When you receive the No Coil Detected warning and it’s an issue related to the mod, it’s often an issue with the center pin in the 510 connector. Since the pin in the Aegis Legend is spring-loaded, the only way the mod can be the cause of the issue is if the pin got stuck in its lowest position somehow.
Full Answer
Why does my vape tank say no coil detected?
The Tank: A lot of the times a No Coil Detected warning isn’t arising due to the mod, it’s because of the tank or atomizer. Even though the mod may have a spring-loaded center pin within the connector, the tank’s 510 threaded connector may not be making contact with that center pin.
Does geekvape say no coil detected?
Since there are tons of GeekVape customers being affected by this GeekVape No Coil Detected warning, and unfortunately, a lack of customer support, Guide To Vaping feels the need to do what it does best, which is to provide vaping content that’s designed to help vapers.
How to test a coil without the tank on?
Back the positive / base connector on the coil out a 16th of an inch. Screw coil back in and test without the tank on. Found sometimes the positive post is pushed in a tad to much.
How to fix a vape that won’t start?
This simple solution of turning off your vape with the tank disconnected should fix the issue; if this doesn’t work, proceed with the next solution. If you own multiple tanks and mods, the second step would be to ensure that your mod and tank work properly. To do this, all you do is change the tank for a new one.
Why won't my vape detect my coil?
“Check Atomizer” or “No Atomizer” will appear when your vape mod or pod vape isn't reading your coil correctly. This can be due to the 510 connector not reading properly (where the tank screws onto the mod), the coil not making proper contact inside of the tank, or possibly a short.
Why does my vape pen say no coil detected?
If you press the firing button on your e-cig and you see the message 'no atomizer' or 'check atomizer' it means that your vape mod is not reading the coil within your vape tank properly. It can be because of the 510 connection, the vape coil itself or the bits in between.
What does heatsink do in vape?
A heat sink is a series of thin fins jutting out from an atomizer, topper, or dedicated heatsink adapter designed to dissipate heat and cool it more quickly.
How do you reset the coil on Aegis legend?
GeekVape Legend 2 Menu Once in Output adjustment mode, you can scroll down to adjust coil resistance and reset puff count by pressing the fire button. Press and Hold Fire & + button – Brightness Up.
Why is my vape on but not working?
If you're using your vape pen's battery correctly but it's not working, inspect the battery's contact point for damage or residue, like excess oil. If it seems clogged, clean it with rubbing alcohol and let it dry before reconnecting it to the cart.
How do you prime a vape coil?
To prime a new coil, simply fill your tank with e liquid and leave it to stand for a few minutes before vaping. As above, this will allow the cotton inside your new coil to absorb plenty of e-liquid ready for that first, tasty vape.
How do I reset my aegis Geekvape?
On/Off : 5 clicks of the fire button. Change Mode: 3 clicks of the fire button then using up down buttons to scroll. Once in Output adjustment mode, you can scroll down to adjust coil resistance and reset puff count by pressing the fire button. Brightness Up: Press and Hold Fire & + button.
What is TC NI mode?
TC mode is like a car that allows you to put the pedal right down, but you can also gently tap it to move the vehicle ahead slowly. With some mods you can set a custom curve, allowing you to control the speed and rate at which a coil is ramped up. This is a huge leap forward for the vaping industry.
How do I reset my Geekvape Aegis boost?
When you highlight power mode you can click the fire button to highlight the resistance then lock it by pressing the up button. Clicking the fire button again will highlight the puff counter and the up button will reset it to zero.
What is the guide to vaping?
Guide To Vaping is the largest online magazine blog that is dedicated to providing a vast selection of helpful and informative articles about the latest vaping news, vapor products, and CBD.
What is the 510 pin on a circuit?
Make sure the connection points or coil leads are intact and seated properly. Sometimes the connection points will cross over to the opposing polarity. One lead is supposed to touch the positive side of the circuit, which is normally the 510 pin at the base, and the other isn’t supposed to be anywhere near it.
Is it rare for a manufacturer to release a product that is faulty?
Although quality control can often raise a concern with the non-stop outpour of products that make their way to the market , it’s very rare for a manufacturer to release a product that is faulty, especially since extensive testing is conducted by GeekVape before these products are set for release.
Is GeekVape a mod?
While GeekVape has a fascinating arsenal of products under its belt, including its popular Aegis Mod series, there are well more than a handful of GeekVape customers that are disgruntled due to a problem that is becoming consistent throughout the series.
stols001 Moved On ECF Veteran
Hmm... I don't have any experience with the smokalien, personally, I believe some folks have had that issue and it could be the 510 pin on the mod being stuck, or even gunked with a bit of juice? I'd try cleaning the mod thoroughly and focusing on the 510 pin and the battery contacts.
stols001 Moved On ECF Veteran
Well, it sounds like something is up with the center pin, at least for that tank. It really shouldn't be, since your tank and mod are both smok products right? But it seems that may be the issue. If your friend can't help, I would perhaps take it to a B&M to see if they can help with this issue-- maybe a small spacer would help?
SteveS45 Moved On ECF Veteran
The center pin on a Baby Beast is NOT adjustable and it sounds like a problem with the coil or the contact in the base of the tank.
YKruss Ultra Member ECF Veteran
I have couple tanks that have short 510 connections and any mod I put them on will scream "No atomizer" or "Check atomizer".
Gahh Super Member Verified Member ECF Veteran
You can try taking the baby beast coil out.. Back the positive / base connector on the coil out a 16th of an inch. Screw coil back in and test without the tank on.
Gahh Super Member Verified Member ECF Veteran
Tried everything... what should i do. I dont have money to buy another tank
Gahh Super Member Verified Member ECF Veteran
I have couple tanks that have short 510 connections and any mod I put them on will scream "No atomizer" or "Check atomizer".
Is a coil reader expensive?
They’ re not expensive and can help you out with much more than just figuring out the wattage range of the coil. If you put a coil on a reader, even if it’s the one built-in to your mod and it reads anything other than what you expect, it may have a problem.
Can you turn a coil in its seat?
If you can still turn the coil in its seat, its not tight enough. Make sure that you have no debris inside the coil housing. Something as simple as a piece of plastic could prevent a solid connection and cause an atomizer short. Get into the habit of checking it and wiping out the area every time you open up the tank.
Disconnect Your Tank from the Mod
The first thing you should do is disconnect your tank from the mod. Once you have done that and still see the message on your mod, turn it off and turn it back on. This simple solution of turning off your vape with the tank disconnected should fix the issue; if this doesn’t work, proceed with the next solution.
Change out the Tank and the Mod
If you own multiple tanks and mods, the second step would be to ensure that your mod and tank work properly. To do this, all you do is change the tank for a new one. If you change the old tank with a new one, the message disappears from your mod, which could mean that your old tank is the problem.
Check Your Coil
Sometimes the reason you see the “No Atomizer” message is because there is a problem with the coil. To check the coil for issues, you’ll first want to clean it. To do this, you’ll have to take the tank apart as if you were changing the coil.
None of the Solutions Worked What Now?
If none of these solutions worked, we are sorry to tell you that you might need to replace your coil, tank, or mod. Before investing in a mod, coil, or tank, we suggest you visit your local vape shop to see if they can fix it.
Conclusion
A “Check Atomizer” or “No Atomizer” message could bring many headaches; hopefully, however, you’ll be able to fix them with the solutions above.
