Spray a bit between the mod and tank to help clean off the dried ejuice that usually causes your tank to get stuck. Leave it on for a few minutes, dry it off with a clean piece of cloth, then try the above methods again. It just might work this time around.
Full Answer
What to do when your vape mod stops working?
This is particularly useful if your vape mod stops working suddenly. Knowing exactly how to disassemble your device and thoroughly examine each part will give you the information on what parts need fixing and on what stopped working. One of the most difficult parts of a mod to take apart is the firing button.
Can You disassemble and reassemble your vape mods without hiccups?
Fortunately, there are some good tips and ideas that will help you properly disassemble and reassemble your vape mods with no hiccups. This is particularly useful if your vape mod stops working suddenly.
Should I replace my vape battery if it cracks?
Cracks in batteries are not a good sign, as they can quickly become larger and start to incur on the actual lithium ion segment of the battery. At this point, the battery must be replaced as it is potentially hazardous. By regularly disassembling your vape and examining your battery, you'll be able to tell whether your battery is a hazard or not.
What is better than a fixed vape mod?
Before we begin, it’s important to note that the only thing better than a fixed vape mod is one that doesn’t break in the first place. The new generation of vape mods is headlined by devices like the Geekvape Aegis.
How do I remove scratches from my vape screen?
Apply a liberal amount of toothpaste to scratched surface. Wipe any excess away and allow the toothpaste to dry in the cracks/scratches. Be sure to use a paste-based toothpaste and not a gel toothpaste. Use a soft cloth to polish the surface when the toothpaste has dried to remove the scratches.
Can scratched plastic be restored?
Apply a mild abrasive, such as toothpaste, furniture polish, baking soda or plastic polish to the scratch. Try our VuPlex Plastic Cleaning Kit which will also give your surface a gloss finish. Wipe a clean cloth over the paste you have added in a circular motion.
Can you fix scratches on resin?
Most scratches can be sanded right out rather quickly using a variety of fine-grit sandpaper. *Directions are specific to white resin finishes only. Use warm water to remove dirt and dust from the surface. Use #800 grit sandpaper and rub in small, circular motions until the scratch is gone.
Can you buff out deep scratches on plastic?
Baking soda is a gentle mineral abrasive that will buff away scratches on plastic. Combine two parts baking soda to one part water to create a thick paste. Dip a cotton cloth in the paste and apply it to the scratched area. Work in a circular motion to buff away the scratch.
Does WD 40 remove scratches from plastic?
Does WD 40 remove scratches from plastic? WD 40 is a water-displacing oil that is used to lubricate tools and remove water from metal surfaces. It does not remove scratches from plastic.
Does toothpaste remove scratches from plastic?
Polishing plastic with toothpaste Using toothpaste is really effective to remove small surface scratches from soft plastics on small household items like frames or storage boxes. You'll want to use a non-gel paste and if you can find one with baking soda in it, that's an added bonus.
How do you get surface scratches out of resin?
0:5510:26How to fix flaws in resin - resin for beginners - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I've already gone ahead and done a little bit of work on it and basically I've used sand papersMoreSo I've already gone ahead and done a little bit of work on it and basically I've used sand papers these are wet or dry sand papers. And I've got the first one here is a 220 generally the higher the
How do you touch up resin?
0:123:29Resin mistake we all can make and how to fix it! - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you've completely wiped your board of alcohol. Then you just need to get some sandpaper. And goMoreOnce you've completely wiped your board of alcohol. Then you just need to get some sandpaper. And go over the entire surface. Just giving it a little bit of tooth.
Can resin be repaired?
Most resin statues can be quickly and easily repaired at minimal cost. The process of repairing a resin statue is simple; you should be able to complete all but the largest repairs in less than an hour.
Can you buff plastic?
For hard plastics like acrylic and polycarbonate, a buffing wheel is a good option. Turn the wheel on, and then hold the plastic up to the wheel where the scratch is. After a few minutes, the scratch should be gone. It will also work to buff up soft plastics, like motorcycle trim.
How do you get deep scratches out of black plastic?
How to Remove Scratches From Black PlasticApply a dab of the plastic scratch remover or metal polish to a soft cloth.Buff the scratched surface with the product, using back-and-forth and circular motions. Use gentle to medium pressure. ... Repeat the process, if necessary, to remove any remaining scratches.
How do you smooth out plastic?
3:035:33How to Polish and Repair Scratched Plastic - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe piece then use a sander with 320 grit sandpaper to remove all the machine marks. This willMoreThe piece then use a sander with 320 grit sandpaper to remove all the machine marks. This will produce a frosted. But smooth edge flame polish this and you will have a showpiece finish for the
First Steps When Troubleshooting Any Vape Mod
If you’re an experienced vaper, you can probably skip this section of our troubleshooting guide. If you’re new to vaping, though, you should know that every vaping device with a fire button has a built-in locking function to prevent the device from firing when you don’t want it to – for instance, while you’re carrying the device in your pocket.
