“Check Atomizer” or “No Atomizer” will appear when your vape mod or pod vape isn’t reading your coil correctly. This can be due to the 510 connector not reading properly (where the tank screws onto the mod), the coil not making proper contact inside of the tank, or possibly a short.
What does No atomizer mean on vape?
What does it mean when it says check atomizer? If you press the firing button on your e-cig and you see the message ‘no atomizer ‘ or ‘ check atomizer ‘ it means that your vape mod is not reading the coil within your vape tank properly. It can be because of the 510 connection, the vape coil itself or the bits in between.
How to fix atomizer on vape?
- There’s vape juice in your vape pen – leaky atomizers are damaged atomizers. ...
- You keep dropping your pen – one drop too much and you’re risking rattling the insides of your device. ...
- You’re over-tightening your atomizer – you should be gentle with your atomizer. ...
How to fix 'check atomizer'?
How to Fix Check Atomizer/No Atomizer On Your Vape Mod. How to Fix Check Atomizer/No Atomizer with a Vape Tank 1. Try Another Tank/Mod. This is the best way to know if there’s truly a problem. If you have another tank handy, you can try doing a switch. Take the tank off of your current mod and replace it with another tank.
How to clean your vape atomizer?
The cleaning agent rinse
- Baking soda is a good cleaning agent that can be used to get tanks sparkling again.
- Ethanol, aka grain alcohol, is yet another highly effective substance for cleaning. ...
- Cheap Vodka is not a household item, but chances are you can find it at the grocery store. ...
How do I fix my vape check atomizer?
RecapClean all contacts on battery/mod, tank or pod.Remove and reinstall the coil (after cleaning)Try a new coil.Check the 510 pin and see if you can adjust it (mods/tanks)Try another tank on your mod.Try another mod with your tank.Adjust base of coil carefully if you can (mainly sub-Ohm coils)
How do I reset my vape atomizer?
0:000:31How To Do A Factory Reset on Your IQC Vaporizer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce the reset is complete the vaporizer will vibrate and button lights will. Turn. Off you.MoreOnce the reset is complete the vaporizer will vibrate and button lights will. Turn. Off you.
How do you check atomizer?
0:373:22How To Fix 'Check Atomizer' - YouTubeYouTubeStart of suggested clipEnd of suggested clipSometimes juice likes to sit in the 510 of the device. So make sure you give this a clean also ifMoreSometimes juice likes to sit in the 510 of the device. So make sure you give this a clean also if there is juice or dirt inside the 510. Then your device may not be able to read your tank or RDA.
Why does my vape not atomizer?
If you press the firing button on your e-cig and you see the message 'no atomizer' or 'check atomizer' it means that your vape mod is not reading the coil within your vape tank properly. It can be because of the 510 connection, the vape coil itself or the bits in between.
How do I get my vape to work again?
Break Air Bubbles. If you have a pod-based disposable vape, you might get weak hits if air bubbles form around the pod's wicks. Tap the device gently on a table to break the air bubbles. After giving the wicks a few seconds to get wet, you should get some nice hits again.
Where is the atomizer located in a vape?
Housed within the vape tank, an atomizer head contains a coil of thin wire and wicking material. We will go into the finer details a little bit later, but the atomizer creates vapour.
How do you know if your atomizer is bad?
Signs it's time to change your vape coilA burning taste. Vaping a dead coil will eventually result in an acrid, burning taste. ... Gurgling sounds. Vapes shouldn't gurgle. ... Weak or “off” e-Juice flavor. This often precedes a burnt taste. ... Low vapor production. The vapor produced by your coil will gradually lessen with time.
How do I reset my Smok vape?
Reset the tank - You can 'reset' the tank by removing it from the mod, checking the screws are tight and pressing the fire button. Then re-attach your tank and select “n” when you are asked if it is a new coil.
How do you fix a vape that won't smoke?
Check your tank to make sure you have enough e-liquid. If your tank is completely full but you still have weak vapor, it is possible that your atomizer or coil has been flooded. If this happens, simply take your atomizer apart and clean it with a paper towel or gently blow through it to get the excess liquid out.
