Switch over to Temperature Control mode, whether this be navigated through the menu system or a specific button, and pick the correct wire type (SS, Ni or TI). Set your temperature limit, which should be decided by taking into account wire type and your wattage output.
Full Answer
How do I get temperature control on my vape?
Different vape devices and kits access Temperature Control mode differently, yet the process is largely the same. First off, attach your tank or rebuildable atomiser to your device. Then check that the wattage output of your device is within the defined limits of what your coil can handle, this is usually written on tank coils.
What is temperature control (TC) in vape mods?
Temperature control (TC) in vape mods is a technological solution for dry and burnt hits. It also creates a consistent vape while taking longer drags because the temp stays the same—instead of getting hotter.
How do temperature control vape coils work?
The power sent to the coil then automatically adjusts to keep the coil—and your vape—at the chosen temperature. It all began with the creation of the DNA chip by a company called Evolv in 2014. Even now, many still consider mods with DNA chips to be the best temperature control mods on the market.
How does temperature affect vape wire resistance?
When you vape with Kanthal (the most popular vape wire), that resistance value doesn’t change. That’s a particular property of Kanthal: its resistance is static regardless of its temperature. For TC vaping, you’ll use wires that have a known resistance-increase as their temperature rises.
How do you set the temp control on a vape?
How to vape in TC. Put your mod into TC mode and select the corresponding wire type for the coils you have. If the mod has a TCR you can enter the exact TCR value. After that, ensure that your mod and tank are both at room temperature so the temperature readings will be more accurate.
How do I reset my Smok vape?
Reset the tank - You can 'reset' the tank by removing it from the mod, checking the screws are tight and pressing the fire button. Then re-attach your tank and select “n” when you are asked if it is a new coil.
How do you reset a vape coil?
How to clean your CoilLet your coil soak in ethanol, vinegar, or cheap vodka for at least a couple of hours.Place it under the tap and rinse.Rinse once more with some distilled water.Blow air on the open side of your coil to force water to the wicking holes.Set it aside until all water has evaporated.
What does TCR mean on my vape?
Temperature Coefficient of ResistanceThe Temperature Coefficient of Resistance (TCR) This specific TCR value of the wire is kept in mind by the vape mod, allowing it to adjust the amount of power being sent to the coil and thus control the temperature.
How do you reset a SMOK Nord 4?
Device On/Off – Press fire button 5 times in 2 seconds. Puff Reset – Number of puffs will reset when you reach 999.
How do I reset my Smok RPM 2?
Usage is pretty simple too. The RPM2 Pod has the usual 5 clicks off/on, as well as 3 clicks of the fire button to lock the device. Holding down both up and down buttons locks and unlocks the wattage. Holding the Power and down buttons allows you to reset your puff counter.
Why is my coil burning after 1 day?
That burnt taste can occur if there's not enough e-liquid on the wick inside your atomizer coil. The wick is the part of your device that soaks up the e-liquid, which is then turned into vapour when the coil heats up.
Can a burnt vape hurt you?
Depending on how bad the coil is burnt, you could end up choking or vomiting immediately. Depending on what kind of coil you are using they can produce some particles that stick to the vapor and end up ingested by the user when they are burned dry. Some have an allergy to these particles being created.
Why does my coil taste burnt after 2 days?
It tastes burnt because the wick inside your atomizer coil has dried out and burned up when it was heated. The wick is the part of your vaporizer that soaks up the eliquid from the tank. The wick holds onto this eliquid before it is turned into vapor when the coil heats up.
What wattage should I vape at 0.2 ohm?
0.3 ohms - 40 watts to 90 watts. 0.2 ohm coils - 40 watts to 100 watts.
What wattage should I vape at 0.4 ohm?
23 - 28 wattFor example, a 0.4-ohm mod may recommend a 23 - 28 watt setting, and a 0.8-ohm mod may recommend you use up to 35 watts. Some recommendations can go much higher (e.g., 200 watts). Sub-ohm devices work best when using a high VG vape liquid (e.g., a VG/PG ratio of 70/30).
What wattage should I vape at 0.15 ohm?
60-90 wattsIn contrast, the 0.15ohm dual mesh coils have a best recommended wattage of 60-90 watts. Both atomisers offer huge clouds and flavour production. Since these coils are sub ohm / direct to lung (DTL) in vaping style, they are recommended for use with higher VG e liquids.
Choosing Coils
Today, there are a wide range of coils available specifically for temperature control devices. For the most part, you will be working with Ni200 or Stainless Steel (SS316L) coils. Hopefully, you checked your device before you brought it home to ensure you have the correct type of coils on hand.
Selecting Your Mode
The next step in your setup process is to select the temperature control mode you will be using. Depending on your device, this can go several different ways. You may need the assistance of your user manual to figure out the menu for the first time.
