How do I Turn on/off my Smok vape?
First, locate your device’s main fire button, which also functions as the power on/off button. Most SMOK vapes have just a single button, sometimes two or three.
How can Smok help you upgrade your vape?
A SMOK representative may be able to assist you with tasks like updating firmware and can usually look up your product information to provide warranty details if applicable. Browse Cutting-Edge SMOK Mods to Upgrade Your Vape Experience VaporFi has an extensive selection of premium devices from SMOKthat you’re sure to love.
How do I set up different vaping modes?
In MODE SETTING, you can set up different vaping modes for different types of coil – W, Ti, Ni, SS, M – as well as adjust pre-heat, if you’d like to have this feature up and running. If you’re just wanting to vape, and aren’t bothered about doing anything fancy, just stick the mod in W (wattage) mode and adjust the wattage accordingly.
What should I do if my vape is too hot?
I. Normal circumstance: When you vape for a long time (eg：chain-vapes more than 10puffs with high wattage), it would give a "Too Hot" warning to protect the device itself. Please take out the batteries (if it's replaceable) and let it cool for 15 mins. II.
How do I adjust my Smok vape?
0:402:56SMOK Nord 4 Kit Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow let's move on and get your pods set up and ready to vape firstly take one of your pods that'sMoreNow let's move on and get your pods set up and ready to vape firstly take one of your pods that's provided in the box and remove the coil from the bottom of the pod like.
How do you change the mode on a vape?
Most mods will allow you to change between modes by pressing the fire button three times rapidly, and then either scrolling through using three more clicks of the fire button, or using the + and – buttons.
How do I reset my Smok?
Reset the tank - You can 'reset' the tank by removing it from the mod, checking the screws are tight and pressing the fire button. Then re-attach your tank and select “n” when you are asked if it is a new coil.
What does soft normal and hard mean on a vape?
When you use the “Hard” setting, the coil will reach its maximum temperature almost instantly when you press your mod's fire button. When you use the “Soft” setting, the coil temperature will ramp up slowly. So, how can you tell what the right vaping wattage is for your vape tank?
What settings should I have my vape on?
As a general rule, dab temperatures are set between 315℉ to 900℉. Below 315℉ is usually too low to vaporize cannabis concentrates. And above 900℉ can release carcinogens as well as a harsh, burnt vapor.
How do you use a Smok vape?
Turning on Your SMOK VapeFirst, locate your device's main fire button, which also functions as the power on/off button. ... Once your device is unlocked, press the main fire button three times to access the device menu. ... After you've enjoyed a good vape session, turn off your SMOK device by accessing the menu system again.
How do you reset the SMOK vape puffs?
2. you can set the “puff clear ” or ” puffs reset”. click “NO”, that quit resetting the puff, you can vape go on. click “YES”, puff data will be set too, you can vape from 0 to the daily vape value you set.
How do you reset Smok Nord 4 puffs?
Device On/Off – Press fire button 5 times in 2 seconds. Puff Reset – Number of puffs will reset when you reach 999.
How do you fix SMOK rpm?
If you're having trouble getting your SMOK RPM 2 to charge, the first thing that you should do is try charging the device with a different cable. If the RPM 2 still doesn't charge, try connecting it to a different USB port. You should generally charge the SMOK RPM 2 with a computer's USB port.
How do you get a smooth hit on vape?
Use higher-VG vape juices: VG is great for clouds, but the throat hit is really smooth at anything over 70 % VG. Reduce your power setting: Lower-power vaping keeps the vapour cool and the throat hit gentle. Choose a sweet flavour: Sweet, creamy or bakery e-juices offer a generally smooth throat hit.
Why is my Smok burning my throat?
Dry Hit. If you inhale when there is no vaping juice to vaporize, you will experience a "dry hit." This can cause a burning sensation that is very uncomfortable. This will temporarily cause a sore throat.
What does A and P mean on a vape?
You can scroll through these three modes, labelled A, P and A&P on the screen, by pressing the fire button three times consecutively. In A&P, you're free to simply draw on the mouthpiece or press the fire button; both will activate the built-in battery.
How to Use Smok Mods: How to Turn It on
Almost all of SMOK’s recent run of mods utilise a fire bar over a single fire button.This is a great method for firing your mod, as it requires ver...
How to Use Smok Mods: Exploring The Display
SMOK packs a lot of information into its mods’ displays.You have wattage and TC readings, dual-battery readouts, Ohms reading, voltage, and even a...
How to Use Smok Mods: How to Access Settings
If you’re using a touchscreen SMOK mod, there will be a settings icon on the homescreen which you can simply tap to access the mod’s settings.If yo...
