Reinstall the coil and reassemble your tank until it's clean and dry. If you're still getting 'check atomizer' or 'no atomizer,' it's time to try another (new) coil if you have one on hand; even an old or burned coil will suffice as long as the same error message appears.
Full Answer
How to fix check atomizer on a pod vape?
How to Fix Check Atomizer/No Atomizer On A Pod Vape. 1 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points. 2 2. Check Your Contact Points for Damage. 3 3. Reseat your Coil/Pod. 4 4. Try Another Coil/Pod.
Why does my vape Say No atomizer?
An e-cig that says ‘no atomizer’ or ‘check atomizer’ is a message that no vaper wants to see. A source of frustration because this message flashing up on your vape mod most probably means that you cannot vape. If playback doesn't begin shortly, try restarting your device.
Why won’t my atomizer work with my mod?
While it’s somewhat rare these days, it is possible for an atomizer to not be compatible with a mod due to its 510 pin. If some atomizers work and others don’t, it’s likely a poorly designed 510 connection on the mod.
What to do if your atomizer is not firing?
So try to screw a different atomizer in. If your mod is now able to fire the new atomizer, then you know who to blame! For sub-ohm tanks with pre-made coils, sometimes, you just get a bad coil. Try using a different one from the pack.
How do I fix my vape check atomizer?
RecapClean all contacts on battery/mod, tank or pod.Remove and reinstall the coil (after cleaning)Try a new coil.Check the 510 pin and see if you can adjust it (mods/tanks)Try another tank on your mod.Try another mod with your tank.Adjust base of coil carefully if you can (mainly sub-Ohm coils)
Why does my vape say check atomizer?
“Check Atomizer” or “No Atomizer” will appear when your vape mod or pod vape isn't reading your coil correctly. This can be due to the 510 connector not reading properly (where the tank screws onto the mod), the coil not making proper contact inside of the tank, or possibly a short.
How do I reset my vape atomizer?
0:000:31How To Do A Factory Reset on Your IQC Vaporizer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce the reset is complete the vaporizer will vibrate and button lights will. Turn. Off you.MoreOnce the reset is complete the vaporizer will vibrate and button lights will. Turn. Off you.
How do I reset my Vaporesso?
3) Continuously pressing mode button 3 times to unlock the mode button. 4) When install a tank, it will automatic identify its coil material and resistance, press up (+) button for reset, down (-) button to use existing setting.
How do I get my vape to work again?
Break Air Bubbles. If you have a pod-based disposable vape, you might get weak hits if air bubbles form around the pod's wicks. Tap the device gently on a table to break the air bubbles. After giving the wicks a few seconds to get wet, you should get some nice hits again.
Where is the atomizer located in a vape?
Housed within the vape tank, an atomizer head contains a coil of thin wire and wicking material. We will go into the finer details a little bit later, but the atomizer creates vapour.
What is atomizer on a vape?
The e-cigarette atomizer is a heating element that turns e-liquid into vapor. It is usually made up of three parts: the actual heating coil, a mesh bridge and a wick that absorbs e-liquid. The atomizer is also known as a nebulizer.
Is an atomizer a coil?
The coil is a small part in an electronic cigarette which gets hot. A coil head is also known as an atomizer head. These are words for the same thing, the heating element inside an e-cigarette.
What does atomizer shortcut mean?
Coils may have a short Also, some people may misjudge the size of their builds, causing their coil to touch the chamber and short out—and that will cause an “atomizer short” or an “atomizer low” error. Remedy: For factory coils, first make sure your coil is properly seated. If it still doesn't work, try another coil.
Why is my vape not working?
There are several reasons why your vape pen may not be working properly. Some of these causes are easy fixes, such as oil setting and getting stuck in your cartridge. Others are more technical, like a battery, atomizer or coil issue. Most of the time, your vape pen isn't actually broken.
Why is my Vaporesso blinking red 5 times?
Why is my vape pen blinking RED 5 times and go out? The coil is short-circuited. The resistance value of the coil is too small.
How do you clean Vaporesso?
0:532:10How to Clean Your Vape | Sub-Ohm Tank and RBA Tank - YouTubeYouTubeStart of suggested clipEnd of suggested clipEven hot water for about twenty to thirty minutes. Once you're done go ahead and take the pieces outMoreEven hot water for about twenty to thirty minutes. Once you're done go ahead and take the pieces out and put them on either a microfiber cloth or a paper towel to let them dry off for a little while.