Base Settings
In order to ensure that your device is functioning properly and that all temperature control operations are accurate, you first need to lock in your resistance at room temperature. Setting a base line temperature without electricity going through the coil will establish all temperature sensing as your coils heat up.
Getting in the Groove
If you are working with a high powered device like the Vex 150 TC Mod, you have plenty of room to work with, so start slow and take your time. At each interval, stop and take a few hits.
For Next Time
Now that you have set up your temperature control device successfully for the first time, you’ve got a good feel for the way it’s done. It may be slow going at first, but you will get familiar with the menu quickly and soon you will have a good idea of what settings give you the best results so you can narrow down your search for the perfect vape.
What is temperature control vaping?
Temperature control vaping can be an amazing experience. It provides the security of consistency that wattage vaping often lacks. No one likes dry or burnt hits, or vapes that get too hot with long hits. TC vaping solves that.
Why is my vape consistent?
Vape consistency: By having control over the temperature your coils can rise to, the vape will be consistent from puff to puff, and even within one puff. In regular wattage mode, the hits are more inconsistent because the heat of the coil changes based on the length of the hit.
What is the best wire for vaping?
TC vaping generally uses one of these four types of vape wires: 1 Stainless steel: this wire is very popular and readily available. It comes in various grades such as 304, 316, 316L, 317, and 430 but the most common is SS316L. SS can be used in wattage or temperature control mode. 2 Nickel 200: commonly known as ni200, it was the first temperature control coil but it’s less common now due to some vapers having sensitivities to nickel. 3 Titanium Grade 1: otherwise known as Ti. It works well in TC but the user has to make sure it does not get overheated. 4 Nickel ferrous: also known as NiFe, comes in various grades such as 48, 30, 52, 70 and can be used in either mode, but is not widely available.
What type of wire do you use for vaping?
Next, you must vape with the right wire type. TC vaping generally uses one of these four types of vape wires: Stainless steel: this wire is very popular and readily available. It comes in various grades such as 304, 316, 316L, 317, and 430 but the most common is SS316L. SS can be used in wattage or temperature control mode.
Do vape mods have TC?
First and foremost, a vape mod that supports TC. Most mods on the market come with a TC mode, although it is often left out from otherwise fully capable pod mods. If unsure, check the specs before buying a mod—or use the search function on this website. If a vape mod does TC, we will test it!
What is the advantage of TC mode?
In TC mode, if the wick runs dry the temperature will start to rise, and therefore the temperature protection will immediately cut power to compensate.
Can you adjust wattage on a vape mod?
Prior to TC, most top vape mods could only adjust watts (another innovation from Evolv a few years prior.) Now in 2020, like wattage control, temperature control is a feature found in most vape mods.
What is the best battery for a vape pen?
The thicker vapor does come at a cost. It uses up your concentrates faster and requires more battery power. The best vape pen batteries are Lithium-ion. These have a higher energy density and can better handle the energy requirements of medium-temperature vaping.
What temperature do dabs need to be?
Medium-temperate dabs use a range between 450℉ and 600℉. It creates a bigger vapor cloud, but delivers less flavor than the lower temperature setting. It’s a good in-between option for people who care about taste but prefer thicker clouds.
What is oil pen?
Oil pens are the fastest-growing segment in the legal cannabis market. Their convenience, discretion, and portability have all contributed to their popularity. But one of their biggest benefits is that they offer a greater degree of control.
What is the boiling point of cannabis?
To be able to vape, the boiling point is the minimum temperature. The boiling point for the most popular cannabis oils are: THC Oil: 315℉. CBD Oil: 356℉.
Is it safe to vape at high temperature?
High-Temperature Vaping. High-temperature vaping is not recommended. It is not as safe as vaping at low or medium temperatures. As well, the flavor quality is poorer and the experience is less reliable.
Does low temperature vapor have less flavor?
This setting produces a thinner vapor than higher temperatures. But thin vapor doesn’t mean less flavor. In fact, the low-temperature vapor is actually the most flavorful. The flavors and aromas in cannabis vapor come from the terpenoids (terpenes) within.
What does a shift in coil resistance mean?
Instead, they measure the changes in your coil’s resistance. When a coil heats up its resistance generally increases your kit will track these changes and assign a temperature value to them. For example, a shift in resistance from 1.1 Ohm to 1.2 Ohm can mean an increase in temperature from 120 to 130 degrees Fahrenheit.
Why is it important to keep coils in good condition?
Keeping your coils in good condition also means that you can maximise their lifespan, for a more cost-effective experience overall. The option of programming a temperature also gives you control over the style of vape you’ll experience. A lower temperature can be used to experience a longer, cooler inhale; whereas a higher temperature can be ...