How to Troubleshoot the Battery in Your Vape Mod
Let’s suppose that your vape mod doesn’t respond at all when you try to use it. You’ve tried connecting the device to a power source, and it doesn’t seem to be charging normally. How can you find the cause of the problem?
How to Troubleshoot a Vape Mod That Leaks or Gurgles
The next two problems that we’re going to discuss in this guide are problems that don’t indicate a hardware failure but do affect the quality if your vaping experience. The first of those is when your tank or pod gurgles or leaks.
How to Troubleshoot a Vape Mod That Tastes Burnt
The final common problem that affects the experience of using a vape mod is an unpleasant burned flavor that manifests itself when you vape. Vaping is supposed to taste good.
How to tell if vape is burning?
The easiest way to identify why your vape tastes burned is by looking at the atomizer coil. If you look through the top of the coil, you’ll see the coil’s mesh or wire heating surface. If the heating surface is dark brown or black, you’re dealing with a problem that relates to e-liquid residue.
Why does my vape taste burnt?
If the heating surface of your coil is dark brown or black when you remove the coil from your tank, the reason why your vape tastes burned is because you’re using an e-liquid heavily sweetened with sucralose.
How long should I puff a vape?
Lastly, remember that your coil’s suggested wattage range is based on a puff length of about two seconds.
Why does my vape tank leak?
The most common reason why a vape tank leaks is because it isn’t assembled correctly. A vape tank uses a complex arrangement of silicone o-rings and metal threads to keep the e-liquid where it’s supposed to be – and if anything is out of place, the e-liquid will begin to seep out of the airflow vents at the bottom of the tank.
How many gaskets are needed for a vape tank?
A vape tank generally includes at least one set of replacement gaskets. Reassemble the tank slowly, making sure that none of the threads are misaligned. The threads on a vape tank are thin enough that it’s not too difficult to force the parts together even if the threads are crossed.
How to tear apart a vape atomizer?
To tear apart the vape tank and vape atomizer, you'll have to attempt to unscrew the vape tank. Usually, there need to be a few other steps included to fully unscrew the vape tank. First, after unscrewing as much as possible, of course - make sure there's no e-liquid left in the tank.
What is the battery of a vape?
Of course, the vape battery is an absolutely critical component of your device. This is what gives your device the power to be able to heat up e-liquid to turn into vapor. This is what allows your vaping sessions ...
Can you clean a vape mod?
Even though vape mods are designed with customizability in mind, cleaning them can still be a chore. From the many already built-in parts to the extra technology you add, the little nooks and crannies of your box mod that you need to take care of add up quickly. Fortunately, there are some good tips and ideas that will help you properly disassemble ...
How to unstuck a tank?
If you can’t get a piece of cloth to grip your tank properly, and you can’t source a pair of rubber gloves, rubber bands can work. Get a piece of rubber band, wrap it around your tank tightly and securely, then twist it open bare handed. The added grip is usually enough to unstuck your tank.
How to prevent a stuck tank?
To prevent stuck tanks, make sure you don’t screw it on too tight, and you clean your mod and tank at least every week. Clean the part in between the mod and tank to be sure no e-juice gets stuck and dried. After all, an ounce of prevention is worth 10mls of cure. OZ Vapour Team.
Beamslider Vaping Master Verified Member ECF Veteran
Don't have the blade. But the Geekvape Aegis I have came with a peel off plastic protector on it. Did you check to see if there was one on the blade. Maybe that is what is scratched up. But the screens all scratch over time
Izan Vaping Master ECF Veteran
Thank you for your quick response. I've tried scratching from the edges but i really can't get it off (if there actually is a protector). I'm aware that every screen scratches over time, but i litterally just unboxed it.
Toots Senior Member ECF Veteran
Hi guys, i just received my new Geekvape Blade mod and it's working absolutely fine and i love it. But i immediately noticed that the screen is all scratched up right out of the box which would be fine if there was a screen protector on it, but i'm not sure if it has one. I've searched online but i can't find anything.
Radar2013 Super Member ECF Veteran
Just by the looks of the pics it loiks like a used or return that got mixed up with the new ones. My Aegis came with a peelable protector.... Might oughta get ahold of customer service.
untar Vaping Master
On your picture in the southeast of the middle there seems to be a deep nick at the border of the screen cover, kind of like a bear had a go at it before you. Even with a screen protector I wouldn't expect that to go away.
Baditude ECF Guru ECF Veteran
Hmm. I bought the Blade from ebay but it was sealed and definitely new. Everything works as it should, only the screen bothers me.
Baditude ECF Guru ECF Veteran
It was a private auction from a private seller so i doubt that to be honest.
