Screw the Saionara or Divine Crossing v3 Atomizer onto the 510 threaded connector on the iStick Pico. Make sure you have a coil installed. The Atomizer and Coil that you are using will determine which Vaping Mode and Power Level you need to be using to ensure the best vaping experience.
Full Answer
How do I set up my istick Pico atomizer?
iStick Pico - Atomizer Setup 1 Step One. Gather your iStick Pico, Atomizer and 18650 Battery. ... 2 Step Two. Screw off the battery cap, put one high-drain 18650 Battery into the iStick Pico with the positive end facing down, then screw the battery cap back on. 3 Step Three. ... 4 Step Four. ... 5 Temperature Control. ...
What makes the istick Pico so special?
Powered by single interchangeable 18650 cell, the iStick Pico also provides you with 75W maximum output and switchable VW/Bypass/TC-Ni/TC-Ti/TCR modes. With a compact size, you can hold the kit in the palm, much more convenient for usage and portability.
How do I power on/off istick Pico 25?
Power on/off: screw off the battery cap, put one high-rate 18650 battery (positive side down and negative side up) into iStick Pico 25 and finally screw the battery cap on. The device can be powered on/off by pressing the fire button 5 times.
What kind of battery do I need for my istick Pico?
You’ll need a high-amperage 18650 battery for your new iStick Pico! We recommend a Samsung 25R, but if you choose to pick out a different battery, you’ll want to be sure it has a flat top and not a button top so that it fits correctly.
How do I change the coil on my Eleaf iStick Pico?
0:583:16Tank stuck on istick pico fix - melo 3 atomizer - Change coils - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell you screw this off this makes it. So much easier to get this off because you get a grip. And.MoreWell you screw this off this makes it. So much easier to get this off because you get a grip. And. Once you screw that off. Here is your coil guys. So the cones release to get off just twist.
How do I setup my iStick Pico?
Simply remove the battery cap and pop your new battery into the iStick Pico with the positive (less exposed) terminal facing down into the device, and the negative end (more exposed) pointing out towards you! Screw on the battery cap and now you can power on the device by pressing the fire button 5 times.
What coil does the iStick Pico use?
Like its bigger brothers in the Melo line, however, it uses a full-sized factory coil head. Two heads are included in the Kit, both vertical Kanthal coils, in 0.3 ohm and 0.5 ohm resistances.
How do I refill my Eleaf iStick vape?
2:023:20Eleaf iStick Power 2 Kit Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then take some of your favorite e-liquid. And begin filling by lifting the rubber seal locatedMoreAnd then take some of your favorite e-liquid. And begin filling by lifting the rubber seal located at the bottom of the tank after filling insert the pod back into the base and attach to the device.
How do I use an iStick?
iStick 30W is the one you deserve to own. Press the square button for five times to turn on the battery, and then long press the square button to get a puff. Loosen the square button to stop puff. Switch the VV/VW mode: Press the square button for three times to switch the VV/VW mode when the battery is turned on.
What is the price of iStick Pico?
Eleaf iStick Pico Plus Kit 75W Price $46.99 Online Sale | Vapesourcing.
How do you clean a burnt coil?
How to clean your CoilLet your coil soak in ethanol, vinegar, or cheap vodka for at least a couple of hours.Place it under the tap and rinse.Rinse once more with some distilled water.Blow air on the open side of your coil to force water to the wicking holes.Set it aside until all water has evaporated.
Why does my iStick Pico says no atomizer?
Replace Faulty Atomizer Coils Sometimes, the “no atomizer” or “check atomizer” error comes down to a faulty coil. Even with the most thorough inspection process, a dud coil can slip through. Alternatively, something in the coil may simply break down over time as you use it.
What is the best wattage for a 0.3 Ohm coil?
The sweet spot for getting a balance of vapour and flavour is around 0.3ohms. Depending on your coil choice you'll want to up the wattage from anywhere between 50 and 100 watts.
How do you load a vape?
2:173:37Beginner Vaper Tutorial: How to Fill a Vape Tank - ecsupplyinc.comYouTubeStart of suggested clipEnd of suggested clipHold the tank on its side slightly to let the juice slide. Down the juice slides right in. Like soMoreHold the tank on its side slightly to let the juice slide. Down the juice slides right in. Like so once you've filled your tank to their desired.
How do you fill a vape tank for the first time?
0:102:03How to Fill Vape Tanks - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply twist the top insert. The tip of your liquor bottle into the hole and squeeze.MoreSimply twist the top insert. The tip of your liquor bottle into the hole and squeeze.
How do I open my vape tank?
