How to set up a vape?
How to set up a Vape. 1 Step 1 - Prepare your device. Remove your device from the box and place it on a flat surface in front of you. 2 Step 2 - Fill your tank or pod with e-liquid. 3 Step 3 - Prime your coil / pod. 4 Step 4 - Settings or no Settings? 5 Step 5 - Set the correct output power. More items
Where to buy the drag 2 vape?
Although the Drag 2 has gained popularity rather quickly and you can buy it nearly anywhere, we recommend you to shop at VaporAuthority.com, an online vapor shop that has gained the respect of the vaping community due to their incredible customer service and a large selection of the industry’s latest and greatest products.
How to adjust the wattage on a vape gun?
Once you’ve got the desired wattage set, press and hold the fire button until you reach the desired amount of vapor. How To Adjust The Wattage: While in the wattage or power mode, you can press up or down on the adjustment buttons located on the device’s control face.
How to turn on the drag 2 mod?
How To Turn On The Drag 2 Mod: To turn on the Drag 2, simply press the fire button 5 times consecutively. To turn the device off, repeat the process. How To Activate and Vape: When you first turn the device on, it will automatically default to its variable wattage mode.
How do I change my drag settings on Voopoo?
2:355:33DRAG 3 mod and settings by voopoo - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf we get the up and down bar and press them. Together. We can change the theme. So we've gone downMoreIf we get the up and down bar and press them. Together. We can change the theme. So we've gone down to the next one press the fire button.
How do I change the wattage on my drag vape?
To adjust wattage while in TC Mode, press fire button 4 times rapidly to activate wattage adjustment. You will see the “W” wattage icon flashing. The wattage can be adjusted from 5W to 80W.
How do I adjust my vape settings?
1:503:08How to setup your Mod Kit? - YouTubeYouTubeStart of suggested clipEnd of suggested clipHowever if you're using a suburb device a coil of 1.0 ohm and under you need a thicker liquid weMoreHowever if you're using a suburb device a coil of 1.0 ohm and under you need a thicker liquid we recommend a 70 30 ratio as the device is more powerful if you use 50 50 liquid in a sub-ohm.
How do I change the voltage on my Voopoo drag S?
Five clicks of the power button turn the device on and off. Three clicks of the fire button to change between “smart” and “RBA” mode on the X (the S allows you to swap between button press and auto-draw mode too). Press up or down to adjust the wattage.
How do you lock Watts on Voopoo drag?
5x clicking the fire button to turn the device off/on, Fire button + down clears the puff counter, Fire button + Up will put you in wattage lock, 3 clicks of the fire button will change you between Smart Wattage and RBA modes.
How do you unlock drag mod?
- Lock / Unlock = Press the Fire button and '+' (up) button simultaneously. - Mode Switching = Quickly press the fire button 3 times.
How do I adjust the heat on my vape pen?
Most vape pens with buttons require five clicks to turn them on, three clicks to change the heat setting, and five clicks to turn them back off. The button heats the chamber as you hold it down, so be sure to hold the button down as you're taking your hit.
How can I increase my vape flavor?
ContentsBest Wattage and Temperature Settings For Flavour.Reduce Your Airflow.Choose Your Coil Carefully.Wicking and Coil Materials Matters.Think About VG:PG Ratios.Below-Coil Airflow Boosts Flavour.Choose a Narrower-Bore Drip Tip.Keep Your Wicks, Coils and Tanks Clean.More items...
What temp and wattage should I vape at?
Many people agree that 420 degrees Fahrenheit or 216 degrees Celsius is the sweet spot. You get as much flavor as possible without feeling the warmth of the vapor. If you want to add even more flavor, try a temperature between 425 and 450 degrees Fahrenheit or 218 and 232 degrees Celsius.
How do I change my Voopoo too settings?
To adjust wattage while in TC Mode, press fire button 4 times rapidly to activate wattage adjustment. You will see the “W” wattage icon flashing. The wattage can be adjusted between a range from 5Wminimum to 80W.
How do I change settings in drag 3?
Drag 3 Button CombinationsPower On or Off: Press the fire button 5 times.Switch Modes: Press the fire button 3 times.Change UI: Hold both adjustment buttons to bring up the UI menu. ... Lock/Unlock All Buttons (Including the Fire Button): Hold the fire button and top adjustment button together.More items...•
What wattage should I vape at Drag s?
