Fit the coil into the base of the tank and tighten by hand with a suitable amount of force that will allow you to unscrew it. Fill your tank with your favourite e-liquid, then leave your device upright for 5-10 minutes to give the juice a chance to soak and saturate in your coil.
How to Prime a vape coil?
The first step is to prime a new coil. To prime a coil place a few drops of e-liquid into the cotton visible from the top of the coil. Then put a drop or two into the side juice ports. Then assemble the tank, fill with vape juice and wait at least 10 minutes to allow the wick to fully saturate.
How do vape coils work?
It is the coil that takes the power from your vape battery and turns it into heat, which is then used to turn e-liquid into vapour. Inside a standard coil model, you will find a length of coiled wire wrapped around an absorbent wick. The wire creates heat, while the wick absorbs the e-liquid held in your vape tank.
What is temperature control on a vape device?
Temperature Control mode enables you to adjust the maximum temperature your coils will reach, allowing your device to alternate between the correct wattage output as you vape. Ceramic Vape Coils: These coils either include a porous ceramic wick rather than a regular cotton wick, or a mixture of both.
Why does my vape coil taste burnt when vaping?
A vape coil has a cotton wick, and the wick is a bit like the cotton ball in the example above in that the fibers will trap air. If air is trapped in your coil’s wick, then the wick isn’t completely saturated with e-liquid. If the wick isn’t completely wet, you’ll get a burnt taste when vaping and may even ruin the coil.
Should vape coils be spaced?
Space. When the spaced and contact coil is the same resistance, spaced coil has larger space and horizontal space then contact coil. So the compatibility for a vape tank may not as good as the compressed coil. It is even difficult to install a standard spaced coil into a on drippers with small space.
How do you space a coil?
1:582:32Perfectly spaced coils - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you just give it a little bit of a squash. Take the other one. Put it back onto the same ID.MoreAnd you just give it a little bit of a squash. Take the other one. Put it back onto the same ID. Give it a little bit of a squash. And there you are perfectly spaced coils every time.
How do you wick a coil perfectly?
4:118:05How To: Wick Coils Perfectly - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt is pulling a coil just a little bit. That's okay that it feels pretty good when you pull back andMoreIt is pulling a coil just a little bit. That's okay that it feels pretty good when you pull back and forth. And that's it now you have the perfect amount of wick.
How do I adjust my vape coil?
3:4711:11COIL BUILDING 101 - HOW TO MAKE VAPE COILS FOR BEGINNERSYouTubeStart of suggested clipEnd of suggested clipHold it in place where you want it. Okay maybe something like that and now you take your screwdriverMoreHold it in place where you want it. Okay maybe something like that and now you take your screwdriver. And you just tighten it down that's literally.
Do spaced coils give better flavor?
Noted benefits of spaced coils: In reality the flavour difference is extremely minimal and barely noticeable. I typically vape single wire coils, and have done back to back tests (same setup) with spaced/contact, and I never noticed much of a difference.
Why does my coil burn so fast?
Sub-ohm coils heat up much quicker than those with a higher resistance. If your e-liquid has a thinner consistency then the atomizer head can vaporize it too quickly, causing premature burning.
Why does my wick keeps burning in half?
This is a sign there isn't much juice in your coil and you're approaching a burning situation. Your wick needs time to get soaked again, like a “re-priming.” Since the coil will be hot, the simplest thing to do is just stop vaping for 5 to 10 minutes and let your tank do its job.
Why is my vape cotton burning?
When we vape at a wattage too high for our coil heads, the e-liquid in the wicking (cotton) vaporises faster than the wick is able to re-saturate, resulting in dry cotton burning!
How many puffs does a vape coil last?
On average, a decently constructed coil for a sub-ohm tank should last you 4 days to 1 week. If you vape less because you cannot vape during work hours, or you do not vape throughout the day, then your coils are likely to last twice as long.
How do you know when coil is bad vape?
Signs it's time to change your vape coilA burning taste. Vaping a dead coil will eventually result in an acrid, burning taste. ... Gurgling sounds. Vapes shouldn't gurgle. ... Weak or “off” e-Juice flavor. This often precedes a burnt taste. ... Low vapor production. The vapor produced by your coil will gradually lessen with time.
How many watts do I need for a .23 ohm coil?
