The X MAX Starry is pretty simple to use, as you would expect when it comes to budget portable dry herb vaporizers. Just open the chamber and load up your herbs. From there, hold down the power button for three seconds and the device turns on.
Is the xvape Starry easy to use?
Xvape Starry 3.0 is very easy to use, vaporizers are trending towards being more complicated, but the Xvape Starry 3.0 reminds us a lot of the original but the better, Xvape straightforward and simple. There are three buttons, one to turn it on and two to adjust the temperature.
Is the xMax Starry a clean vaporizer?
A clean vaporizer means a happy vaporizer owner, and the XMAX Starry is no exception. When it’s clean, it’s easier to use, the vapor tastes better, and it’s more efficient.
How long does it take to charge the xvape Starry vaporizer?
Don’t worry though, once the first charge is complete, it will then only take around 90-120 minutes to reach full capacity - after which you can expect a 70-90 minute battery life in-between charges. To charge the Xvape Starry vaporizer, you must plug the USB charging cable into the device’s USB port and then into any power source.
How do I set the temperature on my xvape Starry?
Using the temperature buttons, set the vape to your preferred heat. The Xvape Starry has a temperature range from 212-464°F, but we wouldn’t recommend going above 430ºF unless you’re really looking to cook your herbs.
How do you use starry Max vape?
X-MAX Starry V2 Vaporizer – preparation First, charge the battery to the maximum, then switch the device on by pressing and holding the button and set the temperature at 240 degrees Celsius. Now let the vaporizer work until it switches off automatically, which will happen after 5 minutes.
How do I turn on my xmax vape?
Let's start by familiarizing ourselves with the controls on the XMAX V2 Pro. To turn it on, press the power button three times. This will put it in standby mode, indicated by the blinking lights. Hold the power button for two seconds to engage the heater, which will automatically head for the last used temperature.
How do you clean a starry 3.0 vape?
0:281:51XMax Starry Cleaning Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo clean the mouthpiece remove it separate it into three pieces. And soak it in your zeus purifyMoreTo clean the mouthpiece remove it separate it into three pieces. And soak it in your zeus purify cleaning solution for about half an hour then rinse and towel dry.
Can you use Xmax starry while charging?
A handy detail is that you can use the XMAX Starry 3.0 when charging. You don't have to wait until the battery is fully charged.
How do I use XMax V3?
How to use the XMAX V3 ProMake sure your battery is fully charged before using.Remove the magnetic mouthpiece and load the chamber with up to 0.15 grams of flower.Don't pack your bud in too tightly or it will restrict the airflow.Press the power button three times to turn the device on.More items...•
How do you use MAX II?
0:272:31X MAX II Pro Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour botanical or wax into the chamber using your su scoop or stainless steel tool respectively. IfMoreYour botanical or wax into the chamber using your su scoop or stainless steel tool respectively. If you are loading wax. Remember to insert the wax gun.
Why is my vaporizer not heating up?
If your vaporizer isn't lighting up, heating up, or creating vapor, then the problem might be the battery. Is your battery charged? A dead battery is a common reason for why a vaporizer won't work. Try fully charging your battery and then trying it again.
Why is my vape sticky?
Condensation Buildup. The most common cause of a clogged cart is condensation buildup inside the cart's airway. Over time, this condensation can block the mouthpiece, preventing vapor from passing through as you take a hit.
How often should you clean a vaporizer?
It should be cleaned at least every month, but regular users should clean it more often, as much as once per week. A nice, quick clean will keep your vape working up to its potential, free of built up debris and general resin-nastiness.
Can I smoke my vape while charging?
Some vape kits have 'pass-through technology', which means the device can be used while it's on charge. Some examples of devices which have this feature are the Innokin Endura T20-S, the blu Ace and the Joyetech eGo AIO D22.
Can I use my phone charger to charge my vape?
It's always best to use the same cable that came with your device to charge your vape. Most phone chargers are fine, however some phone chargers where the cable cannot be removed from the charger are designed specifically for the product they came with.
What is pass-through charging vape?
Passthrough charging is the glorious feature that allows you to plug your completely dead device into the charger and use it immediately – while it charges on the charger. The key difference is the ability use it while it charges, not just using it while plugged into the charger.
How do I charge my XMax V3 Pro?
Charging your XMax V3 Pro To charge the device, insert the USB cable provided into the micro USB port on the bottom of the device. An initial charge will take approximately 1.5 hours. It is not recommended to use the device while it is charging to avoid damage to the battery.