How to Use Smok Mods: Moving Around Inside The Menus
When you enter the settings menu (THREE CLICKS on the fire bar), you can quickly skip through the settings menus by clicking the fire bar.SMOK mods...
How to Use Smok Mods: Installing A New Coil
When you change the coil on your tank, especially if you’re using an RDA, the SMOK mod will ask you if it is an NEW or OLD coil and give you two po...
How to Use Smok Mods: Quick Settings to Remember
1. Quickly Switch Between SOFT, NORMAL, HARD, MAX: on a non-touchscreen SMOK mod, simply press the fire bar and the up button at the same time. Fro...
How to Use Smok Mods: How to Upgrade Smok Mod’S Firmware
First and foremost, make sure you have SMOK’s NuMicro ISP Programming Tool installed on your PC.Once this is installed, you need to follow the step...
Have You Seen Our Best Sub Ohm Tanks of 2018 List?
No? Where you been!?We recently published our guide to the best sub ohm tanks for 2018.We tested A LOT of tanks. Too many to remember.But these are...
How to use a smok mod?
How To Use SMOK Mods: Installing A New Coil. When you change the coil on your tank, especially if you’re using an RDA, the SMOK mod will ask you if it is a NEW or OLD coil and give you two potential Ohms readings. Select the one that is the same as your coil – if it’s new, basically, just hit the NEW option.
How to change the color of the fire bar?
From the Home screen, Click THREE times on the fire bar. Click through the menus until you reach Screen Setting. Use the buttons on the mod to move through the options until you find the color you want. Once you have the color you want, hold the fire bar for ONE SECOND. Done.
Can you fire a mod with homemade coils?
If there are any issues and/or problems with the coil, its resistance, or the connection, the mod will simply not fire and likely show an error message.
Does Smok update firmware?
SMOK does release firmware updates every now and then but these seldom change the look and feel of the UX (user experience) or how the mod’s menus and settings function. Normally, the firmware just adds more power and fixes known bugs. PLEASE NOTE: this guide is designed for newbie vapers.
Why is my vape so hot?
I. Normal circumstance: When you vape for a long time (eg：chain-vapes more than 10puffs with high wattage), it would give a "Too Hot" warning to protect the device itself.
Can you touch a vape for a long time?
I. Normal circumstance: When you vape for a long time, you might feel it is overheated that you can't even touch it. Please take out the batteries (if it's replaceable) and let it cool for 15 mins. If the problem still exists, please try to contact us here: https://www.smoktech.com/support.
Why won't my Smok vape turn on?
Here are a few common reasons that your SMOK vape won’t turn on: : 1 The vape battery needs to be charged. Have you charged your vaporizer recently? You should have a pretty regular charging schedule and make a habit of plugging it in at the same time every day. Make sure that the cord is fully inserted, and always confirm that the USB light turns on to indicate that the device is in charging mode. 2 If the battery is dead, you can push the button a hundred times, but the result will be the same – it won’t turn on. Try charging your device fully, and then make another attempt to power it up. 3 There’s a faulty connection somewhere in your SMOK vape. Whether it’s a bad charger or a firing pin that’s getting stuck, anything that leads to an incomplete electrical connection is going to be an issue. It could be that your firing pin has vape juice on it, or it might not be coming in contact with the charger. 4 If your battery has grime or dust on its connection points, that could be causing the problem as well. Use dry tissue or a cotton swab to gently clean the connection points, and then try the charging process again.
How many clicks to unlock vape?
Unlock your device, which you can typically do with 5 clicks in rapid succession. Most vapers simply get in the habit of clicking the button rapidly until the indicator light turns on, so you don’t have to literally count out five clicks every time.
What to do if battery is grimy?
If your battery has grime or dust on its connection points, that could be causing the problem as well. Use dry tissue or a cotton swab to gently clean the connection points, and then try the charging process again.
Do smok vapes have a lock?
If your specific device has more than one button, and you aren’t sure which one is the main fire button, take a quick look at your instruction manual. Most SMOK vapes also have an online manual that you can find with a quick internet search. SMOK vapes have a lock system.
Why is my vape not working?
If the vape appears to be on, but the display is dark, you may have accidentally activated “stealth mode.”. Quickly press the fire button three times to turn off stealth mode. If this doesn’t work, you may need to upgrade your firmware. Otherwise, the problem might be caused by screen damage or another related issue.
How long should I soak my SMOK coil?
Allow the coil to soak inside of the tank for about 20 minutes, then take a few dry puffs before using the fire button to begin vaping. Check your output wattage. Make sure that your mod’s output matches the recommended output wattage on the side of the SMOK coil.