How to Refill a Vape TankTo refill your top-fill tank, start by removing it from the body of your e-cig mod.Unscrew the base and carefully remove the coil. ... Next, unscrew the top of the tank to add your e-liquid. ... Reassemble your tank and screw all the pieces back together tightly.More items...•
How many watts does Eleaf iStick Pico have?
It is a very compact and innovative device. It is powered by a single 18650 battery that is interchangeable. The maximum output of this one is up to 75 watts. Moreover, it features a top e-liquid filling design, detachable design, and hidden airflow control.
How to flip the display on a Pico?
To do that, you will need to press both the up and down buttons at the same time while the unit is turned off. Now, turn on the device, and you will see that the display has flipped 180-degree.
What is the ohm on a pico?
Many users have a hard time understanding the ohm on the iStick Pico. Generally, Ohm is the SI unit of electrical resistance. In simple terms, if the resistance or Ohm is lower, then the faster the electricity will flow through the coil.
How many things do you need to change to vape?
First of all, we will share a basic adjustment tip that might be enough to get a good vaping experience. Here, you will need to change 3 things : wattage, airflow, and the flavor filter.
Can you use multiple coils with iStick Pico?
You can use several types of coils with the iStick Pico. Interestingly, the device also comes with multiple vaping modes customized according to the coil you are using. For instance…
Is a coil hotter than a mod?
As a result, the coil will also be hotter as well. Then it will also produce more vapor, which would be very warmer than usual. Depending on the coil you use, it will have a different Ohm. But if you are using a regulated mod, then you should not worry about ohm very much.
Can you use coils with Pico?
You know that various types of coils can be used with the iStick Pico. Interestingly, most of the coils come with a recommended wattage setting. That way, you can set the wattage accurately depending on the coil settings. For instance…
How big is the iStick Pico 25?
The iStick Pico 25 ingeniously packs a big 0.91-inch screen that offers a concise and clear interface, 2A quick charge capability and upgradeable firmware with preheat function in a compact, stylish yet powerful package. Powered by single 18650 battery, the iStick Pico 25 is capable of outputting a maximum power of 85W and can handle various tanks up to 25mm diameter. The ELLO atomizer that features the HW coil for ultimate flavor and retractable top for easy filling pairs with the iStick Pico 25 perfectly in terms of both appearance and performance.
Why lock the resistance when the coil is at room temperature?
1.Please lock the resistance when the coil is at room temperature so that the device can display the correct “base resistance”.
How to increase wattage on a TC-Ni?
in TC-Ni/TC-Ti/TC-SS/TCR (M1,M2,M3) mode, the output wattage can be adjusted from 1W to 85W. Press the fire button 4 times in quick succession to enter the wattage setting menu and press “+” or “-” button to increase or decrease the wattage level. Keep pressing “+” or “-” button without looseness to rapidly increase or decrease the wattage level.
How to change TCR on a spherical coil?
1. Press the fire button repeatedly to choose among M1, M2 and M3 modes; 2. Press the “+” or “-” button to increase or decrease the TCR value according to the material of the coil you use; 3. Keep pressing the fire button or stay in the interface for about 10 seconds to confirm your setting.
How to adjust temperature on TC-Ni?
in TC-Ni/TC-Ti/TC-SS/TCR (M1,M2,M3) mode, temperature can be adjusted from 100-315℃ or 220-600℉ by pressing “+” or “-” button, “+” button to increase and “-” button to decrease. Each press of the “+” or “-” button will increase or decrease the temperature setting by 5℃ or 10℉. Keep pressing “+” or “-” button without looseness can rapidly increase or decrease temperature setting.
What does it mean when a vape is working with a weak battery?
in all vaping modes, when the device is working with an atomizer and the voltage of the battery drops below 2.9V, the screen will display “Weak Battery”. Meanwhile, the output power will be reduced accordingly.
How to switch between stealth and stealth off?
press the fire button and “-” button simultaneously when the device is powered on to switch between Stealth On and Stealth Off mode. In Stealth On mode, you can vape with the OLED screen off and you can press the fire button once to see current setting.
How to see your iStick Pico mode?
You can see your current mode by pressing the fire button 3 times quickly while the device is on and swap between the modes by pressing the up or down buttons to scroll through and then press the fire button to confirm your mode. The mode options are VW, Bypass, TC-Ni, TC-Ti, TC-SS, TCR-M1, TCR-M2, and TCR-M3. The M1, M2 and M3 modes are user-adjustable temperature control profiles, which you can set up to fit the coil you’re using!
How to unlock resistance on Pico?
In this mode you can lock and unlock your resistance when the Pico is on by pressing the fire button and up button at the same time for a couple of seconds. This will lock or unlock the atomizer base resistance.