How do I charge my XMax V2 Pro?
The X-Max V2 Pro can be charged with the included Micro USB cable. Plug it into an AC adapter and let it charge up! The XMax V2 Pro takes about two hours to charge from empty to full.
How do you use the V2 Pro vaporizer?
0:163:51V2 Pro Series 3 Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo unlock the series 3 just press the activation button three times and the units LEDs will blinkMoreTo unlock the series 3 just press the activation button three times and the units LEDs will blink white. Next just press and hold the button when you're ready to start vaping.
How do you use the vape Planet 1?
Planet of the Vapes ONE Quickstart GuideFully charge the POTV ONE.Run a burnoff cycle.Grind and pack your herbs.Click the power button three times to turn on, and set the temperature.Once it vibrates, enjoy your session!When done, click the power button three times to turn off.Brush out the oven.
How to turn on Starry Vape?
To turn on the Starry, hold the power button for three seconds.The two smaller buttons adjust the temperature up and down, and it will immediately start heating up to the last temperature. The coffee cup icon will blink while it heats up, and turns solid when it’s time to vape.
How to get rid of the smell of Starry?
With the mouthpiece attached, turn the temperature all the way up to 464° F (240° C) and let it run until it shuts off on its own. Repeat this process three to five times, until any smell is gone.
How long does it take for Starry to charge?
Charging. Before you use your Starry for the first time, make sure to give it a full charge. This could takes as long as four hours the first time, with shorter charge times after that. We recommend plugging the USB cable into your phone’s wall outlet adapter for a faster charge.
How to make a vaporizer with a mouthpiece?
Put the lid back on, and swivel the mouthpiece out. For your first session, start with the heat set to 390° F, and take a light, slow draw, like sipping hot tea. You shouldn’t need to stir, but you may be able to get a little bit more vapor with a stir near the end.
What is the XMax Starry v3?
The X-MAX Starry v3 is one of the latest portable vaporizers by X-VAPE, the creators of the community favorite X-MAX V2 Pro. X-VAPE is known for their reliable and affordable vaporizers, and this dry herb vape is no exception.
How to Use the Starry V3
Using your new Starry vaporizer is quick and easy, and we’re here to help you through it. Our handy user guide covers all the details you need to get the best hits from your device.
Cleaning the XMax Starry V3
It’s important to regularly clean your vaporizers. If they get too dirty, it can impact flavor and performance. Luckily, cleaning the Starry is a breeze and only takes a few minutes.
Pros and Cons of the Starry Vaporizer
Pocket friendly: The Starry measures in at a slim 4.3"H x 1.37"W x 0.94"D - about the size of an average candy bar. It easily fits into your pockets, purse, or backpack, and it’s discreet enough to rip on the go.
Final thoughts
If you’ve ever ripped a dry herb vaporizer, you’ve likely heard of X-Vape. They’re a household name for a reason, delivering consistent, reliable vaporizers at affordable price points. The X-MAX Starry V3 continues in this fashion, fusing form and function in a discreet pocket-sized vaporizer.
Can't get enough PuffItUp?
Thank you for reading our blog! Check out our Instagram page and please tag us in your vape pics. If you want to start a discussion, throw up a post on the /r/PuffItUp Subreddit. Want to chat with the PIU community? Come drop us a line in the official PuffItUp Discord channel.
How to disassemble Starry?
Start disassembling the Starry by removing the mouthpiece, and taking the metal screen from inside the oven. Pull the rubber gasket and ceramic screen from the bottom of the mouthpiece, and pop out the black ceramic screen inside. You can use the paper clip, or a similar poker, to remove the metal screen from inside the ceramic piece. You can disassemble the upper half by sliding the metal plate towards the center, which will release the mouthpiece stem. There’s a gasket on the stem that’s easy to lose, so watch out for it when the stem falls out.
What does "clean Xmax starry" mean?
Our cleaning and maintenance guide will show you how to clean your XMAX Starry and have it looking brand new. A clean vaporizer means a happy vaporizer owner , and the XMAX Starry is no exception. When it’s clean, it’s easier to use, the vapor tastes better, and it’s more efficient.
Can you soak a vaporizer?
You should never soak, submerge, or wet the main vaporizer unit. All of the pieces from the mouthpiece should be soaked only in warm, soapy water. After a nice soak and a few good stirs, rinse everything in hot water until there’s no soap smell left, then dry everything completely.