Wattage range 20-45W.
How To Break In A Vape Coil
The process of how to break in a new vape coil is much like warming up before playing a sport. Or like letting the engines on the jet warm up before flying to Denver. Breaking in a vape coil is the same concept. A coil is simply a cylinder that contains the atomizer wire and cotton wick.
Step By Step Guide To Break In A New Coil
When you first install a new coil, set the wattage to the lowest recommended setting. To break in a vape coil, the first three puffs on a new coil should be at the lowest setting and three very short puffs. After those first three short puffs, take longer fuller puffs as you would normally do.
How do vape coils work?
Coils, which are sometimes referred to as atomisers, are the component of your vaping device that creates vapour.
What are the different types of coil?
MTL or “mouth-to-lung” coils are designed to replicate the experience of smoking a traditional cigarette. This means a tight draw and low power output. Generally, MTL coils are designed to be used with higher nicotine strength e-liquids, to further simulate the “throat hit” of a cigarette.
DuoPrime – a new era for coil design
At Innokin, we’re always looking for ways to improve the vaping experience. As mentioned previously, mesh coils are excellent at increasing e-liquid absorption.
What is rebuildable coil?
Rebuildable vape coils take flavour and cloud production one step further than Sub Ohm / Direct to Lung coils. Experienced vapers with good knowledge of Ohm’s law and battery safety may choose to rebuild coils in order to use specific resistance levels and other metals, such as Titanium or Nickel. In turn, this allows people to create highly personalised custom vaping sessions that can’t be experienced when using other coils.
What is MTL coil?
MTL refers to the beginner-friendly method of vaping, which involves slowly drawing vapour into the mouth before pausing and inhaling it into the lungs. Mouth to lung coils are high resistance (1.0 Ohm or higher), which means they produce less vapour but are able to provide enhanced e-liquid flavour. Due to their low vapour production, MTL coils also tend to last longer.
What is DTL vaping?
DTL is considered to be the more advanced method of vaping, which involves inhaling vapour directly into the lungs with one 3-5 second long draw. Sub Ohm / Direct to lung coils are low resistance (less than 1.0 Ohm) with the ability to produce larger vapour clouds.
What to Know
Have you noticed that your vape coils don't last as long as they used to? Here are a few reasons why your vape coils have to be replaced more frequently.
Stop Using Sweet E-liquids
If residue is behind the coil failure, switch to an unsweetened e-liquid, like Halo. The simple act of switching to unsweetened e-liquid can extend the life of your coils dramatically.
Make Sure Your Tank or Pod is Full
Vaping on a nearly empty tank can cause coils to burn. If, after you've examined your coils, you notice that the cotton wick is burned, it's likely due to it being insufficiently moistened while you vape. Make sure your tank always has sufficient liquid to prevent this from occurring.
Reduce the Wattage of Your Vape
Even a properly moistened coil will burn quickly if the wattage is too high. While lots of people enjoy producing thick clouds and use higher wattage to achieve them, doing so will burn your coils more quickly. The ideal strength of the wattage depends upon how you inhale.
What makes a vape warmer?
Warmer vapor and larger clouds are produced by low resistance coils while a cooler vape with less current is produced by high resistance. Despite its importance, the coil has a fairly simple mechanism. It is constructed from a coiled wire or a piece of mesh as well as wicking material (typically cotton).
What is dual coil atomizer?
Another new one are dual coil atomizers that use an equal amount of electricity to both coils, which help to lower the overall resistance. The dual coils use so much power, which begs the question “which battery do you need?” rather than “what tank do you need?”. With RDAs, there are different kinds of decks, some of which are equipped for dual or even triple coils which allows for better production of vapor.
What is nichrome vape?
Nichrome combines 80% Chromium and 20% Nickel, which allows it to heat up much faster compared to Kanthal, producing large amounts of cloud and providing a pleasant, warm vape. Nichrome is only used in wattage mode and Sub Ohm vapers love it because of this along with its quick ramp up time.
Can you make or mar your vape experience?
You can make or mar your vaping experience just by picking the right coil, which is why it’s important that you know what types there are, what their benefits are and the properties of each type. It will greatly help you by using this guide as a starting point, and then researching your coil before using it. Don’t forget to check if it is compatible with your vape pen or dry herb vaporizer device before using.
