Holding your squonk mod in your hand, gently press the juice reservoir. Pressing the reservoir will squeeze your e-liquid up and out of the reservoir into the hose. The juice will be pushed through the hose into your bottom feed squonk RDA, soaking the coils and filling the juice well (area beneath the coils).
Full Answer
How do I get Started with vape squonking?
If you’re starting out on vape squonking, you may need time to adjust to the setup. For example, RDAs hit dry. You’ll also need to become familiar with how much pressure you should use to squonk on your mod to ensure the coils are thoroughly soaked, or you’ll get a burnt taste.
What is a squonk vape?
Although similar to standard vaping, squonking isn’t quite as automated as your traditional device. Transferring the e-juice from the bottle inside to the RDA requires a bit of a helping hand. Unlike your typical sub-ohm tank where the cotton wick is soaked automatically, squonk mods operate a little bit differently.
Can you use an RDA with a squonk vape?
Squonk mods are limited to using RDAs because of their bottom-feeding pins. The bottom-feed pin feeds juice from underneath the atomizer. When buying a regular RDA for your squonk vape, you’ll want to make sure it comes with a bottom-feed 510 pin. Otherwise, the juice will squirt through the hose and into your device.
How do you smoke extracts in a portable vaporizer?
The method you use to smoke extracts in a portable vaporizer depends on the specific model you’re using. If you’re using a disposable, pre-loaded pen, just puff away until you’ve used it all up. Then toss it and get another one.
How do you use a squonk vaporizer?
The e-juice reaches through pressure from the beneath squonk bottle in the RDA by pressing or squeezing the squonk bottle. Hit the power button on your mod and just take a puff. You are all set to start squonking. After a few puffs, you must squeeze the bottle to keep the wicks coated and the vape free from dry hits.
Is Squonking the best way to vape?
Squonk mods are definitely not suitable for those new to vaping. However, if you enjoy vaping on RDAs and don't want to carry vape juice bottles around — or maybe you just don't always feel like dripping — then yes, you should get yourself a squonker.
How do you wick a squonk?
Cut into the side of the box is a 'squonk hole', which allows you to squeeze the bottle. This pushes e-liquid into the dripper from below. As you squeeze e-liquid is pushed up, saturating your cotton and wick without having to drip into the top. As you release pressure any excess runs back into the bottle.
Why is it called a squonk vape?
First off, what is a squonk box? Also known as bottom feeder mods, squonk devices are vapes that have space for a bottle of liquid tucked inside the shell of the mod, alongside the space for the batteries.
What is the point in a squonk mod?
A squonk mod features a built-in squeeze bottle. This allows the vape juice to pass through the aforementioned feeding hole to the atomizer. Sometimes, a squonk mod is made with an RDA that has been modified. With its inner squeeze bottle, the squonk mod takes away the need to drip the vape juice.
What is the RDA for Squonking?
1. Hellvape Hellbeast RDA (Editors Choice) One of the most popular brands when it comes to RBA's is of course Hellvape and they have certainly done nothing to harm that reputation with the Hellbeast RDA. This dual coil, 24mm diameter RDA is squonk compatible and has nailed the airflow (72 holes!)
Are squonk mods good?
Squonk mods have become a huge hit in the vaping world because they're naturally the next step for any vaper using an RDA. Due to their added convenience and utility, squonk mods make using an RDA less cumbersome and more portable.
How do you properly Wick?
The best way to thread your wick is to tightly roll one end of your wick down to a point so that it can be threaded through like a needle. Your wick should be 2-3 inches long so you should have plenty of room to roll one end while leaving the center of your wick loose enough to fill the coil.
How do you rewick vape?
0:546:31My Two Methods For Re-wicking An RDA Perfectly Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull it through make it even both sides there we are and it shouldn't be too tight if it's too tightMorePull it through make it even both sides there we are and it shouldn't be too tight if it's too tight you're going to manipulate the shape of your coil.
Who invented Squonking?
Initially called the JuiceBox, Carlos49's model didn't take off. For one, the integrated atomizer cannot be serviced without returning it with the modder. And secondly, there was too much demand. The term “Squonk” was then coined and attributed to another forum member, Jack Murray, and it stuck to this day.
Can I use a squonk RDA on a regular mod?
However, using a regular mod with a squonk RDA is a very bad idea. Squonk RDA's have a hole in the 510 thread that could allow e-liquid to fall through. This could potentially damage your mod's hardware.
Are squonk mods regulated?
Regulated Squonk Mod Regulated squonk mods have variable wattage and voltage chipsets that allow the vaper to adjust the power and temperature settings. Regulated mods have various safety features that unregulated mods sometimes lack.
What is vaping technology?
Vaping is an amazing technology that opened the door to innovation beyond anything we could’ve imagined. We always love to see new advances in this area, but adjustments bring new challenges.
Is squonking fun?
However, it’s not all fun and games. While this method is certainly revolutionary, it requires surgical precision.
Is squonking safe for vaping?
If you’re curious about squonking, then we say “go for it”. But if you’re new to building (or vaping in general), then squonking is definitely not for you (yet). Many aspiring vapers are painfully aware (some more painfully than others) of the dangers associated with incorrectly built or unregulated mods.
Does squonking require a mod?
Keep in mind, however, that squonking doesn’t only require the purchase of a brand-new mod. It also calls for a specific RDA that has a feeding hole drilled into the center post for liquid to pass through (see below).
Is squonking still in its infancy?
