLoosely load the chamber full of herb. ... Press the power button 5 times to turn it on or off.Adjust the temperature by pressing the button twice ( green = low, yellow = medium, red = high )Press and hold the button to take an on demand draw.For session mode, press the button three times.
How do you charge a pulsar vape pen?
0:541:38How to Properly Charge Your 510 Thread Vape Battery - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe correct way to charge your battery is to use a laptop or a standard 5 volt black charger thatMoreThe correct way to charge your battery is to use a laptop or a standard 5 volt black charger that you plug into the wall.
What is APX vape?
The new and improved APX Vape V3 combines portability with a maximized herb chamber to create an unmatched vaping experience. With just a 30 second heat time, this dry herb vaporizer is efficient with a "Cash" feature that ensures the last of your product is spent or for taking quick hits with high heat.
How to clean 510 threading on a vape?
Use the swab to wipe the inside of the coil chamber until clean. Unthread and remove the coil from the vape body. Use the cleaning swab to wipe the 510 threading of the vape body. Re-assemble vaporizer and dry-fire before use.
How to clean a vape coil?
Make sure the vape unit is turned off and the heating coil element is cool. Use an alcohol-filled cotton swab or lightly dip a dry cotton swab in 91% isopropyl alcohol. Use the swab to wipe the inside of the coil chamber until clean. Unthread and remove the coil from the vape body.
How to clean a mouthpiece?
Place the mouthpiece in the container with isopropyl alcohol for one hour. Remove and wipe with a cleaning wipe. Rinse in cold water and dry with a hand towel or paper towel. Cleaning the coil chamber - These steps can be performed while the mouthpiece is soaking.
How to clean a vaporizer chamber?
The best way to clean the chamber is with an alcohol-filled cotton swab. These steps can be performed while the mouthpieces are soaking. Ensure vaporizer is turned off and fully cooled prior to cleaning. Snap the stem of the cotton swab to release the isopropyl alcohol into the cleaning tips. Alternatively dip a dry cotton swab into ...
How long to dry fire a vaporizer?
Swirl the cotton swab tip around all surfaces of the heating chamber and surrounding areas to remove resin and other residues. Let the vaporizer sit for 3 minutes and then dry-fire by turning it on to the highest heat setting. The heat will evaporate any remaining alcohol residue.
How long to soak silicone mouthpiece?
Separate the silicone liner from the plastic mouthpiece and place them in the soaking container for one hour.
