Even with the battery fully charged, your vape pen may still fail to produce vapor. The most likely reason for this is that the firing pin doesn’t have proper contact with the battery, which can happen when the cartridge is screwed in too tight.
Full Answer
Why won’t my vape pen charge?
Sometimes your vape pen doesn’t produce any vapour even when the battery shows that it’s charged. When this happens the most likely cause is that the firing pin in the cartridge doesn’t have proper contact with the battery. This can happen when the cartridge is screwed in too tight.
What happens if you over-tighten your vape pen?
Over-tightening your vape pen can sever the connection between the battery and the cartridge. The 510 connection pin on the vape pen needs to connect with the cart to work. If you tighten the vape pen too hard, it can damage this important connection.
How to fix a burnt vape pen Wick?
Let your vape pen rest between hits to allow the wick to re-saturate with oil. Getting into the habit of cleaning your coil, as well as priming new coils, is another way to extend the lifespan of your coil while avoiding burnt wicks. Over-tightening your vape pen can sever the connection between the battery and the cartridge.
How to fix a leaking vape pen?
When the vape pen is being used, the airflow holes should be open enough that you can inhale with ease, without having to pull air in forcefully. The fix: Inhaling too hard can encourage flooding, which can lead to leakage and airflow problems. Inhale gently, and let the wicks on the coil do the heavy lifting.
How do you fix a vape cart that won't hit?
If you find that your vape cartridge isn't working, you may just need to clean out the contact area inside of your battery. You can do this easily with a cotton swab dipped in rubbing alcohol. Clean the area thoroughly, allow it to dry, and then attempt to use your vape cartridge again.
How do you fix a vape that won't fire?
Check your tank to make sure you have enough e-liquid. If your tank is completely full but you still have weak vapor, it is possible that your atomizer or coil has been flooded. If this happens, simply take your atomizer apart and clean it with a paper towel or gently blow through it to get the excess liquid out.
How do I fix my vape pen connection?
0:091:25How to fix your cannabis vape pen and cartridge connection issueYouTubeStart of suggested clipEnd of suggested clipAnd it's really easy to fix to bring it out so you'll want to grab a paper clip. And just gentlyMoreAnd it's really easy to fix to bring it out so you'll want to grab a paper clip. And just gently catch underneath the edge of the connector. And tug.
How long does it take for your lungs to heal from vaping?
After one to nine months: clear and deeper breathing gradually returns; you have less coughing and shortness of breath; you regain the ability to cough productively instead of hacking, which cleans your lungs and reduce your risk of infection.
Why does my pen blink when I try to hit it?
If the issue is a leak, turn off your battery and take a Q-tip dipped in rubbing alcohol and clean where the battery and cartridge meet. Make sure to dry them before screwing them back together. Another reason your battery may be flashing is because it may be dead and needs to be charged.
Why is my vape pen not firing?
One of the most common problems you’re likely to encounter with your vape pen is when the battery doesn’t fire the heating element ( firing pin). There could be a number of reasons behind this, but 2 are usually the problem. A. Problem with the connection plate: What you need to do here is to adjust the connection plate inside ...
Why is my vape pen not producing vapour?
When this happens the most likely cause is that the firing pin in the cartridge doesn’t have proper contact with the battery. This can happen when the cartridge is screwed in too tight.
How to check if a cartridge is pulling?
To avoid this, just ensure that the firing pin is pulled out to the point where it is flush with the bottom of the cartridge, which you can do by using the tip of a pocket knife, a razor blade, or paper clip. You can then connect it to a charged battery to check if it’s “pulling” properly.
What is the reason for a battery to short out?
Clean electrodes on battery, there is likely metal scraps that shorted the battery out temporarily.
Can you clean a vape pen with a firing pin?
B. The firing pin has residue on it: Vape pens are the most simple objects to clean and maintain, but not everybody does it. Cleaning regularly will not only extend its life but can help prevent problems with the firing pin. This can be done by dubbing the inside of the vape pen’s chamber with a cotton bud dipped in isopropyl alcohol, and you’re good to go.
Can a re-usable pen get plugged?
If you have a re-usable pen, it can sometimes get plugged while you’re taking a puff. If it does, try taking the reusable tip-off and gently blow into it on both ends. Sometimes a puff of smoke will come out when you do this, which instantly unplugs it.
Is vaping a good way to consume cannabis?
Vape pens are quickly becoming the trendiest way to consume cannabis because they’re very discreet and convenient, and we’ve got a ton of products to suit your particular taste. For example, you can now enjoy both our disposable and re-useable vape pens. Just so you know, re-usable pens come with a charger and refill cartridges and although they cost a little more, they’re well worth it.