1. Bad coil connection
If you are using a sub-ohm tank, then it is possible that your coil was inserted incorrectly, or it was just not tight enough. So simply re-insert it. Sometimes it’s just as simple as that!
2. You are creating a short
If you are using a rebuildable tank, make sure your build is not touching the cap or any other metal piece of the deck. Also make sure your coil is in good shape and there are no breaks.
3. You have a faulty tank or coil
Sometimes there is nothing wrong with your mod and the issue well might be in your tank. So try to screw a different atomizer in. If your mod is now able to fire the new atomizer, then you know who to blame! For sub-ohm tanks with pre-made coils, sometimes, you just get a bad coil. Try using a different one from the pack.
4. There is no connection
Clean the 510 thread of your mod and the 510 pin of your mod. Maybe there is just something stuck in between. If this does not work, maybe the lack of connection is related to your coil.
What does it mean when an e-cigarette says no atomizer?
An e-cig that says ‘no atomizer’ or ‘check atomizer’ is a message that no vaper wants to see. A source of frustration because this message flashing up on your vape mod most probably means that you cannot vape.
How to get vape juice out of a tank?
Take the base of your tank off. Take care if it is full of fluid and make sure you can remove the base without the tank leaking. If not decant the vape juice out of the tank first. Now check that your coil is screwed into the base of the tank correctly.
What does it mean when your tank is sat flush with a rubber o-ring?
If you have over tightened your tank onto your mod, it can push the metal plate from the 510 connection up into the tank. This usually means that it is sat flush with a rubber o-ring. If this is the case then it won’t make a full connection to your e-cig.
How to get a tank to pop back into the correct position?
Take your tank off your mod and turn it off, or remove the battery. Then take something small, like a small screwdriver and very gently press down on the pin. You should feel the spring underneath and this can get it to pop back into the correct position. Try attaching your tank again and see if the message has gone.
Can a mod make a complete connection to a vape tank?
Over time the connection on your e-cig can gather dust, dirt and e-liquid. If this is the case and your mod can’t make a complete connection to your vape tank, then this message will display. Remove your tank from your e-cig and have a look at the threads and metal plate to make sure there are no larger pieces of debris there.
Why do vapers forget atomizer error messages?
They were added by the manufacturer to protect you from faulty atomizers, and to prevent firing mishaps that can cause damage or injury.
Why does my mod say no atomizer?
However, once you put your top cap on, the sides are touching the coil (usually because it’s either too large or protrudes to one side too much), and that causes your mod to show you a “no atomizer” or “short atomizer” error message.
What does it mean when your chipset says no atomizer?
When your chipset is responsible for an “atomizer short “or a “no atomizer” error message, it means that it’s preventing firing on the basest of levels. There’s nothing here that you can fiddle with or adjust to fix this.
Why does my vape pen leak?
There’s vape juice in your vape pen – leaky atomizers are damaged atomizers. When juice seeps into your circuitry, it can damage it and cause it to show error messages when there’s actually nothing wrong with the atomizer.
What does "check atomizer" mean?
One company may use the standard “atomizer short” error for a shorted coil, while another may say “check atomizer” for the same reason—or use it as an umbrella term for all atomizer issues.
Why do atomizers use peek insulators?
Almost all atomizers these days use PEEK insulators to separate the positive from the negative. Any damage to your insulators may cause a short, resulting in an “atomizer short” or a similar error.
What does it mean when your mod is low?
If that’s the case, check the resistance of your coil . Each mod will fire at a certain resistance range; if the resistance of your coil is lower than that, your mod will refuse to fire it.
Why is my mod not working?
Six reasons for your mod errors (and how to solve them) 1. Coils may have a short. It could be something as simple as a bad factory coil, a loose connection on your rebuildable , or the factory coil itself isn’t properly seated or missing an insulator. Also, some people may misjudge the size of their builds, causing their coil to touch ...
Why is my mod not connecting to the 510 pin?
It could be due to any number of reasons. Some are just poorly designed and fail with time, others are faulty and make it through quality control.
What is Vaping360?
The Vaping360 team is a diverse group of experienced vaping contributors. We strive to bring you the finest content on all things vaping. Don’t forget to follow us on Facebook and Instagram for more!
What to do if your coil doesn't work?
If it still doesn’t work, try another coil. If the new coil works, you just got a bum coil which happens from time to time. For rebuildables, make sure to check your coils and all the connections are tight. The screws on a post may loosen a bit after during the build process—they may also loosen gradually with time.