How to change wattage on Eleaf Pico?
You can adjust your wattage in this mode from 1w to 75w by pressing the fire button 4 times to enter the menu, then using the up and down buttons to select your wattage level. You may also adjust your temperature from 200 degrees Fahrenheit to 600 degrees Fahrenheit by using the up and down buttons to move in ten-degree increments. If you hold either the up and down button, you can scroll through these temperatures more quickly. In this mode you can lock and unlock your resistance when the Pico is on by pressing the fire button and up button at the same time for a couple of seconds. This will lock or unlock the atomizer base resistance. If your resistance is locked, a lock sign will be displayed and an ohm symbol will be displayed when it is unlocked. You’ll want to lock the resistance when your coil is at room temperature for the best results. If you take your coil out and replace it or place a new one, the Eleaf Pico may maintain the same base resistance even if the coil resistance has increased from a rise in temperature. When you take your coil out in unlock mode and then replace it you may see a message saying “New coil up, same down” since coil resistance can increase within a certain range. If you’re using the same coil, you’ll want to press the down button or press the up button if it’s a new coil. Always unlock the resistance if you’re changing an atomizer or swapping a coil out for one of a different resistance. If you use a common coil or a coil with a resistance above 1.5 ohm in this mode by accident, your iStick Pico will switch back to VW mode automatically.
What is a Pico mod?
The Eleaf iStick Pico is a box mod with 510 threading and a wattage range from 1 to 75W for compatibility with nearly every 510 attachment. It has temperature control modes for nichrome, titanium and stainless steel heating elements with a range of 200-600 degrees Fahrenheit. Temperature information, battery life, resistance and wattage are all displayed on the Pico's crisp OLED screen along with other alerts. The Pico's body is built from corrosion resistant aluminum-zinc alloy and stainless steel to be durable and long lasting. The Pico is powered by a single 18650 battery and charges through standard micro-USB for convenience. Firmware upgrades are also available through Eleaf's website and add additional settings and allow changes to be made to the logo and display layout. We suggest pairing it with a Saionara Vaporizer or the Saionara Top Airflow Vaporizer for some awesome clouds and great flavor!
What is the TCR of a nickel coil?
TCR values are dependent on the coils you use. Nickel coils have a range of 600-700. Titanium coils have a range of 300-400. A nickel and iron alloy will have a range of 300-400 and a Stainless Steel 303, 304, 316, or 317 coil will have a range of 80-200.
How long does it take for a Pico to shut off?
The Pico is built to protect your atomizer and will shut off output if a vaping time is longer than ten seconds. It will also display an alert on the screen to let you know! For Saionara atomizers, shorter button pulses will provide the tastiest clouds in our experience!
How many batteries does a Pico have?
The Pico is powered by a single 18650 battery and charges through standard micro-USB for convenience. Firmware upgrades are also available through Eleaf's website and add additional settings and allow changes to be made to the logo and display layout.
What battery is needed for iStick Pico?
Gather your iStick Pico, Atomizer and 18650 Battery.
How to use iStick v3?
If you are using the Divine Crossing v3 Atomizer, y ou will need to put the iStick into Nickel Temperature Control Mode. Press the Fire button 3 times in quick succession , the iStick will show the current mode. Press the Up or Down button until Temperature Ni is displayed, then press the Fire button. If you are asked "New Coil Up, Same Down", press Up.
What cell is used for a TC-Ni atomizer?
Please make sure you are using a proper high-drain 18650 cell. If you received your battery directly from MaxVapor, you received a Sony VTC5 or equivalent.
How to set iStick to 10.0W?
First, put your iStick into Wattage mode by pressing the Fire button 3 times in quick succession, the iStick will show the current mode. Press the Up or Down button until Wattage is displayed, then press the Fire button. Now use the Down button to set the wattage to around 10.0w.
How to melt concentrate in atomizer?
Place a rice-grain or larger sized piece of concentrate directly into the atomizer, the best place to load will depend on the type of coil you are using. Pulse the Fire button lightly to melt the concentrate onto your coil and replace your atomizer cap.
How to use iStick atomizer?
If you are using the Saionara Atomizer with the Black Ceramic / Stainless Steel coil, you will need to put the iStick into Stainless Steel Temperature Control Mode. Press the Fire button 3 times in quick succession, the iStick will show the current mode. Press the Up or Down button until Temperature SS is displayed, then press the Fire button. If you are asked "New Coil Up, Same Down", press Up.
How long to hold a fire button?
Most users report a 5-4-4 pattern works well, this means holding the button for approximately 5 seconds, letting go of the button for a half second, fire for 4 seconds, etc.