Why won't my vape pen fire?
What your vape pen is telling you is that it won’t fire because it doesn’t have the appropriate tech connected to the battery.
Why is my vape pen not charging?
Even if you can’t see the difference between two chargers ( or two USB cables ) there’s a chance that something inside might be smidge different — and that smidge can be the cause of your device not charging.
What does it mean when a vape pen makes a gurgling noise?
Gurgling noises in a vape pen are almost exclusively a sign of a flooded tank.
How to use a vape pen properly?
When you inhale, make your drags long and steady; keep the vapor in your mouth; inhale it into your lungs, and then exhale. Remember — this is not a regular cigarette. You’ll need to change your angle of approach a lil’ bit.
Why is my e-juice leaking?
When your e-juice is leaking through the airflow holes, it doesn’t have to be that the issue is in the tank — the issue might be in the pressure or the juice that you’re using. Use thicker vape juice — or, you know, don’t leave your vape pen out in the sun because that will cause the juice to become more viscous.
What does it mean when a coil is cooking up your choice?
And the technical term for it is spitback. This means that the coil is cooking up your choice so hard, some of it flying out the chimney and hitting you straight in the top of the inside of your head!
How to force pen to go into menu mode?
Press the power button three times — this should force the pen to give some indication of life as it will usually force it to go into the menu mode.
How to fix a vape pen?
The fix: Take your vape pen apart carefully and clean the threading on the battery, the tank, the air holes, and the mouthpiece. Following this, you can reassemble the device and test it, taking gentle pulls and making sure to inhale slowly and not too forcefully.
Why is my vape pen drawing hard?
Drawing hard when you vape causes the wicks to absorb more concentrate than the coil can vaporize. Excess oil floods the tank and clogs the airflow holes. The fix: Take your vape pen apart carefully and clean the threading on the battery, the tank, the air holes, and the mouthpiece.
Why isn't my vape producing vapor?
“Oftentimes, the reason why your vape cartridge isn't producing vapor can be related to your voltage/wattage/temperature setting, ” explained Peki.
Why is my vape pen clogged?
A clogged vape pen cartridge. Vape pen cartridges can become clogged when the tiny airflow holes get blocked with oily residue after use, according to Winston Peki, editor of product-review site Herbonaut . “A simple way to fix this is by removing the cartridge from the vape pen, getting a needle, and simply gently poking the needle through ...
How to make your vape pen flow freely?
Getting the airflow setting right is key to ensuring your oil flows freely. When you're filling a vape pen cartridge, the airflow holes must be completely closed. When the vape pen is being used, the airflow holes should be open enough that you can inhale with ease, without having to pull air in forcefully.
What is a dab pen?
For starters, dab pens are designed to vape thicker concentrates, such as wax or roisin, which tend to have a higher viscosity than the concentrate liquid used in vape pens. However, some vape pens are compatible with both cartridges and wax.
Why are vape pens so popular?
Cannabis vape pens are growing in popularity due to their convenience and perceived safety in comparison to smoking. Nonetheless, more sophisticated inhalation methods can also mean more complex technical problems. If you've ever found yourself pulling hard on your vape pen only to end up with no airflow, you're not alone.
Why is my vape pen not working?
There are several reasons why your vape pen may not be working properly. Some of these causes are easy fixes, such as oil setting and getting stuck in your cartridge. Others are more technical, like a battery, atomizer or coil issue. Most of the time, your vape pen isn’t actually broken. More often than not, once you identify the issue with your vape pen, you’ll be able to troubleshoot.
How to turn on a vape pen?
Other vape pens use batteries with push-button atomizer activation. To turn these pens on, you’ll need to push the battery button five times quickly and hold the button down when you pull.
How to prolong the life of a vape pen?
Let your vape pen rest between hits to allow the wick to re-saturate with oil. Getting into the habit of cleaning your coil, as well as priming new coils, is another way to extend the lifespan of your coil while avoiding burnt wicks.
How to avoid burning a vape?
To avoid burning your cannabis oil and damaging your coil, use a lower wattage and a lower temperature setting on your vape pen. Using a higher setting can result in the atomizer vaporizing the oil too fast, and burning the wick. Additionally, taking shorter pulls reduces the heat exposure. If you take large draws, you’re more likely to burn your oil.
How to loosen up cannabis oil?
