Step 1 - Prepare your device Remove your device from the box and place it on a flat surface in front of you. Step 2 - Fill your tank or pod with e-liquid
Full Answer
How to fix check atomizer on a pod vape?
How to Fix Check Atomizer/No Atomizer On A Pod Vape. 1 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points. 2 2. Check Your Contact Points for Damage. 3 3. Reseat your Coil/Pod. 4 4. Try Another Coil/Pod.
Should I keep the user manual for geekvape products?
Keep the user manual… Post Views: 38,034 Thank you for choosing GEEKVAPE Please read the user manual before using this product for better user experience. Keep the user manual… Post Views: 3,337 Thank you for choosing Geekvape Product Please read user manual before using this product for better user experience.
Does aegis legend atomizer work with Atomizer?
When we use any Atomizer, Aegis Legend works fine. However, we can… Post Views: 91,611 How to Use Aegis Legend Kit? The device “Geekvape Aegis Legend Kit” is water and dust resistant and was tested under conditioned.…
How to turn on geekvape aegis legend kit with Zeus tank?
Turn on: Press the Fire button 5 times in… Post Views: 15,165 GeekVape Aegis Legend Kit with Zeus Tank actually is GeekVape Aegis Legend Limited Edition. A stronger and powerful Kit! But do you… Post Views: 2,993 Thank you for choosing Geekvape Please read the user manual before using this product for better user experience.
What does it mean when the fire button on a atomizer doesn't work?
If you press the fire button but the device does not fire, 1.If the red light flashes 3 times, it means that there is no atomizer connected, please change another pod or replace the coil and try again. 2.If the red light flashes 5 times, it means the battery is too low, please charge the battery full and try again.
Why is my e juice not turning into vapor?
The e-juice in that instance is too thick for your low wattage device and coil, therefore the e-juice doesn't heat sufficiently to turn into vapor. The more common reason is that you've flooded the coil when priming, excess juice in the coil which can't vaporize quickly enough results in gurgling and/or spit back.
What is ABB battery balance?
ABB：Auto Battery Balance. When activated, the device would balance your batteries by sharing some of the chargers from the highest charged to the least charged battery. (Click here to watch a video about it)
Why does my vape spit back?
Other possible reasons for spit back may include the following: using high PG e-juice in conjunction with a sub ohm coil, chain vaping from a tank which gets fairly hot as the heat thins your ejuice, a coil which is wicking the cotton too quickly.
How to fix a sub ohm tank leak?
Here are some tips to avoid leaking: 1.Please close the airflow holes when you refill the tank, and do not saturate the coil directly with juice dropping to the inner coil, you just need to fill the tank and wait around 10mins.
Is Aegis shockproof?
As we all know Aegis lines are waterproof, shockproof, and dustproof. This article will talk about the waterproof feature of the Aegis lines. To know more about the product's shockproof feature, please click here. IP67 waterproof is able to withstand immersion for up to 30 minutes and at a depth of up to 1 meter.
Why is my atomizer checking?
Sometimes a check atomizer error can be caused by your coil. If cleaning your contact points didn’t work then you can try reseating your coil. You’ll want to take apart your tank as if you were changing the coil. Unfortunately, this can be a little bit messy and isn’t always convenient to do if you have a considerable amount of ejuice left in your tank.
What causes a check atomizer short?
Loose pieces of metal on the build deck will cause your mod to display “Check Atomizer” or “Atomizer Short”. Even very small pieces or trimmings of wire can cause a short or a check atomizer error on an RDA/RTA/RDTA. First, inspect the build deck closely for loose pieces of wire or other foreign objects.
What to do if your pod vape isn't firing?
If your pod vape isn’t firing, has a blinking LED and won’t fire, or says Check Atomizer or No Atomizer, you can follow a few of the same steps listed above for tanks: 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points.
Why is my mod reading the new tank correctly?
If your mod is reading the new tank correctly, it could be a problem with the coil on your other tank. You might also want to clean the contact points on the tank that was giving you the error. If your mod is still reading “check atomizer” with a new tank, it’s probably a problem with your mod.
How to reset 510 pin on a mod?
Take a screwdriver and gently push down on the 510 connector inside of the mod. This can help ‘reset’ the pin and allow it to spring back up. But if this doesn’t work there isn’t much else you can do.
How to remove a tank from a mod?
Start by removing the tank from the mod and inspect the threading where the tank screws in for dirt , dust, or ejuice. Do the same with the 510 connector on your mod. Clean out the contacts with a paper towel, and screw your tank back onto your mod.
Can vaping happen without cause?
All vapers will experience this problem at some point in their journey, and it can happen suddenly and without any apparent cause. Thankfully, while a bit frustrating, this is an easy problem to fix.
