- Clean all contacts on battery/mod, tank or pod.
- Remove and reinstall the coil (after cleaning)
- Try a new coil.
- Check the 510 pin and see if you can adjust it (mods/tanks)
- Try another tank on your mod.
- Try another mod with your tank.
- Adjust base of coil carefully if you can (mainly sub-Ohm coils)
How to fix check atomizer/No atomizer with a vape tank?
May 25, 2021 · To loosen it, you'll need to use a screwdriver to gently press down on the connector (since most of the connectors are spring-loaded, this should loosen it). This should fix the problem, but if not, it's time to check the coil. Check Your Coil Sometimes the reason you see the “No Atomizer” message is because there is a problem with the coil.
How do I fix the “No atomizer” message?
Dec 28, 2021 · How to Fix 'NO ATOMIZER' or 'CHECK ATOMIZER' Step One - Clean all contact points. Remove the tank (or pod, if you have one) from your computer and clean all threads... Step Two - Reseat the coil. Remove and replace the coil in your tank. Occasionally, this miraculously solves the problem. Step Three ...
What does ‘No atomizer’ mean on an e-cig?
Oct 07, 2020 · #noatomizermessage #noatomizer #vaping Jonny at Totally Wicked shows you how to fix a no atomizer message on your vape 0:00 How to fix a 'no atomizer' messag...
Is your vape mod not reading the coil properly?
Jan 31, 2018 · This fix works for most vape/mod combos. Thanks for watching Song is "Get here soon" by a good friend of mine, shotsofcolor. Check him out here - https://www...
What to do if cleaning contact points doesn't fix check atomizer error?
If cleaning the contact points doesn’t fix the check atomizer error on your pod vape, you’ll want to carefully examine the contact pins/plates on your pod vape and on your pod for damage.
What to do if your pod vape isn't firing?
If your pod vape isn’t firing, has a blinking LED and won’t fire, or says Check Atomizer or No Atomizer, you can follow a few of the same steps listed above for tanks: 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points.
Why won't my 510 mod work?
Simply put, if your mod can’t read your tank and coil resistance properly, it won’t be able to deliver power and therefore won’t work.
How to clean a tank after taking apart?
Once you’ve taken apart your tank, unscrew your coil from the base of the tank. Now, you’ll want to clean the bottom of the coil where it screws into the tank and makes contact. You’ll also want to clean your tanks contact point with the mod as well. Once done, reseat your coil, and reassemble your tank.
How to clean a pod from a vape?
Also check inside your vape where the pod attaches to it. If you see any ejuice or dirt, clean it out with a paper towel then reinsert the pod and try again.
What causes a check atomizer short?
Loose pieces of metal on the build deck will cause your mod to display “Check Atomizer” or “Atomizer Short”. Even very small pieces or trimmings of wire can cause a short or a check atomizer error on an RDA/RTA/RDTA. First, inspect the build deck closely for loose pieces of wire or other foreign objects.
Why is my mod reading the new tank correctly?
If your mod is reading the new tank correctly, it could be a problem with the coil on your other tank. You might also want to clean the contact points on the tank that was giving you the error. If your mod is still reading “check atomizer” with a new tank, it’s probably a problem with your mod.
How to get vape juice out of a tank?
Take the base of your tank off. Take care if it is full of fluid and make sure you can remove the base without the tank leaking. If not decant the vape juice out of the tank first. Now check that your coil is screwed into the base of the tank correctly.
What does it mean when an e-cigarette says no atomizer?
An e-cig that says ‘no atomizer’ or ‘check atomizer’ is a message that no vaper wants to see. A source of frustration because this message flashing up on your vape mod most probably means that you cannot vape.
What does it mean when your tank is sat flush with a rubber o-ring?
If you have over tightened your tank onto your mod, it can push the metal plate from the 510 connection up into the tank. This usually means that it is sat flush with a rubber o-ring. If this is the case then it won’t make a full connection to your e-cig.
How to get a tank to pop back into the correct position?
Take your tank off your mod and turn it off, or remove the battery. Then take something small, like a small screwdriver and very gently press down on the pin. You should feel the spring underneath and this can get it to pop back into the correct position. Try attaching your tank again and see if the message has gone.
Can a mod make a complete connection to a vape tank?
Over time the connection on your e-cig can gather dust, dirt and e-liquid. If this is the case and your mod can’t make a complete connection to your vape tank, then this message will display. Remove your tank from your e-cig and have a look at the threads and metal plate to make sure there are no larger pieces of debris there.
Why do vapers forget atomizer error messages?
They were added by the manufacturer to protect you from faulty atomizers, and to prevent firing mishaps that can cause damage or injury.
Why does my vape pen leak?
There’s vape juice in your vape pen – leaky atomizers are damaged atomizers. When juice seeps into your circuitry, it can damage it and cause it to show error messages when there’s actually nothing wrong with the atomizer.
Why does my mod say no atomizer?
However, once you put your top cap on, the sides are touching the coil (usually because it’s either too large or protrudes to one side too much), and that causes your mod to show you a “no atomizer” or “short atomizer” error message.
What is 510 connection?
In short, a tank’s 510 connection is that little bit with threads that protrudes and is screwed onto a vaporizer. It has a little pin that’s movable and that carries the positive charge from the vaporizer to the atomizer. It’s that little pin that can go haywire sometimes, and fail to connect.
What does it mean when your chipset says no atomizer?
When your chipset is responsible for an “atomizer short “or a “no atomizer” error message, it means that it’s preventing firing on the basest of levels. There’s nothing here that you can fiddle with or adjust to fix this.
No Atomizer
Hi there... I'm new to Yocan UNI Pro mods and have no idea why I am consistently getting a No Atomizer warning ( there is one in there). My Uni Pro is only a week old, fully charged, and I'm using the magnet adapter that came with the device. Sometimes it works, most of the time it doesn't.
Re: No Atomizer
Hi @LaurenMaurer Thanks for your thread. Please try to reload the oil cartridge, or clean the connection points of magnetic adapter. By the way, you also can refer to this page to fix this issue: https://www.yocantech.com/help-center#UNI Any further questions, please let me know.
Re: No Atomizer
I am just gonna bump this, as I have exactly the same problems as the original poster. Bought a unipro and started having No Atomizer issues with both .5 and 1.0ml amigo carts right away. Have tried cleaning the connections, tight & loose, different carts, all to no avail. So if anybody has any tips before I give up, be much appreciated.
Re: No Atomizer
I am just gonna bump this, as I have exactly the same problems as the original poster. Bought a unipro and started having No Atomizer issues with both .5 and 1.0ml amigo carts right away. Have tried cleaning the connections, tight & loose, different carts, all to no avail. So if anybody has any tips before I give up, be much appreciated.
