Full Answer
How to Prime a vape coil?
May 12, 2020 · To prime your vape coil before you start vaping, you’ll need to follow a few simple steps: Step 1: When you’ve taken your atomizer coil out of its packaging, locate the exposed cotton wick on the side. There are... Step 2: Choose a vape juice from one of your e-liquids and place a few drops on one ...
How to Prime refillable vape pods?
May 28, 2019 · How do I prime my coils? Priming your coils is easy. You just have to follow some easy steps. These steps are so easy that even if you are new to vaping you shouldn’t have any problem following them. Attach a new coil; Saturate your wicking material with e-juice; Take some dry hits; Break-in your coils; Attach a new coil
How do I use the Cool Fire IV?
Drip a couple of drops of e-liquid on the wicking holes and inside the coil head. Reassemble the vape tank and fill it with your choice of vape juice. Screw the tank on your vaping device and set it aside for at least 10 minutes. After the 10 minutes, inhale on the drip tip of the tank without firing.
What do I need to Prime my coil?
Feb 15, 2018 · Priming center of coil. Once your coil is well primed and saturated the next step is to fully install your coil into your tank, and take a couple of dry pulls. Dry pulls are when you take pulls, but with your device off and your airflow open. Take a …
Why is my cool fire IV not working?
Ensure the manual switch is on. (This is located on the base of the device). If the CoolFire is charging, try removing the charger and then replacing it. Try flipping the manual switch to off and then back on again.
How do you use Cool Fire IV Plus?
Press the button “ ” to lock the set wattage and activate the Cool Fire IV Plus. Press and hold the “ ” power button & "-" button together for 1 second to enter variable wattage mode. When the Cool Fire IV Plus is in variable voltage mode press and hold the "+" or "-" button and the set voltage will flash.
What is cool fire IV?
The Innokin CoolFire IV by Aquavape is a compact vaporizer from Innokin. With 40W of vaping power, it has a full range of tank resistances and a long lasting: 2000mAh hour battery. It is easy to use and vapes perfectly with the Innokin iSub tanks.
How do you change a cool fire IV coil?
0:203:20How to change a coil Innokin iSub B - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you can see you've got two prints either side that's where the coil needs to nest. Pull the coilMoreIf you can see you've got two prints either side that's where the coil needs to nest. Pull the coil out oh I like that and you've got access to your coil. If. This is a new coil.
How do I change my cool fire IV TC100?
When the CoolFireIV TC100 is in variable wattage mode press and hold the “+” or “-” button and the set wattage will flash. Release the button and press the “+” or “-” button again to increase or decrease the wattage. The CoolFireIV TC100 wattage can be adjusted from 6.0 to 100 watts in .
How do I change my cool fire Ultra to Watts?
0:502:25Innokin Coolfire Ultra Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour up or down your hold in either the up or down for a second until it flashes. And then you canMoreYour up or down your hold in either the up or down for a second until it flashes. And then you can scroll and adjust your wattage.
What tanks fit the cool fire IV?
Compatibility. The CoolFire IV vapes perfectly with the Innokin iSub Apex & iSub-G Sub Ohm tanks.
How do you fill an iSub tank?
2:373:41How To: Prime And Fill The Innokin iSub B Tank | Vaporleaf - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you don't want to get juice in here it will just flood your coil. And it won't be a pleasantMoreSo you don't want to get juice in here it will just flood your coil. And it won't be a pleasant experience. So just put your tip. Right in between the metal and the glass. And fill her up to the top.
How do you prime a vape coil?
0:451:52Priming a vape coil in 2 minutes - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet your either quid. And add a drop onto each of the liquid inlet holes add a few drops onto theMoreGet your either quid. And add a drop onto each of the liquid inlet holes add a few drops onto the wicking material down the middle hole put your vape coil in your tank fill your tank with the liquid.
How do you prime a innokin coil?
0:062:24How to prime/switch coils/fill the INNOKIN T28 II TANK - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust like so put it to the side as you can see just grab the end of your thread. And pull your coilMoreJust like so put it to the side as you can see just grab the end of your thread. And pull your coil out just like so.
How do you prime an innokin Z coil?
Prime your new coils Before you install the new coil in your tank or device, place 3-4 drops of your chosen e-liquid into the centre of the coil, directly onto the wicking material. Once you've done that, install the coil, fill your tank and wait for 5-10 minutes.Jun 4, 2021
How to break in vape coils?
Metal – like your coils – expands when heated and contracts when cooled. To break in your coils, start vaping using low wattage. You need to use a wattage that is lower than what you’re used to. Take a few hits and then gradually increase the wattage. Simply repeat the process until you reach your normal vaping wattage. When you have new coils, it is also important to take short hits during the first few times. This is a way of preventing the coils from getting too hot during break-in.
How long to leave a refillable pod?