In my experience, this coil performs best at 40W and the flavor is actually better than the 0.15Ω coil. It's the perfect level of warmth and flavor. Unlocking the Drag S Pro into RBA mode lets you take this coil up to whatever wattage you like and I tested it out at 50W. It's a hot vape here but it still performs well.
What is Drag 2 Mod?
What’s fascinating about the Drag 2 Mod by VOOPOO, aside from its good looks, is the advanced GENE.FIT chip that’s integrated into the device. It provides a full range of features, like temp control, TCR adjustments, the new FIT mode, and a variable wattage mode that will allow you to reach up to 177W. To control the device to the fullest ability, there is a large firing button, two adjustment buttons, and an intuitive OLED display screen. Combine all of this with its protection suite and a micro-USB port that supports charging and future firmware upgrades, and you’ve got yourself one of the impressive devices on the market.
Why does Drag 2 say "Check Atomizer"?
That could be the result of a few things, such as your tank or atomizer not being attached to the device, it not making a solid connection, or an issue with your coil not making a connection. Most times when you see this prompt, it will be that your tank isn’t attached or not tightened enough to make a solid enough connection.
How tall is the Voopoo Drag 2 mod?
One of its latest releases is the VOOPOO Drag 2 Mod, a fascinating device that features a remarkable chassis. It stands just 88.3mm tall, 51mm wide, and only 26.5mm in depth. It’s constructed of a superior zinc alloy material, giving it incredible durability and strengthens its external shell for an increased lifespan. Enhancing its appearance, the Drag 2 Mod comes included with a visually striking resin inlay design that’s available in Island, Flame, Aurora, Scarlet, Fire Cloud, Puzzle, Dawn, and Ink finishes. Positioned on the backside of the device there is a magnetized battery door cover which is capable of housing dual 18650 batteries, giving you longer durations between charges.
How to enter function menu?
How To Enter Function Menu: To enter the function menu, press the up and down adjustment buttons simultaneously.
Why does Drag 2 turn off?
There could be a couple of reasons why your Drag 2 Mod would turn off, and two of them primarily being that there is a sleep mode that activates after the device is inactive for 30 seconds or your batteries have depleted too low.
How to activate a Vape?
How To Activate and Vape: When you first turn the device on, it will automatically default to its variable wattage mode. From there, you can adjust the wattage or rely on the automatically recommended wattage the device provides. Press and hold the fire button and your coil will vaporize the e-liquid.
How to install batteries in a mod?
How To Correctly Install The Batteries: Begin by turning the mod to its backside. On the back, there is a removable battery access door. Once you remove the access door, you will see two battery bays, each marked to indicate how to properly insert the batteries. If you aren’t sure of how to install the battery properly and need to learn more about battery safety, we recommend you do that before attempting to install the batteries.
How many watts does a Zelos vape have?
For Example: When using the Aspire Zelos Kit it ships with a 1.8ohm BVC coil. This coil type has a recommended wattage of 9-15watts. To use the device correctly you will set your device to output somewhere between 9-15w. Around halfway is a good place to start so you would set your device to 12w by using the arrow keys. This will make sure you don’t overpower or underpower the coil inside the tank.
How to try a vape out for the first time?
To try your new vape out for the first time; place your mouth on the drip tip/mouthpiece, begin to draw from the mouthpiece and/or hold down the fire button at the same time as you are drawing.
What are the different types of vapes?
There are 2 types of vapes; fixed powered devices and variable powered devices. This refers to the ability to adjust the power settings and fine-tune the vape experience. If you have a pod system its likely type 1, but read through both types below to make sure before proceeding.
What happens if you set your coil incorrectly?
If set incorrectly this can lead to the coil burning out and that bad taste we were talking about earlier. To know what settings you need for your device you can find this information in a few places; in the manual or on the packaging, on the coil itself or coil packaging, or online from the manufactures/retailer where you purchased your device from.
How long should I let my pod sit before using it?
This is an important step to get the optimum flavour and experience. Let your tank or pod sit for 5 minutes before you first use it.….yes I know you feel like you have waited long enough…but trust me it will pay off.
Why do you let your tank sit?
By letting your tank sit you are making sure the cotton is truly soaked with e-liquid to prevent a dry hit and potentially burning the coil. Prime your coil: A popular method for helping the e-liquid soak through is priming. This gives you extra reassurance that you won't get that nasty dry hit.
What does it mean when a device has no display screen?
Type 1) If your device has NO display screen and NO controls on the side to adjust the power output this means you have a fixed powered device - jump to Step 6. Type 2) If your device has a display screen and controls on the side to adjust the power this means you have a variable powered device - proceed to Step 5.
