When there is not enough power coming from the vape pen battery, your vape will give a blinking light (a red light usually) to let you know you need to charge it. To see if this is the case, leave your battery charging until the light stays on (or the lights turn green), indicating a full battery.
Full Answer
Why is my vape pen not charging?
Problem #2: My Vape Pen Won’t Charge or Draw The most common reason for this is there isn’t proper contact between the battery and the cartridge, meaning your battery can’t fire the heating coil. This can be solved by adjusting the connection plate inside the thread to get better contact with the battery.
Why is my vape pen blinking?
The most common reason for a flashing light on your vape pen is to indicate that your battery is running low. When there is not enough power coming from the battery, your vape will give a blinking light (a red light with some devices) to let you know it needs to be charged. To see if this is the case, charge your vape until ...
How long does it take to charge my Openvape pen?
If you’re using an O.penVAPE 2.0 battery initiate rapid-charge mode for a 30-minute full charge! Is My Product Compatible? O.penVAPE pens are 510 thread size, and should work with most cartridges out there, but we do always recommend using our pens with our cartridges for the best results.
How do you turn on a vape battery?
If your vape has a pull-to-draw battery, the battery is always “on.” Pull-to-draw batteries remain “on” until they die, and you recharge it using its USB port. Other vape pens use batteries with push-button atomizer activation. To turn these pens on, you’ll need to push the battery button five times quickly and hold the button down when you pull.
Do vape pens light up when charging?
Simply connect the pen battery to the charger and insert into a USB port on a computer or other electronic device. The light on the battery and charger should illuminate, letting you know that it's charging up. Once the light on the charger turns green, the battery is fully charged and ready to use.
Why is the light on my vape not turning on?
Try a different cable/plug. If still nothing, then it is most likely an issue with the device itself. Either the charging port is faulty, the battery has died completely or the display/LED isn't working properly. Batteries do degrade over time in any device, as is their nature.
What do you do if your vape pen isn't charging?
Replace the battery Finally, if nothing works, your vape pen may not be charging due to a bad battery. It may have gotten wet, dropped, or simply worn out. Unfortunately, since the battery is usually the main part of your vape pen, replacing it may not be an option.
How do I know if my vape is broken?
There are some recognisable ways your e-cigarette shows you that it needs a new coil, as well as a few less obvious ones.Your Vape Tastes Burnt. ... Your E-Cigarette Is Gurgling. ... Your Vape Tastes 'Strange' ... Your Coil Is Used Up. ... E-Cigarette Leaks.
Why will my vape charging but not turn on?
There could be something blocking the connection between the battery and the clearomiser. Try cleaning the battery terminal and end of your clearomiser with a cotton bud. Another thing to check is that the tank or clearomiser is making contact with the battery terminal.
How do I get my vape to work again?
Break Air Bubbles. If you have a pod-based disposable vape, you might get weak hits if air bubbles form around the pod's wicks. Tap the device gently on a table to break the air bubbles. After giving the wicks a few seconds to get wet, you should get some nice hits again.
How do you test a vape battery?
0:006:37How to test your battery and coil - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou take your negative test lead and your positive test lead then put them to your negative andMoreYou take your negative test lead and your positive test lead then put them to your negative and positive terminals of your battery. You can see on the multimeter.
How do you unlock a vape pen?
Make Sure The Battery Is Unlocked To unlock or lock an OK Ego Vape Pen battery, simply press the button 5 times in quick succession. The blue LED on the battery's button will flash 3 times to indicate that it has been locked or unlocked.
How to prolong the life of a vape pen?
Let your vape pen rest between hits to allow the wick to re-saturate with oil. Getting into the habit of cleaning your coil, as well as priming new coils, is another way to extend the lifespan of your coil while avoiding burnt wicks.
How to avoid burning a vape?
To avoid burning your cannabis oil and damaging your coil, use a lower wattage and a lower temperature setting on your vape pen. Using a higher setting can result in the atomizer vaporizing the oil too fast, and burning the wick. Additionally, taking shorter pulls reduces the heat exposure. If you take large draws, you’re more likely to burn your oil.
How to turn on a vape pen?
Other vape pens use batteries with push-button atomizer activation. To turn these pens on, you’ll need to push the battery button five times quickly and hold the button down when you pull.
How to loosen up cannabis oil?
If you don’t have a hairdryer on hand, there are other ways to loosen up your cannabis oil. Heat a pot of water on a stovetop, until steam is produced. Then hold your vape pen over the steam for 20 seconds. This should result in the same effect as the hairdryer method, with your cannabis oil becoming less viscous.
Why is my vape pen not working?
There are several reasons why your vape pen may not be working properly. Some of these causes are easy fixes, such as oil setting and getting stuck in your cartridge. Others are more technical, like a battery, atomizer or coil issue. Most of the time, your vape pen isn’t actually broken. More often than not, once you identify the issue with your vape pen, you’ll be able to troubleshoot.
How to get rid of a settled cannabis cart?
A common solution for freeing up your settled cannabis oil involves using a hairdryer to heat the cart. Separate the cart from the battery and set the cart upright. On its low setting, hold a hairdryer about six inches away from the cart. Apply heat for about 30 seconds. When you see bubbles forming, let the cart sit for a few seconds. Then reconnect the cart and take a pull. If your airflow is still obstructed, repeat the process again.
Why is my atomizer not working?
Over-tightening: A common cause of atomizer problems is over-tightening. If you tighten the atomizer with too much force, it can sever the connection with the device . If the connection is intact but it still isn’t working, there may be an issue with the center pin (510 connector).