Most refillable pods don’t have any e-juice in them upon purchase. Just fill the pod with e-juice. Leave the pod for around 10 to 15 minutes so it can properly saturate.
How to prime a vape coil?
How to prime a new coil for tanks: 1 Grab the fresh coil out of the box 2 Drip a couple of drops of e-liquid on the wicking holes and inside the coil head 3 Reassemble the vape tank and fill it with your choice of vape juice 4 Screw the tank on your vaping device and set it aside for at least 10 minutes 5 After the 10 minutes, inhale on the drip tip of the tank without firing 6 Adjust the wattage on your vape mod to the lowest recommended wattage resistance then hold on the fire button slowly and inhale 7 Gradually increase your wattage setting until you find your optimal range
Why is it important to take time to prep and prime your new vape coil?
It's important to take time to prep and prime your new vape coil to make sure that you are getting the most out of it and not burning it straight out of the box. Learn more about the reasons why your coils burn out to ensure you never lose a coil again!
How to increase wattage of vape mod?
Adjust the wattage on your vape mod to the lowest recommended wattage resistance then hold on the fire button slowly and inhale. Gradually increase your wattage setting until you find your optimal range. Once coil life is done then throw the old coil away and repeat this process again!
Why does my vape get burnt?
One reason this happens is if the coil is not primed properly and it is dry . When the vape device is fired and used at a high wattage it will heat up dry cotton and gives the vaper a burnt or dry hit.
How long to inhale e-liquid?
Screw the tank on your vaping device and set it aside for at least 10 minutes. After the 10 minutes, inhale on the drip tip of the tank without firing.
Can you quit smoking with an e-cigarette?
E-cigarettes have helped many people quit smoking. Most e-cigarette devices are easy to use and are beginner-friendly, but technical issues can still happen! All tank users and even rebuildable users have experienced a burnt taste after installing a brand new coil. In order to avoid a burnt vape, make sure the atomizer coils is primed correctly!
How many watts does a cool fire IV vape last?
Whilst many find the Cool Fire IV comfortable to hold due to it’s shape, others find it a bit awkward to hold. Battery won’t last the whole day if you vape at 40 watts. It’s a bit fiddly to change the wattage / voltage – but once you’ve done it once, it remembers your last settings.
How to switch to wattage mode on a Cool Fire IV?
To switch to wattage mode hold the power button and the plus button together. Similarly, to switch to voltage mode hold the power button and the minus button together.
How to tell if my Fire 4 is low on power?
The Cool Fire 4 has multiple battery indicators to let you know when the device is running low on power. The most obvious indicator is the battery icon on the OLED display, but you can also see the voltage remaining by holding down the plus and minus buttons simultaneously.
How long do you have to charge a cool fire?
Before using the Cool Fire you must charge the battery for at least 4 hours (ignoring the charge indicator for the initial charge). In the box you’ll find a Micro USB charger (DC 5V/1A) that you can use to charge your new device from a computer, or using a compatible plug adaptor.
What is the Innokin box mod made of?
It’s a high quality build made from lightweight aluminium that is formed to fit your hand comfortably. The brushed aluminium finish and range of colours makes the device very aesthetically pleasing.
How much is the Innokin Cool Fire 4?
The Innokin Cool Fire IV (available for £39.99) is the newest box mod on ECigaretteDirect, and the latest model in the popular Cool Fire series. In this post you’ll find an overview and tutorial with everything you need to know to use it.
Can you vape while charging a cool fire?
If, like me, you’re always forgetting to charge your battery until the last minute, you can also vape while it charges using its passthrough capability. By locating the micro USB port on the side of the device, it allows you to stand the Cool Fire upright while it’s charging.
How to check atomizer resistance?
With an atomizer attached, hold both the “+” and “-” buttons simultaneously and the secondary screen will display the precise resistance of the attached atomizer, the battery voltage and the number of puffs since the device was last turned off.
Can you charge a battery that has been dropped?
Never charge a battery that has been damaged or dropped.Never plug a charger into a non-approved mains power transformer.Donot overcharge. Remove the battery from the charger when charging is complete.Never leave a charging battery unattended.Only use the included high quality charging cable.
How many watts does an Innokin Coolfire IV 4 have?
Innokin Coolfire IV 4 is an advanced variable voltage/wattage device that can fire up to 40W and 7.5 V. It features 2000mAh capacity, safety protection, OLED screen, 510 spring loaded and ability to handle resistance as low as 0.3ohm and safety protections.
What is the wattage range of a Coolfire 4?
The variable wattage range for the Coolfire 4 are between 6W to 40W with the adjustable of 0.5W increments, which is great and compatible with most of the sub-ohm atomizers in the market today.
Can you leave batteries unattended?
Always charge batteries at the clean and fire-proof surface. Never leave charging batteries unattended. If you see that there are visible damages on the batteries, please do not use. Always keep, store and transport the rechargeable cells in a safe, non-conductive container in controlled environment.