Step 8
- Put your Vape Mod back together by doing steps 1 - 2 in reverse. (Leave the mouthpiece of the top cap off).
- Careful, firing your Vape Mod produces heat and can make the device HOT!
- Fire your Vape Mod. If the coils are heating up, it has been fixed!
Can a dead vape mod be fixed?
Luckily, as just about any seasoned vaper will tell you, problems with a vape mod are often very easy to fix, being forced to replace a dead mod is a pretty rare occurrence. Often, a seemingly serious mod issue is simply the result of user error and can be resolved in next to no time.
How do I know if my vape mod is working?
Check the 510 connection. Located on the bottom of your vape tank, the 510 connection is a small metal prong that must maintain proper contact for your mod to work. Try screwing your tank in a little bit tighter and clearing off any dust from the 510 connection and the connection point.
What to do if your vape stops working?
If you feel like the vapor production has suddenly dropped, try recharging your device and see if that helps. If that doesn’t work, check to make sure your atomizer coilisn’t dry, and that the atomizer itself isn’t flooded.
How to fix a leaking vape tank?
Turn the vape upright to minimize leaks, and close its air holes when it’s stored in your purse or pocket. Tighten the O-rings and seals. Check all sections of the tank to confirm that all seals and O-rings are secured. Bump up the wattage.
Why is my vape mod not working?
If your device requires removable battery, it might not turn on without the cells being properly installed. So make sure the batteries are placed in proper position right after installing them. As cliche as it may sound, your vape mod might seem not working just because it's turned off.
How do I fix my vape device?
Try the following:Check if you've pressed the power. Check if you've pressed the power button too often and turned it off. ... Check if you need to charge it. ... Check for connection issues. ... Check our Battery Safety page. ... Check your atomiser. ... Check your 510 pin. ... Check your coil. ... Check your tank isn't over tightened.More items...
How do you reset a vape mod?
Reset the tank - You can 'reset' the tank by removing it from the mod, checking the screws are tight and pressing the fire button. Then re-attach your tank and select “n” when you are asked if it is a new coil.
Why is my vape flashing and not working?
The most common ones being: Dying battery: Most often, the vape pen will blink ten times when the battery is too low for proper vaping. To fix the issue, recharge the battery. Low voltage: If the battery is charged but the pen is still blinking, it could be due to a low voltage.
Can Vapes be repaired?
So when they stop working, or you're not able or sure how to remedy some apparently minor glitch, it's usually possible to fix it. You can certainly take your e-cigarette to your local vape shop so they can advise you, and possibly fix any problems — but you can always take a stab at it yourself first.
How do I know if my vape mod is bad?
If the wicking burns, you'll know it. Your juice will develop a really horrible burnt taste. If that happens, the coil must be replaced. Even with full juice, your wicking can burn if you turn up the power of your mod higher than the coil is meant to withstand.
Why does my vape tank leak?
The most common reason why a vape tank leaks is because it isn’t assembled correctly. A vape tank uses a complex arrangement of silicone o-rings and metal threads to keep the e-liquid where it’s supposed to be – and if anything is out of place, the e-liquid will begin to seep out of the airflow vents at the bottom of the tank.
How to tell if vape is burning?
The easiest way to identify why your vape tastes burned is by looking at the atomizer coil. If you look through the top of the coil, you’ll see the coil’s mesh or wire heating surface. If the heating surface is dark brown or black, you’re dealing with a problem that relates to e-liquid residue.
Why does my vape taste burnt?
If the heating surface of your coil is dark brown or black when you remove the coil from your tank, the reason why your vape tastes burned is because you’re using an e-liquid heavily sweetened with sucralose.
How long should I puff a vape?
Lastly, remember that your coil’s suggested wattage range is based on a puff length of about two seconds.
How many gaskets are needed for a vape tank?
A vape tank generally includes at least one set of replacement gaskets. Reassemble the tank slowly, making sure that none of the threads are misaligned. The threads on a vape tank are thin enough that it’s not too difficult to force the parts together even if the threads are crossed.
Why does my vape stop working?
Other Issues That Cause a Vape to Stop Working. In general, a long list of problems can be caused by poor maintenance of your device. Just like any other piece of machinery, your vape device needs to be properly taken care of in order to function well.
What to do if atomizer doesn't work?