Is an atomizer a coil?
The coil is a small part in an electronic cigarette which gets hot. A coil head is also known as an atomizer head. These are words for the same thing, the heating element inside an e-cigarette.
How do I fix my Smok without atomizer?
1:176:58How to fix a no atomizer message on your vape - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd make sure you can remove the base without the tank leaking. If not then decal the vape juice outMoreAnd make sure you can remove the base without the tank leaking. If not then decal the vape juice out of the tank. First. Now check that your coil is screwed into the base of the tank.
How do I clean my vape?
In that case, you can follow these steps for deeper cleaning.Remove wicks from coils.Dry burn your coils lightly (don't let them glow too much)Remove atomizer from your mod.Place under running water.Brush them lightly with a toothbrush or a coil cleaning tool.Rinse once again.More items...
Why is my vape not recognizing my atomizer?
If your vape device isn’t recognizing your atomizer, it could be an issue as simple as an interrupted connection. Dust and debris can get in the way of the electrical current, leading to a complete mechanical failure. Other culprits can include an atomizer that’s completely screwed in, or a center pin that’s missing its mark. Take a close look at all the connection points on your device, clean them off, and make any adjustments to complete the current.
How to tell if a vape is malfunctioning?
One easy way to know if your atomizer is malfunctioning is if your vape displays one of the following messages: check atomizer, no atomizer, or no atomizer found. If your vape shows one of these no atomizer messages, continue reading to find out how to proceed.
What is a vaporizer?
A vaporizer is an electronic device, containing a battery that creates a very real electrical current. Above all, your safety should be your top priority. It’s easy enough to get a new atomizer or vape if yours has turned into a dud, but recovering from an injury that resulted from an overconfident, uninformed repair attempt is a much larger order.
How to prevent vaping issues?
Take a Proactive Approach. Many vape issues can be avoided by simply performing regular cleanings and maintenance on your device. Taking proper care of your vape can help you minimize issues, and keep your vaporizer running in tip-top shape. Cleaning your vape isn’t difficult, and takes just a few moments of your day.
What tool to use to adjust vape pins?
However, if your vape isn’t one of these models, use a small tool, like a precision flathead screwdriver, to adjust the pin position ever-so-slightly.
How long does it take to read a vaporizer?
Reading Time: 4 minutes . Your vaporizer is a lot like your car: you count on it on a daily basis, it’s a critical part of your everyday routine, and you hope to avoid issues at all costs. However, just like a vehicle, vaporizers do run into mechanical problems every now and then.
What is the pin on a vape?
The pin is the connection tip that’s found inside the 510 connector, responsible for making contact between your atomizer and vape device. If your pin is too low or too high, it can’t properly connect, and your device simply won’t work.
What does it mean when an e-cigarette says no atomizer?
An e-cig that says ‘no atomizer’ or ‘check atomizer’ is a message that no vaper wants to see. A source of frustration because this message flashing up on your vape mod most probably means that you cannot vape.
How to get vape juice out of a tank?
Take the base of your tank off. Take care if it is full of fluid and make sure you can remove the base without the tank leaking. If not decant the vape juice out of the tank first. Now check that your coil is screwed into the base of the tank correctly.
What does it mean when your tank is sat flush with a rubber o-ring?
If you have over tightened your tank onto your mod, it can push the metal plate from the 510 connection up into the tank. This usually means that it is sat flush with a rubber o-ring. If this is the case then it won’t make a full connection to your e-cig.
How to get a tank to pop back into the correct position?
Take your tank off your mod and turn it off, or remove the battery. Then take something small, like a small screwdriver and very gently press down on the pin. You should feel the spring underneath and this can get it to pop back into the correct position. Try attaching your tank again and see if the message has gone.
Can a mod make a complete connection to a vape tank?
Over time the connection on your e-cig can gather dust, dirt and e-liquid. If this is the case and your mod can’t make a complete connection to your vape tank, then this message will display. Remove your tank from your e-cig and have a look at the threads and metal plate to make sure there are no larger pieces of debris there.
