How do I lock my IJOY avenger?
IJOY mods require the user to lock the resistance when putting on coils; that's done by pressing the up and down buttons at the same time and holding them. You can adjust watts up to the full amount by pressing up first and then adjusting. To adjust the temperature you press down first and then adjust.
How do I turn on my IJOY Avenger vape?
POD Mode Press fire button three times within 2S, enter into the main menu,press "+" or "-" T button to switch to POD ", press fire button to confirm. A In POD Mode, press right or left button to adjust the voltage. 2.5V POD 4.02V PUFF 0000 COIL 0.650 B Avenger Baby/13 Page 8 6.
How do you use voice control on IJOY avenger?
4:488:39The iJoy Avenger 270 234W TC Voice Control Kit Unboxing and Quick ...YouTubeStart of suggested clipEnd of suggested clipAnd checking out the 13 voice controls the Avenger will respond to in short. You must say hello IMoreAnd checking out the 13 voice controls the Avenger will respond to in short. You must say hello I joy before the Avenger mod will respond to your commands.
How do I set up my IJOY vape?
How to Use IJOY WAND Kit:Power Off/ON. Put the device upside down. ... Vaping. Fill the tank with e-liquid, hold the fire button and inhale through the mouthpiece. ... Charging. ... Short-circuit protection: ... Low power protection: ... Over 10 second protection. ... Low power Alert:
What to do if you know of a button sequence?
If you know of any button sequences for specific devices, leave and comment and share them with the community. Chances are someone viewing this post will have the same mod as you, and the information you provide could potentially help them.
Do vaping instructions end up in the trash?
While manufacturers do provide instructions, in reality, they often end up in the trash along with the packaging of the product. We know how difficult it is to read those instructions, much less follow them, which is why we are always providing vaping guides.
Do vape mods have instructions?
We’re sure that since you tossed that instruction manual in the trash, you probably didn’t know that your vape mod has secret button sequences, just waiting for you to access them. We have been sharing these secret button sequences for a while on this blog, and we know how to use them. Do you? Here’s how!
How to increase wattage on a vape?
-To generally adjust the output wattage to enrich your vaping flavor, first unlock the touch buttons. Press the "DOWN" button to increase the wattage.
Who makes the Vaporesso Revenger?
The family of Revenger models is an iconic series designed and manufactured by Vaporesso for the safer, purer and richer vaping experience. How to operate Vaporesso Revenger settings is the first chapter to begin your vaping journey with a Vaporesso Revenger. This article will give you some guidance based on the common questions we get regarding Vaporesso Revenger, such as how to unlock Vaporesso Revenger or how to set the clock. The purpose of this article is help you get familiar with your kit more quickly.
How to tell if a new atomizer is attached to a mod?
" OLD LOAD: -, NEW LOAD: + " will appear on the display. If a new atomizer is attached, press " + ", the mod will read new resistance; if not, press " - ", the mod will read at locked resistance.
How to lock resistance in TC-Ni?
Lock/Unlock resistance:In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2) Mode, press the "-"and mode button simultaneously for 2s will lock/unlock the resistance level, “ ” will appear on the display . Attach a new atomizer will not change the locked resistance.
How to change CCT on a TC?
While on any TC mode, press the mode button three times consecutively to select CCT. Select and hold down the mode button to confirm and to implement any modifications to the temperature line using the plus and minus buttons (Ramp up time and consequent performance); move on to the next bar with a quick press of the mode button. When all modifications are final hold pressed the mode button to save and exit.
How to adjust temperature on TC-Ni?
Adjust temperature:In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2) mode , temperature can be adjusted from 100-315℃ or 200-600℉ by pressing up button or down button, up button to increase and down button to decrease. Each press of the up or down button will increase or decrease the temperature setting by 5℃ or 10℉. Long press up button or down button can rapidly increase or decrease temperature setting.
Is an electronic cigarette a smoking cessation device?
It is intended for usage by people over 18, NOT by non-smokers, children, pregnant or breastfeeding women, people with or at risk of heart disease, or people taking medication for depression or asthma. The electronic cigarette is not a smoking cessation device. 2.
What does H stand for in a VW mod?
As an advanced Variable Wattage mode, there are 3 levels of VW: H stands for High; N stands for Normal; S stands for Soft. The default setting is Normal. VW(H/N/S) will guarantee your mod’ s ability to skillfully select the adequate average wattage for your atomizer, according to its resistance reading, automatically.
Can you use a refillable electronic cigarette with nicotine?
This refillable electronic cigarette is intended for use with compatible liquid, which may contain nicotine. Nicotine is an addictive substance and its use is not recommended for use by the following:
How to smoke a rock?
the two easiest ways is first to take a swirly lightbulb, wrap it with a towel and break it so you have a curved tube . take the longest piece and clean it out, then you can either use it like that (heating the rock in the lowest part of the curve and toking thru the top of the bulb but careful not to cut yourself) or take a straw and fit it inside. second you can take a piece of tin foil put your stuff on that and light it from the bottom while using a straw/paper funnel to inhale the smoke that comes off. if you want a decent hit though, take any type of bottle, juice box etc and put one stra
How to inhale smoke from a red hot burner?
Take a spoon and put it o the red hot burner. Bend the mouthpiece so that you can hold it steady and drop a piece in it as you inhale through a toilet paper tube or something else that is at least a 1/2 inch wide so that you can inhale quickly and not waste the smoke. My ex showed me this when he was doing hard one night. I have never tried it with shards but assume the logistics are the same.
Do you have to heat up vape coils?
You’d have to apply a consistent amount of heat once you found the proper mixture and the proper temperature in order for it to produce enough vapor for it to be worthwhile. As is true with vaping any liquid, the risk of dry coils introducing your mouth to a very unique and unfriendly flavor would be present, and you would need to make sure that your coil and/or wicking stayed wet constantly while vaping.
Can you use a dry vaporizer for plant matter?
You wouldn’t want to use a vaporizer designed for plant matter. Dry vaporizers reach a temperature much higher than you’d need to create a vapor from the meth and probably just end up burning it and creating smoke, which you could do with a lighter and some foil. So you’d wan
How do you heat up a bong?
The milky white crystals are put into the bulb or the round bottom (where the water would go in a bong) and then heated gradually from outside the glass , making sure the flame is not on the glass, leaving a char and preventing heat transfer. The applied heat will slowly build up as the chemical laced substance melts into a hazy puddle and recrystallizes into a pool when heat is removed.
Can you vape liquid?
So to answer your question, it’s conceivable that any standard vaping device made for liquid would work if you made or had access to a proper solution with which to use it. I am pretty sure that the mixture would gunk up your heating elements fairly quickly, and the smell may be difficult to mask.
What do cell ratings actually tell us? Part 1B: Resting vs Under-Load Voltages
These voltages show us how the cell reacts to being used, or not used. They aren’t ratings or specs but they are important concepts for being able to best use the datasheet information.
What do cell ratings actually tell us? Part 3: Watt-hour (Wh)
In the previous post for this series I discussed the Capacity rating and how it can’t be used to judge the running time of a cell if it’s being discharged at above 1A or so. This is due to the voltage sag in the cell caused by its internal resistance. It forces the voltage lower during the discharge so you hit your low voltage cutoff point sooner.