How to check if a drag mini mod is authentic?
To verify the authenticity of your Drag Mini mod, simply looking on the packaging that held your mod and you’ll see a sticker to check the authenticity. There’s a code on the sticker. There are two ways to find this code, which is by scratching the silver cover to reveal the code or slowly rotating the mark in the light. Once you find the code, visit VOOPOO’s Authenticity Query page and validate the product.
What is included in the Drag Mini 117W mod?
The Drag Mini Mod Includes: You’ll receive the Drag Mini 117W Mod, a USB cable, instructional manual, and a warranty card.
Why does my Drag Mini turn off?
The only other reasonable explanation of why your Drag Mini Mod would turn off is because the battery has depleted too far and needs to be recharged.
How big is the Voopoo Drag Mini Mod?
It stands just 81.5mm by 48.5mm by 25.5mm, offering a compact design that’s very comfortable. Aside from the immaculate appearance with its striking resin inlay design, which is available in Atrovirens, Rhodonite, Coral, Prussian Blue, Lava, Prussian, Purple, and Lime, along with an intuitive OLED display, the entire device is structurally sound. It’s constructed of a superior zinc alloy material, making it both durable and lightweight. There’s a three-button control face to make necessary adjustments, and a micro-USB port is equipped towards the bottom, which allows for both charging and future firmware upgrades.
Why does my drag mini say "check atomizer"?
This prompt typically means there is a connection issue of some sorts, which could be the result of the tank not being attached, the tank and the device’s connection between one another (not tightened down enough), or there could even be an issue with your coil not making a connection. If you need help, we have an article that will tell you how to fix a coil connection issue to solve the problem.
How to switch between modes on Voopoo Drag Mini?
How To Switch Between Modes: To switch between the different modes on the VOOPOO Drag Mini Mod, press the fire button 3 times to switch from Power Mode (VW), FIT Mode, or temperature control mode.
How to turn on Drag Mini?
How To Turn On The Drag Mini Mod: Press the fire button 5 times consecutively. To turn the device off, repeat the process.
What coils are used in power mode?
Pretty much all coils need to use with this mode, you can use Kanthal, stainless steel (SS), and nichrome ( nickel -chrome) coils. most of readily made coils are made out of Kanthal Wire, which is why power mode tends to be oh-so-popular among users of different expertise levels.
What is VT in heating?
Temperature Control, or as referred to sometimes as Variable Temperature (VT), is a very useful mode where you set the exact temperature threshold for heating your coils steadily. TC wires are limited to their own specific setting, as their individual heating properties vary. While using this mode, make sure that you use the correct mode for the wire of your coil.
What is bypass mode?
Bypass mode gives you the experience of raw power of your battery to heat your coils. Here you can build your coils at lower resistances than is normally accepted by power or temperature control mode, meaning that the power of the hit will be determined by the sheer state of you battery and the resistance of the atomizer.
What is power mode?
Power mode is very self explanatory. You can choose the level of wattage (amount of power per second) or voltage (the force of that power). This is used to set the optimal power for your device, as written on the coil you are using, to produce the right amount of cloud and flavor.
Can you dry burn nickel coils?
Nickel coils are known for their rapid ramp-up speed, but they consist a softer metal which can be annoying to work with sometimes, when you’re building. Nickel coils shouldn’t be dry burnt, as this can oxidize the metal and ruin your coils. In addition, nickel can sometimes cause a negative reaction in vapers who are allergic to the metal.
Do mods support coils?
Here it’s better to have basic understanding of coils, and it’s always advised to check your device carefully, because some mods support particular coils for TC mode, while others state clearly that they support more than one type, which you’ll find in the settings as TC-Ni, TC- Ti or TC ( NI, Ti ).
Is stainless steel wire safe?
Like nickel and titanium, it has an impressive instantaneous ramp up time, yet it’s safe if it was exposed to a dry burn and wouldn’t cause allergic reactions. Sta inless steel is especially popular because it can be used both in power and SS temperature control modes.
Community
Heya all you absolute legends. Just want to say thanks for all your advice. This is an amazing community to be apart of and ty 4 all your help 😁😁
Switched from Caliburn to GeekVape Aegis. Help Please?
Two years since i puffed my last combustible puff. Hope you are all doing well.
Some noob questions about regular coil builds
I‘m Vaping since 2-3 years but only got into mesh builds so far. But my curiosity got me and I went out and purchased some „geekvape 2 in 1 coils“ from Amazon and put those into my profile rdta, dual coil build.