Why do you need TC vape?
The major benefit of TC vaping is that it stops your coil from running too hot. This in turn ensures your coils last longer as they won’t burn out prematurely, while also making sure your RDA/tank avoids any damage. Keeping your coils in good condition also means that you can maximise their lifespan , for a more cost-effective experience overall.
Do you need TC mode for Kanthal?
You’ll need a kit or mod programmed with TC mode in order to experience Temperature control vaping. As well, you’ll also need compatible coils. The majority of vape coils use Kanthal in their construction, Kanthal does not work with TC mode as its resistance does not change when it heats up.
Do coil wires react to heat?
Different coil wire types will react to heat and their resistance will increase at a different rate. It is for this reason that each TC mod and kit will have different modes available to support these common wire types. It’s always important though to always check compatibility and manufacturer guidance before use.
What is a Temperature Control Mod?
Temperature Control is the vape industry's solution to dry and burnt hits. It keeps a consistent vape when taking longer drags since the temperature remains the same rather than getting hotter. The user chooses the temperature limit and the power sent to the coil automatically adjusts to keep the coil at the chosen temperature.
How Does Temperature Control Work?
Temperature Control works as the metal of certain mods increase the resistance as they heat up. However, if you vape with Kanthal, which is the most popular wire type, the resistance doesn't change, it remains static no matter the temperature.
What Do You Need For Temperature Control Vaping?
First, you need a mod that allows you to control the temperature. You can buy a temperature control mod here. There are a number of differences between the devices, with some coming with special and advanced features. Some mods do a better job at controlling the temperature than others do.
How to Vape in TC Mode
Put your mod in temperature control mode and pick the matching wire type for your coils. If your mod has a TCR, you can enter the exact value. After, make sure both the mod and the tank are at room temperature so the measurements are more accurate. The simplest way to accomplish this is by not using the kit for 15 minutes before starting.
Best Vaping Temperatures
A common vape temperature is in the range of 200 to 250 °C with the temperature adjusted quickly in increments of 5°C.
Pros of Temperature Control Vaping
Stops burnt/dry hits - While there are many ways to stop dry hits, temperature control is probably the best, since it does it automatically. If the wick runs dry, the temperature will rise and the temperature protection will cut power to compensate. As a result, you just get less vapour rather than a dry hit.
Cons of Temperature Control Vaping
More Complicated - Unlike some vapes, temperature control vapes require you to do some trial and error to get the perfect temperature.
How long do temperature control coils last?
Rather than being replaced weekly, if used correctly, temperature control coils can last a month or more. Advertisement.
What happens when a coil is in temperature control mode?
When the coil gets to a certain point in resistance change, the device it’s attached to (if it is in temperature control mode), will either cut off the power, limit the power, or adjust it to keep a constant output.
What is the guide to vaping?
Guide To Vaping is the largest online magazine blog that is dedicated to providing a vast selection of helpful and informative articles about the latest vaping news, vapor products, and CBD.
ObsceneJesster Super Member ECF Veteran
So I'm pretty new to temp control and I don't know what's going on but I'm trying to vape a Ni200 coil in a Crown Tank on top of a Kanger K-Box 70w. I am switching into Ni mode but after firing it, the mode keeps switching back into Wattage.
crxess Grumpy Ole Man Verified Member ECF Veteran
So I'm pretty new to temp control and I don't know what's going on but I'm trying to vape a Ni200 coil in a Crown Tank on top of a Kanger K-Box 70w. I am switching into Ni mode but after firing it, the mode keeps switching back into Wattage.
ObsceneJesster Super Member ECF Veteran
Now all of a sudden after 3 hours of the coil having a resistance of .35, it now is reading at .16 and the K-Box is allowing me to vape in Temp Control mode.
crxess Grumpy Ole Man Verified Member ECF Veteran
it just goes back and forth from normal to nickle without the titanium option.
crxess Grumpy Ole Man Verified Member ECF Veteran
On the RX, it supposes to round robin from wattage to ti to ni and so on, but for this one, it just goes back and forth from normal to nickle without the titanium option.
FoundedInsanity New Member
Hey Guys quick question. I am using a Indestructible Addy with TI sweet spot .5 mm wire. Its a dual coil 6 wrap registering at .24 ohms. It keeps kicking back into wattage mode. Even after locking resitance. Any thing I could be doing wrong?
edyle ECF Guru Verified Member ECF Veteran
Hey Guys quick question. I am using a Indestructible Addy with TI sweet spot .5 mm wire. Its a dual coil 6 wrap registering at .24 ohms. It keeps kicking back into wattage mode. Even after locking resitance. Any thing I could be doing wrong?