How to thread a wick?
The best way to thread your wick is to tightly roll one end of your wick down to a point so that it can be threaded through like a needle.
How long should a wick be?
Your wick should be 2-3 inches long so you should have plenty of room to roll one end while leaving the center of your wick loose enough to fill the coil. Once your wick is in place it is time to trim the ends and secure it. You don’t want to trim the ends off of your wick right at the ends of the coil.
Can you wrap a wick around a mesh?
If you choose to purchase wicks such as ekowool or stainless steel that come in a rigid mesh form, you may want to wrap your coil around the mesh when you are building instead of building the coil separately. This eliminates one step and makes it very easy to get your wick perfect every time.
Can you thread a wick through a coil?
Remember, you will need to thread your wick through your coils, so it needs to be able to fit. However, you don’t want it to be so small that it can easily slip out of the coils. Once you get the hang of this it’s pretty easy, but for your first few wicks, try to thread the wick through the coil and see how it fits.
What is a vape coil?
Vape coils are the replaceable element in vape kits and tanks. It is the coil that takes the power from your vape battery and turns it into heat, which is then used to turn e-liquid into vapour. Inside a standard coil model, you will find a length of coiled wire wrapped around an absorbent wick. The wire creates heat, while the wick absorbs ...
How to tell if a coil needs changing?
The quickest way to tell if your coil needs changing is by taste, if you notice a taste like burnt metal or fibre then we recommend replacing it straight away. If the cotton in the coil has taken on a dark brown or black colour it means that it has begun to deteriorate.
What is rebuildable coil?
Rebuildable coils have been created for the purpose of being used with rebuildable atomisers. They require a far greater knowledge to use safely, including knowledge of Ohm’s Law, battery safety and general vape knowledge. Rebuildable coils are the pinnacle of customisability, as they allow you to pick an exact resistance and use metals ...
What is mouth to lung vaping?
Mouth to lung vaping describes the process of inhaling vapour into your mouth and then carrying it into your lungs, the same way you would smoke a cigarette. This style is especially popular amongst new vapers as it feels very familiar.
How is coil resistance measured?
A coil’s resistance is measured in Ohms. Ohm’s Law describes the relationship between current, power and resistance, and is very useful to understand as it directly relates to vapour production, which can help you decide which coil is right for you. A common analogy for understanding Ohm’s Law is to imagine the plumbing in your home.
What to do if your coil is loose?
On your coil you may see small rubber rings, called O-rings, they act as a seal to ensure your tank doesn’t leak when it’s filled with e-liquid. Before installing your coil check that the O-rings are intact.
What are the ingredients in e-liquid?
The two main ingredients of e-liquid are VG (Vegetable Glycerin) and Propylene Glycol (PG), which are both widely found in food and medicine. The levels of VG and PG will always add up to 100%, for example, 70% VG / 30% PG or 50% VG / 50% PG.
How Do Vape Coils Work?
What Are The Different Types of Coil?
- MTL/”mouth-to-lung” coil
MTL or “mouth-to-lung” coils are designed to replicate the experience of smoking a traditional cigarette. This means a tight draw and low power output. Generally, MTL coils are designed to be used with higher nicotine strength e-liquids, to further simulate the “throat hit” of a cigarette. Yo… - DL/”direct-to-lung” coil
DL or “direct-to-lung” coils are designed to accommodate high power, large airflow and massive vapour production. These days, most DL coils use strips of mesh instead of traditional round wire. You can identify a coil head that’s intended for DL vaping by looking at the diameter of the coil in…
Round Wire vs Mesh – What’s The difference?
- Traditional round wire coils and coils made using mesh strips are both extremely common, but what’s the difference and which one is right for you? Typically, round wire is used for lower-wattage coil heads. This is because they perform very well at low temperatures. Also, the manufacturer can easily tweak performance by changing the wire thickness or number of wraps…
Duoprime – A New Era For Coil Design
- At Innokin, we’re always looking for ways to improve the vaping experience. As mentioned previously, mesh coils are excellent at increasing e-liquid absorption. What if there was a way to increase wicking efficiency even more using mesh strips? With this in mind, our engineers designed DuoPrime technology. DuoPrime works by implanting an outer layer of mesh between …