Unfortunately, squonking is still in its infancy. The advanced nature of this niche means that vape companies really haven’t had a chance to embrace this new technology and meet its increasing demand. Consequently, many of the pre-built squonk mods on the market today are unregulated.
Is squonking safe for vaping?
Squonking is one of the biggest trends to hit the vaping community – and yet, there’s still a considerable amount of mystery surrounding this popular vape style. For many vapers, both new and advanced, “squonking” is a vape term they may have heard in passing, but never actually experienced for themselves. You may have come across cautionary tales while Internet searching for answers to questions like “what is squonking” and “is squonking safe,” or might have even heard about less-than-stellar squonk experiences from a fellow vaper. On the other hand, you’ve probably heard talk about the potential to take your vape experience to the next level with squonking – so what’s the deal with it, really?
Is squonking worth it?
Even though squonking requires a bit more effort than traditional vaping, most squonk loyalists insist that it’s worth it for the flavor quality alone.
What is Squonking?
Squonkers, aka bottom feeding RDAs, deliver e-juice directly to the atomizer through the bottom by way of a tube. There is a squonk hole located in the device, which you squeeze to push the e-juice up through the tube and into your atomizer, soaking the wick full of flavor.
Is Squonking Right for You?
Although there are plenty of benefits to squonking, it’s not for everyone—at least, not at first. If you’re relatively new to the vaping world, there are still some important things you need to master first before tackling squonking. Squonkers can be both regulated and unregulated.
Popular Squonk Mods
So, you’re tired of dripping your atomizer all the time and want to start squonking. Which squonk mod is best for you? While the answer to this will depend on your vaping preferences, we’ve rounded up a list of popular squonk mods worth considering:
The Bottom Line
While there are plenty of beginner-friendly squonk mods on the market, it’s essential that you know your way around RDA devices well before trying a squonk mod. This includes how to properly maintain coils and tanks, as well as a working knowledge of Ohm’s Law and battery safety.
What is the difference between a squonk and a vape mod?
The main difference between your standard vape mod and a squonk mod is that the latter contains a juice reservoir inside the device, instead of on top. The mod will have either a cut-out section or a button/lever that allows you to press the reservoir, soaking the cotton of your RDA on top of the device.
What is squonking in vaping?
Squonking is what’s used to describe the act of pushing on ...
What is a squonk mod?
Squonking is a vaping method that uses a vape mod called a squonk mod. A squonk mod contains a juice reservoir inside and has an opening or button that allows you to squeeze on that reservoir. When you push on the reservoir (or ‘squonk’), juice will be pushed up through a little hose into a bottom-feed RDA, an RDA with a hollow 510 connection pin ...
What pins do you need to use for squonk mod?
When buying an RDA for your squonk mod, you’ll want to make sure that it comes with a bottom-feed 510 pin; otherwise, your juice will squirt through the hose and into your device (possibly causing damage).
Where is the battery housing in Squonk?
Located next to your juice reservoir will be the battery housing, with most squonk mods only making use of a single battery. Squonk mods are limited to using RDAs because of their ability to use bottom-feeding pins. These are pins that allow juice to be fed from underneath the atomizer, instead of on top.
Can an unregulated mod cause a leak?
With an unregulated mod, the battery can vent , which can cause it to leak battery acid, smoke, or even explode, if you’re not careful. If you’re new to vaping, you’ll definitely want to look for a regulated mod; this can help you get used to building coils and maintaining your device without the dangers of hurting yourself.
Welcome to the world of vaping
Marijuana is moving into the mainstream. And that’s opening up all sorts of new possibilities. One of the most important is the marriage of weed with tech. And nothing else is pushing the envelope as much as vaporizers. Vaping has actually become its very own sector in the smoking world.
Why Vape?
The main reason for vaping, as opposed to smoking, is to get a cleaner final product. When you smoke weed you’re obviously getting tons of THC. And in case you forgot, that’s the stuff that actually gets you high.
Different Types Of Vaporizers
The wide world of vaporizers can be broken down into two main types: desktop and portable. We’ll start with desktop vapes.
Vaporizer Components
The world of vaporizers can be broken down even further. That’s because there are actually different types of desktop and portable vapes.
Flower Or Extracts?
Clean vapor isn’t the only thing vapes give you. They also give you flexibility. That’s because you can find vaporizers that use whatever form of cannabis you like best.
How To Smoke A Vaporizer (Desktop) With Dry Herb
To smoke a whip-style desktop vaporizer with flower, follow these steps:
How To Smoke A Vaporizer (Desktop) With Extracts
Most desktop vaporizers use a similar process for vaping oils, waxes, and other extracts. The chamber will usually come with a piece for extracts. It’s usually a mesh screen that goes into the loading chamber.
Step 2: Front and Back Panel
For the front and back panel of the mod I used 3mm thick walnut. I have access to a laser cutter, therfore I cut them out and engraved them using this machine, but you can also use a coping saw or something similar to cut them out. Alternatively you can also print the front and back panels with your 3D Printer or again get them printed at shapeways
Step 3: Copper Contacts
Since this is a purely mechanical mod, I used a 0.5mm thick piece of copper for the contacts of this mod. You can either cut them out yourself or get copper contacts on a website called www.modmaker.co.uk and make them fit. Therefor again I made a template to get the correct shape.
Step 4: Parts From Modmaker
Last but not least you are going to need a few more parts from modmaker. A detailed parts list can be found here: Parts List
Step 5: Done
Do you have any more questions or ideas how I could improve this instructable? Feel free to hit me up.
