Learning how to perform a SMOK factory reset for Alien, ProColor, Priv V8, and other mods’ tanks is a handy skill to have. First, altogether remove the tank from the mod, making sure its screws are tightly fastened. Press the fire button, then reattach the tank.
Full Answer
How do I perform a smok factory reset?
Learning how to perform a SMOK factory reset for Alien, ProColor, Priv V8, and other mods’ tanks is a handy skill to have. First, altogether remove the tank from the mod, making sure its screws are tightly fastened. Press the fire button, then reattach the tank. Choose “n” when the device asks if you are using a new coil.
How do I Reset my Smok puff counter?
Reset the puff counter by selecting “puff clear” on the mod’s navigation menu. “No Coil” Using a mod without the coil attached can cause serious damage, which is why SMOK implements this error message as a safeguard for your mod.
How do I change the coil on my Smok mod?
When you change the coil on your tank, especially if you’re using an RDA, the SMOK mod will ask you if it is a NEW or OLD coil and give you two potential Ohms readings. Select the one that is the same as your coil – if it’s new, basically, just hit the NEW option. On a touchscreen SMOK mod, simply tap the NEW option.
What should I do if my Smok vape won't turn on?
If your SMOK vape isn’t turning on, it could be a quick fix: 1 Try charging your mod to see if a dead battery is an issue. Plug it into the charger and hope that you forget to... 2 Check the battery to confirm that it’s properly inserted. Depending on your model, you might be able to pull out the... More ...
How do you reset a vape SMOK?
Reset the tank - You can 'reset' the tank by removing it from the mod, checking the screws are tight and pressing the fire button. Then re-attach your tank and select “n” when you are asked if it is a new coil.
Why did my SMOK vape stopped working?
SMOK Vape Won't Turn On If your SMOK vape isn't turning on, it could be a quick fix: Try charging your mod to see if a dead battery is an issue. Plug it into the charger and hope that you forget to recharge after your last use. Check the battery to confirm that it's properly inserted.
How do you unlock Smok procolor 225w?
9:3814:54ProColor 225W TC by SMOK! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll the way up to 225. But does not around Robin five clicks will lock. It. And now you are unlockedMoreAll the way up to 225. But does not around Robin five clicks will lock. It. And now you are unlocked. And obvious if you want to turn it off you go into the menu.
How do I reset my SMOK RPM80?
SMOK RPM80 Pod Mod Display Functions Here's the info: Fire Button 5 Clicks – Device On/Off. Fire + Right Button = Display Colour Change. Fire + Left Button = Puff Count reset.
Why does my SMOK blinks 4 times?
Short circuit protection: If the LED detects a short circuit, it will flash 4 times and the battery will automatically shut down the output. Low voltage protection: When the battery capacity is lower than 3.3V, the LED light will flash 15 times and the battery will automatically shut down.
When I press the button on my vape nothing happens?
Try cleaning the battery terminal and end of your clearomiser with a cotton bud. Another thing to check is that the tank or clearomiser is making contact with the battery terminal. If a previous tank has been screwed on too tightly, the battery pin may need adjusting to make a connection again.
How do you lock Smok ProColor?
If you want to turn it off, you need to either go into the menu; click the firing button until you see the Power Off option and then turn it off there, or you can lock the device by pressing the firing button 5 times and then holding the fire button down for about 5-7 seconds while it's locked.
How do you unlock the power lock on a Smok vape?
3:508:23SMOK NORD 4 - Now with More Power! - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne two three and it's going to lock the entire device lock the wattage lock it so you can't vape itMoreOne two three and it's going to lock the entire device lock the wattage lock it so you can't vape it. And then if you want to turn it on or off will be five clicks one two three four.
How do I change my vape settings?
Typically, most vape pen batteries with a button turn on by clicking it 5 times. Most variable voltage 510-thread batteries will switch voltage settings by clicking it either 2 or 3 times rapidly. It's important to always read the vape pen instructions before using a new one.
How do I reset my SMOK scar 18?
Smok Scar-18 Menu5 clicks of the fire button will turn the device on and off. ... 3 clicks of the fire button will open the options to change settings.Once you're done changing settings, long pressing the fire button will exit menu.Press and hold Left/Right buttons to lock/unlock device.More items...•
How do I unlock my rpm80?
3:475:22FV Vape Show - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it locks it will tell you every time you do it you know it's locked. When you've got the symbolMoreAnd it locks it will tell you every time you do it you know it's locked. When you've got the symbol of a lock above the w symbol for watts.
How do you fix SMOK without atomizer?
RecapClean all contacts on battery/mod, tank or pod.Remove and reinstall the coil (after cleaning)Try a new coil.Check the 510 pin and see if you can adjust it (mods/tanks)Try another tank on your mod.Try another mod with your tank.Adjust base of coil carefully if you can (mainly sub-Ohm coils)
How to use a smok mod?
How To Use SMOK Mods: Installing A New Coil. When you change the coil on your tank, especially if you’re using an RDA, the SMOK mod will ask you if it is a NEW or OLD coil and give you two potential Ohms readings. Select the one that is the same as your coil – if it’s new, basically, just hit the NEW option.
How to change the color of the fire bar?
From the Home screen, Click THREE times on the fire bar. Click through the menus until you reach Screen Setting. Use the buttons on the mod to move through the options until you find the color you want. Once you have the color you want, hold the fire bar for ONE SECOND. Done.
Can you fire a mod with homemade coils?
If there are any issues and/or problems with the coil, its resistance, or the connection, the mod will simply not fire and likely show an error message.
Does Smok update firmware?
SMOK does release firmware updates every now and then but these seldom change the look and feel of the UX (user experience) or how the mod’s menus and settings function. Normally, the firmware just adds more power and fixes known bugs. PLEASE NOTE: this guide is designed for newbie vapers.