If you’re using a touchscreen SMOK mod, there will be a settings icon on the home screen which you can simply tap to access the mod’s settings. If you’re using a non-touch device, just click the fire key THREE times to enter the Settings Menu. Once inside Settings, you can move through the menus using the UP and DOWN keys on the mod.
Full Answer
How do I change the coil on my Smok mod?
Jan 08, 2017 · Simple The solution is to press the fire button so the screen comes on and then screw the tank off. Again press the fire button so the screen is on when you screw the tank back on again. So basically make sure that the screen is always on when you unscrew and rescrew the atomizer (RTA, RDA, RDTA) onto the Smok mod.
Do you have a smok alien with a Baby Beast Tank?
Feb 02, 2017 · Beantown Vapor's Kristyn K. gives you the complete lowdown on using your SMOK Alien Mod.
How do I set up my vape mod?
Dec 06, 2017 · I hope it worked and like and subscribe!
How do I access the settings of my Smok mod?
Feb 21, 2019 · Unfortunately, that is a risk with a device that has variable settings. To avoid running this risk, you need to be clued up on Ohms Law. This comprises a formula for determining the vaporiser's current, voltage and resistance. That formula is I=V/R, where ‘I’ means the current measured in amperes, ‘V’ refers to the voltage and ‘R ...
How to Use Smok Mods: How to Turn It on
Almost all of SMOK’s recent run of mods utilise a fire bar over a single fire button.This is a great method for firing your mod, as it requires ver...
How to Use Smok Mods: Exploring The Display
SMOK packs a lot of information into its mods’ displays.You have wattage and TC readings, dual-battery readouts, Ohms reading, voltage, and even a...
How to Use Smok Mods: How to Access Settings
If you’re using a touchscreen SMOK mod, there will be a settings icon on the homescreen which you can simply tap to access the mod’s settings.If yo...
How to Use Smok Mods: Moving Around Inside The Menus
When you enter the settings menu (THREE CLICKS on the fire bar), you can quickly skip through the settings menus by clicking the fire bar.SMOK mods...
How to Use Smok Mods: Installing A New Coil
When you change the coil on your tank, especially if you’re using an RDA, the SMOK mod will ask you if it is an NEW or OLD coil and give you two po...
How to Use Smok Mods: Quick Settings to Remember
1. Quickly Switch Between SOFT, NORMAL, HARD, MAX: on a non-touchscreen SMOK mod, simply press the fire bar and the up button at the same time. Fro...
How to Use Smok Mods: How to Upgrade Smok Mod’S Firmware
First and foremost, make sure you have SMOK’s NuMicro ISP Programming Tool installed on your PC.Once this is installed, you need to follow the step...
Have You Seen Our Best Sub Ohm Tanks of 2018 List?
No? Where you been!?We recently published our guide to the best sub ohm tanks for 2018.We tested A LOT of tanks. Too many to remember.But these are...
How To Use SMOK Vape Mods: How To Turn It On
Almost all of SMOK’s recent run of mods utilize a fire bar over a single fire button. This is a great method for firing your mod, as it requires very little precision, you can do it blindly, and the overall motion is more intuitive.
How To Use SMOK Mods: Exploring The Display
SMOK packs a lot of information into its mods’ displays. You have wattage and TC readings, dual-battery readouts, Ohms reading, voltage, and even a puff counter so you can see how much you’re vaping each day.
SMOK Mod Short Atomizer Error
You can run into issues with your SMOK mod if the coil isn’t set up correctly, though this specific issue mostly affects home-made coils.
How To Use SMOK Mods: How To Access Settings
If you’re using a touchscreen SMOK mod, there will be a settings icon on the home screen which you can simply tap to access the mod’s settings.
How To Use SMOK Mods: Moving Around Inside The Menus
When you enter the settings menu (THREE CLICKS on the fire bar), you can quickly skip through the settings menus by clicking the fire bar.
How To Use SMOK Mods: Installing A New Coil
When you change the coil on your tank, especially if you’re using an RDA, the SMOK mod will ask you if it is a NEW or OLD coil and give you two potential Ohms readings.
How To Use SMOK Mods: Quick Settings To Remember
Quickly Switch Between SOFT, NORMAL, HARD, MAX: on a non-touchscreen SMOK mod, simply press the fire bar and the up button at the same time. From here, you can then cycle through the output settings.