1. Bad coil connection
If you are using a sub-ohm tank, then it is possible that your coil was inserted incorrectly, or it was just not tight enough. So simply re-insert it. Sometimes it’s just as simple as that!
2. You are creating a short
If you are using a rebuildable tank, make sure your build is not touching the cap or any other metal piece of the deck. Also make sure your coil is in good shape and there are no breaks.
3. You have a faulty tank or coil
Sometimes there is nothing wrong with your mod and the issue well might be in your tank. So try to screw a different atomizer in. If your mod is now able to fire the new atomizer, then you know who to blame! For sub-ohm tanks with pre-made coils, sometimes, you just get a bad coil. Try using a different one from the pack.
4. There is no connection
Clean the 510 thread of your mod and the 510 pin of your mod. Maybe there is just something stuck in between. If this does not work, maybe the lack of connection is related to your coil.
What does "check atomizer" mean?
One company may use the standard “atomizer short” error for a shorted coil, while another may say “check atomizer” for the same reason—or use it as an umbrella term for all atomizer issues.
Why do atomizers use peek insulators?
Almost all atomizers these days use PEEK insulators to separate the positive from the negative. Any damage to your insulators may cause a short, resulting in an “atomizer short” or a similar error.
What does it mean when your mod is low?
If that’s the case, check the resistance of your coil . Each mod will fire at a certain resistance range; if the resistance of your coil is lower than that, your mod will refuse to fire it.
Why is my mod not working?
Six reasons for your mod errors (and how to solve them) 1. Coils may have a short. It could be something as simple as a bad factory coil, a loose connection on your rebuildable , or the factory coil itself isn’t properly seated or missing an insulator. Also, some people may misjudge the size of their builds, causing their coil to touch ...
Why is my mod not connecting to the 510 pin?
It could be due to any number of reasons. Some are just poorly designed and fail with time, others are faulty and make it through quality control.
What is Vaping360?
The Vaping360 team is a diverse group of experienced vaping contributors. We strive to bring you the finest content on all things vaping. Don’t forget to follow us on Facebook and Instagram for more!
What to do if your coil doesn't work?
If it still doesn’t work, try another coil. If the new coil works, you just got a bum coil which happens from time to time. For rebuildables, make sure to check your coils and all the connections are tight. The screws on a post may loosen a bit after during the build process—they may also loosen gradually with time.
What are the problems with vaping atomizers?
The three most common atomizer problems are: Atomizer short warning. Atomizer low warning. No atomizer found warning. Those are the warnings that will typically pop up when you run into issues with the coil.
What is an atomizer in vaping?
Posted by Evelyn on August 8, 2019. Atomizers are the heart of vaping. Vape pens and mods are the power supply unit and the atomizers are responsible for vaporizing e-liquid. The term atomizer can refer to different things. It can refer to devices containing coils or it's also used to refer to the coil inside the device.
What does it mean when your coil is low?
The coil is too low in resistance in the mod thus displaying the "atomizer low" message. blockquote An atomizer low warning means that the device does not support the atomizer's resistance. This means that your atomizer's resistance is too low and is thus not compatible with your mod.
Why is there no atomizer found?
If the warning is still there after trying to fix it then it could be an issue with the mod being used. A "no atomizer" warning almost always means the coil being used is dead or loosely seated .
What is a RTA atomizer?
It can refer to devices containing coils or it's also used to refer to the coil inside the device. There are three types of atomizer devices: vape tanks , rebuildable drip atomizers (RDA), and rebuildable tank atomizers (RTA). These devices all use a coil that heats up and transforms vape juice into vapor.
Why does my atomizer give me a short message?
There could be a number of reasons why your device is giving you a short message. If you are using a rebuildable atomizer then your coil could be touching an unintended area like the deck or cap of the casing. If you are using a tank with a pre-built coil then the coil can either be defective or it could be loose.
How to fix an atomizer short?
How to fix an "Atomizer short" warning: Place batteries on an external charger to ensure they're both charging properly. For rebuildable atomizer users (RDA/RTA), make sure the coil is not touching the cap or deck and contains no breaks in your coil.
