Can You disassemble and reassemble your vape mods without hiccups?
· Add some e-liquid to the pod and reassemble the device. If your disposable vape has a fiber-based filler material inside, you’ll need to remove the filler material from the device and re-saturate it with e-liquid. When the filler is wet again, …
What to do when your vape mod stops working?
· First, after unscrewing as much as possible, of course - make sure there's no e-liquid left in the tank. Next, run a tiny screwdriver through the airflow slots and tap around a bit to loosen up the seals. If the tank still isn't budging, then place the whole segment in the freezer to make the seal loosen even more.
How to unscrew a vape tank?
Start by removing the top cap of your Vape Mod. Add a comment Step 2 Unscrew RDA (rebuildable dripping atomizer) and take it off. Add a comment Step 3 Many Vape Mods are different, you might have to take out your battery in a different way than shown. At the bottom of the tube, unscrew the firing pin. Take the battery out of the Vape Mod.
Should I replace my vape battery if it cracks?
· Once you’re prepared to examine the device, try these steps: Replace your device’s batteries. Sometimes, a battery is just a bad egg, and can be sending power of its own accord. Try switching out your batteries to see if it fixes the issue. Check your chip and switch for burnout signs. A fried chip or switch is one of the most common causes ...
Disassemble and reassemble your vape box mods
Even though vape mods are designed with customizability in mind, cleaning them can still be a chore. From the many already built-in parts to the extra technology you add, the little nooks and crannies of your box mod that you need to take care of add up quickly.
Box mod firing button
One of the most difficult parts of a mod to take apart is the firing button. This button is usually made up of a few parts. There is the button itself, which needs to be taken off and wiped down. Below that, you'll have a spring, which can also be taken off and scrubbed.
The vape battery
Another important part to know how to properly remove and reattach to your vape device is the vape battery. Of course, the vape battery is an absolutely critical component of your device. This is what gives your device the power to be able to heat up e-liquid to turn into vapor.
The vape tank and atomizer
The third and definitely not final part that you should definitely know how to disassemble and reassemble is the vape tank and vape atomizer complex. You may already know how to do this if you change your coils often, but it can never hurt to have a reminder.
Introduction
This guide will teach you how to take apart your Vape Mod completely, analyze which parts need to be cleaned, and how to correctly clean them.
Step 1 How to clean and maintain your Vape Mod
Although maintenance for your Vape Mod shouldn't be dangerous, it can be messy. It is recommended to do this on top of a paper towel.
Step 3
Many Vape Mods are different, you might have to take out your battery in a different way than shown.
What is Auto Firing?
The term “auto firing” refers to a vaporizer that is firing, but without the user pressing the main fire or power button. The device is often being stored in a pocket, purse or drawer when it happens, not even within reach of an accidental button push.
Why is My Vape Auto Firing a Dangerous Issue?
You can probably guess that it’s not a good idea for your vaporizer to be firing outside of your control. Anytime a piece of machinery operates without your commands, there’s cause for concern. However, that is especially true for a vape device because it is designed to generate a significant level of heat.
How Can I Fix My Auto Firing Vape Device?
If you’re comfortable doing a bit of troubleshooting, you may be able to determine what is causing your device to auto fire, and possibly even make a few repairs to solve the issue. There are a few minor changes that could stop the auto firing and protect you from a potentially dangerous situation.