What is the best brand of vape?
There’s no doubt that SMOK is one of the vape industry’s best brands, crafting top-of-the-line mods and pod systems like the SMOK Nord, SMOK Morph, SMOK NOVO, and so many more.
How to fix a coil that tastes burnt?
Here are a few suggestions for how to fix coils that taste burnt: Replace your coils when needed. Expect to replace coils every few weeks or so (or about 50mL of e-juice, according to SMOK guidelines). Burnt-tasting coils are usually the first sign that it’s time to switch them out for new ones.
Why is my ohm error so high?
If you’re working with a rebuildable atomizer (RBA), the resistance of your coils may be too high or low. Adjusting the resistance will usually clear the error. Or, you may need to tighten the screws properly. Other reasons you may see an ohm error include: The resistance detection component of your device is broken.
Can you fix a dead vape mod?
Luckily, as just about any seasoned vaper will tell you, problems with a vape mod are often very easy to fix, being forced to replace a dead mod is a pretty rare occurrence. Often, a seemingly serious mod issue is simply the result of user error and can be resolved in next to no time.
How to get the best performance from a Smok Novo?
In order to get the best performance possible from your SMOK NOVO, you’ll want to prime the coils. Priming your SMOK NOVO’s coils ensures that the cotton inside the coil is adequately saturated before you use it and this, in turn, ensures you get great flavor from the first draw.
How to prime a Smok Novo coil?
And here’s how you prime your SMOK NOVO coils: ensure there is no juice in the pod when you remove it; take the new coil, drop vape juice onto the cotton, a few drops will do; insert it into the pod, fill with juice. Next, make sure there are no air bubbles.
What does it mean when your Smok Novo tastes burnt?
If your SMOK NOVO tastes burnt, it means the coil is spent. As soon as the flavor of your vape juice starts deteriorating, this is a sign that the coil is failing and you should think about swapping it out for a new one. Using the right type of vape juice is important too.
How many puffs does a smok novo have?
The cotton around the coil only has a certain amount of cycles – usually about 400 puffs – before it breaks down to the extent that it can no longer produce flavor. When this happens, the SMOK NOVO will produce a burnt taste. This means the coil is spent and it is time to replace it.
What is the size of a smok novo?
SMOK NOVO – The SMOK NOVO is the OG version of the line; it was the first pod vape to carry the branding NOVO. It has dimensions of 88.3 x 24.3 x 14.3mm and it uses a 450mAh battery.
Why does my Smok Novo autofir?
The autofiring issue on the SMOK NOVO is caused by vape juice getting into the air sensor. In order to stop the SMOK NOVO from autofiring, you’ll need to take the NOVO apart and wipe away any errant vape juice residue from inside the device.
Does the Smok Novo have buttons?
Designed to be compact and simple to use, the SMOK NOVO does not have any buttons and/or settings for you to worry about. Like the JUUL vape, the SMOK NOVO is a plug and play device – you fill up the pod with vape juice, insert it, power the device on, and start vaping. Simple, right? It really is.
EIHYPI Moved On ECF Veteran
I know that my Revenger has an option to take a hit on hard, medium or soft. Even though I have been vaping for quite some time I have never messed with these particular settings.
Letitia Citrus Junkie ECF Veteran
I've tried all these settings and always go back to normal. Would probably use hard if I did tc.
Wraith504 Ultra Member Verified Member ECF Veteran
VW-HIGH mode : The kit provides a higher start watt in the first few seconds to bring you a stronger hit and wonderful vaping experience.
gofishtx Vaping Master Verified Member ECF Veteran
I know that my Revenger has an option to take a hit on hard, medium or soft. Even though I have been vaping for quite some time I have never messed with these particular settings.
FΛDED Senior Member ECF Veteran
It's ramp up, how long it'll take to fire your coil at a certain setting. Soft's usually slower, if you want a longer deeper inhale. Hard's faster, for quicker shorter pulls. But, any mod can be like that - just raise or lower your wattage..
Letitia Citrus Junkie ECF Veteran
It's ramp up, how long it'll take to fire your coil at a certain setting. Soft's usually slower, if you want a longer deeper inhale. Hard's faster, for quicker shorter pulls. But, any mod can be like that - just raise or lower your wattage..
Wraith504 Ultra Member Verified Member ECF Veteran
It's ramp up, how long it'll take to fire your coil at a certain setting. Soft's usually slower, if you want a longer deeper inhale. Hard's faster, for quicker shorter pulls. But, any mod can be like that - just raise or lower your wattage..