If that doesn’t work, check to make sure your atomizer coil isn’t dry, and that the atomizer itself isn’t flooded. Finally, make sure that the electrical connection between the atomizer and battery appears to be functioning correctly, cleaning off any dust or grime that may have built up.
Why does my e juice leak?
One of the top causes of leaking e-juice is a seal that is either cracked, missing, or just misaligned . Your device has several different seals, so examine all of them to see if you notice any crimping, damage, or looseness. Replacing these is an inexpensive fix, and can solve your leak problem altogether.
Leaking
This occurs when e-juice escapes from your tank through the airflow system. Leaking can vary from a few drops of vape e-liquid to having your tank emptying all of its contents all over your vape mod.
Spitting and popping
This is when occasional super-hot droplets from your vape e-liquid shoot in your mouth when you are trying to vape. The droplets will spit in all directions, but if you are unlucky, some of the content can shoot up into the mouthpiece.
Preventing Spitting and Popping
Don’t over-prime your coil. When you put too much e-juice in the chamber, you can easily cause flooding issues and spit back.
Why is my vape not working?
Sometimes, a disposable vape that doesn’t hit isn’t working because the airflow sensor isn’t sensitive enough or because the sensor is blocked by condensation inside the device. If you cover one of the device’s intake vents with your finger ...
How to stop vaping from overheating?
Slow down. You can also help to prevent overheating by ensuring that you never leave your device in direct sunlight or in your car. If you’re already maintaining a slow vaping pace, your device might simply be producing a burned flavor because it’s out of e-liquid.
Why is my vape giving me weak hits?
If your disposable vape is giving you weak hits, one potential reason is that the nicotine strength simply isn’t right for you . Consider buying a device with a higher-strength e-liquid next time. If the device worked in the past and has suddenly become less satisfying, though – or you simply want to get a more intense hit from ...
How to get weak hits on a vape?
If you have a pod-based disposable vape, you might get weak hits if air bubbles form around the pod’s wicks. Tap the device gently on a table to break the air bubbles. After giving the wicks a few seconds to get wet, you should get some nice hits again.
Why does my vape stop hitting?
The most common reason why a disposable vape stops hitting is because it’s simply out of e-juice. The average disposable vape contains enough e-liquid for up to 200 puffs, but the operative phrase there is “up to.”.
Can you refill a vape?
If you want to refill your vaping device, you should buy a device designed for that. Before you try refilling a disposable vape, you should also know that, when the device is out of vape juice, the battery is also nearly dead – so you’ll probably end up wasting e-liquid.
Can you burn a wick on an e-cigarette?
Most disposable e-cigarettes lack any kind of temperature control functionality. If you maintain such a fast vaping pace that you’re continually vaping before the wick has a chance to absorb more e-liquid, you may burn the wick. Slow down.
Introduction
This guide will teach you how to take apart your Vape Mod completely, analyze which parts need to be cleaned, and how to correctly clean them.
Step 1 How to clean and maintain your Vape Mod
Although maintenance for your Vape Mod shouldn't be dangerous, it can be messy. It is recommended to do this on top of a paper towel.
Step 3
Many Vape Mods are different, you might have to take out your battery in a different way than shown.
Why is my vape not working?
If the vape appears to be on, but the display is dark, you may have accidentally activated “stealth mode.”. Quickly press the fire button three times to turn off stealth mode. If this doesn’t work, you may need to upgrade your firmware. Otherwise, the problem might be caused by screen damage or another related issue.
How to fix a coil that tastes burnt?
Here are a few suggestions for how to fix coils that taste burnt: Replace your coils when needed. Expect to replace coils every few weeks or so (or about 50mL of e-juice, according to SMOK guidelines). Burnt-tasting coils are usually the first sign that it’s time to switch them out for new ones.
What is the best brand of vape?
There’s no doubt that SMOK is one of the vape industry’s best brands, crafting top-of-the-line mods and pod systems like the SMOK Nord, SMOK Morph, SMOK NOVO, and so many more.
How long should I soak my SMOK coil?
Allow the coil to soak inside of the tank for about 20 minutes, then take a few dry puffs before using the fire button to begin vaping. Check your output wattage. Make sure that your mod’s output matches the recommended output wattage on the side of the SMOK coil.
Can you fix a dead vape mod?
Luckily, as just about any seasoned vaper will tell you, problems with a vape mod are often very easy to fix, being forced to replace a dead mod is a pretty rare occurrence. Often, a seemingly serious mod issue is simply the result of user error and can be resolved in next to no time.