What should I do if my Smok vape won't turn on?
If your SMOK vape isn’t turning on, it could be a quick fix: 1 Try charging your mod to see if a dead battery is an issue. Plug it into the charger and hope that you forget to... 2 Check the battery to confirm that it’s properly inserted. Depending on your model, you might be able to pull out the... More ...
How do I Turn my vape pen on or off?
Power – Most vapes have a 3 or 5 click feature to turn them on. It is important to make sure to remember to turn off the pen with the same number of clicks as well, as it is impossible to easily to tell if the pen is still on or off.
How do I know if my vape is in Watt mode?
Sounds like you maybe set it to temp instead of wats, hit it 3 times til you get to the fit screen, hit 1, 2, or 3, 1 for battery 2 for clouds and 3 for flavour, then see if the number gets a W next to it if it does this means your in wattage mode which is where you wanna be if your vaping juice.
How to fix Smok error messages on a vape?
Try screwing your tank in a little bit tighter and clearing off any dust from the 510 connection and the connection point. “Short Atomizer” or “Don’t Abuse Protects” Seeing either of these SMOK error messages is a big red flag, and you should immediately stop vaping for your safety.
How do I reset my vape mod?
Reset the tank - You can 'reset' the tank by removing it from the mod, checking the screws are tight and pressing the fire button. Then re-attach your tank and select “n” when you are asked if it is a new coil.
How do you reset the puff on a vape counter?
0:322:03Puff And Time Counter Reset - WISMEC RX Gen 3 ReuleauxYouTubeStart of suggested clipEnd of suggested clipAnd you see the puff counter resets to zero from there we're going to do the same for the time. SoMoreAnd you see the puff counter resets to zero from there we're going to do the same for the time. So again push the power button three times push the left button.
Why will my vape not turn on?
It needs a new battery You may even find that the battery inside your device needs replacing. Most vape batteries will have a lifespan and they will need to be replaced over time.
How do I factory reset my Geekvape?
Restore Factory Settings: When the device is turned off, press and hold "+" and "-" button at the same time, the screen will display firmware version number, and then press and hold fire button, "+" and "-" button all at the same time to restore factory settings, a prompt as "CONFIG RESET" will be displayed on screen ...
How do I reset my Smok puff?
You can set the "puff clear" or "puffs reset": Click "No"= Quit resetting the puff, you will not be able to vape; Click "Yes"= Puff data will be set to 0.
How do you reset Smok Nord 4 puffs?
Device On/Off – Press fire button 5 times in 2 seconds. Puff Reset – Number of puffs will reset when you reach 999.
How do I get my vape to work again?
The best way around this problem is to vape with one of your fingers around one of the inlet vents. This increases the airflow pressure and might get the sensors up and working again.
When I press the button on my vape nothing happens?
Try cleaning the battery terminal and end of your clearomiser with a cotton bud. Another thing to check is that the tank or clearomiser is making contact with the battery terminal. If a previous tank has been screwed on too tightly, the battery pin may need adjusting to make a connection again.
How do I turn my vape back on?
Turning on Your SMOK VapeFirst, locate your device's main fire button, which also functions as the power on/off button. ... Once your device is unlocked, press the main fire button three times to access the device menu. ... After you've enjoyed a good vape session, turn off your SMOK device by accessing the menu system again.
How do you reset Aegis hero vape?
Aegis Hero Button Combinations Press the adjustment buttons to select mode and hold the fire button down to select. Clear Puff Counter: press the fire button and down the adjustment button. The puff counter will be highlighted. Press the down button again to clear the puff counter.
How do I reset my GeekVape Aegis boost?
Hold down the UP and DOWN button together to lock the settings. Hold DOWN & Fire buttons to reset puff counter. Three Clicks of the FIRE button locks the mod from firing.
How do I reset my GeekVape obelisk?
To reset all user configurations for the Obelisk miner, press and hold the button on the front of the device for 10 seconds.