If you don’t have a hairdryer on hand, there are other ways to loosen up your cannabis oil. Heat a pot of water on a stovetop, until steam is produced. Then hold your vape pen over the steam for 20 seconds. This should result in the same effect as the hairdryer method, with your cannabis oil becoming less viscous.
How to get rid of a settled cannabis cart?
A common solution for freeing up your settled cannabis oil involves using a hairdryer to heat the cart. Separate the cart from the battery and set the cart upright. On its low setting, hold a hairdryer about six inches away from the cart. Apply heat for about 30 seconds. When you see bubbles forming, let the cart sit for a few seconds. Then reconnect the cart and take a pull. If your airflow is still obstructed, repeat the process again.
Why is my atomizer not working?
Over-tightening: A common cause of atomizer problems is over-tightening. If you tighten the atomizer with too much force, it can sever the connection with the device . If the connection is intact but it still isn’t working, there may be an issue with the center pin (510 connector).
Why does my vape wick burn?
Burnt Taste - Like with e-liquid atomizers, when you vape an oil atomizer with no oil inside, or do not let it properly soak up enough oil between hits, you can burn the cotton wick. This can also happen if you have the watts up too high. Once burned, every hit will carry a tainted taste. The only way to resolve this is to change the coil, if possible. Otherwise, always use caution and do not hit the atomizer with too many watts or without letting it absorb enough oil.
Why is it so hard to pull a hit from a vaporizer?
Difficulty Pulling/Taking a Hit - If you are having trouble pulling a hit from the vaporizer, the screen in the atomizer may be clogged and need to be cleaned or replaced. This screen prevents the contents of the atomizer from coming up through the mouthpiece and tends to get clogged from time to time.
Why isn't my atomizer working?
Atomizer Not Working / Check Atomizer Error - If your atomizer isn’t working or you get an error, then be sure it is screwed to the battery properly. It should be snug, but you don’t want to over tighten it as that can cause more problems. Some box mods detect the type of coil attached and won’t fire if the watts are set to a number higher than the attachment can handle. Ensure you are using the appropriate wattages. The coil may also be fried and need replacing. To ensure the problem is not with the box mod itself, try using the atomizer on another battery if possible.
Why does my vape coil taste bad?
However, your coil can produce a poor taste during the end of its life. If you notice a buildup of gunk on your coil and it is putting out a foul taste, that means it is time to replace the vape coil. A new vape coil will bring back the pure taste from the wax.
What are the problems with vapes?
Some common issues that can be found across all devices are the atomizer not firing, sticky messes from a leak, and a burned taste. Below you will find a list of these common issues and how to rectify them. If none of the solutions work, you may have a faulty vape that needs replacement.
What are the problems with wax vaporizers?
Each one will work a little differently, so a problem may be specific to a certain device. However, common issues such as sticky parts, coils not heating, and poor tastes can be found in any model. In this section, we will go over the most notable issues people have with wax vaporizers and how to resolve them.
Why won't my coil heat up?
Coil Won’t Heat - If your coil won’t heat up, first ensure it is properly attached to the battery. If that doesn’t resolve the issue, the coil may need to be replaced as they will burn out over time. Coils are powerful yet fragile wires that, like all things, break down after a lot of use. To prolong your coil’s life, be sure not to overpack your atomizer or poke the coil when loading it with wax. If you’re using a box mod, avoid setting the watts/temperature too high as this can also burn the coil out faster.
Why does my vape taste burnt?
Here are some common reasons why your vape pen may be giving you a burnt taste: You need a replacement atomizer head. You need to clean your atomizer head. You vape too soon after filling a new tank.
Why is my Ego not producing vapor?
If your eGo batteries is fully charged and the lights are one, but it is not producing vapor, you may have a firing pin issue.
Why does my clearomizer leak juice?
This can be caused from overfilling your clearomizer or from taking puffs that are too strong. Try to take slow and steady draws and be careful when filling.
Why is my E juice leaking from the bottom of my clearomizer?
For instance, if your e juice is leaking from the sides of the clearomizer tank (where the glass meets the metal), you may have screwed the clearomizer on too tightly, which caused a crack or a separation from the metal base. At this point you would just need a new clearomizer. Check out our Aspire ET-S 3ml Clearomizer
What happens if you overfill a clearomizer?
Overfilled Tank: if you overfill your clearomizer tank, this can cause it to leak.
How to fix ego twist?
The most common solution is to simply continua lly clean your atomizer heads within your tank and to replace your atomizer head when cleaning doesnt help anymore. Also, if your ego-c twist is giving you a burnt taste, just turn down the voltage.
What is the common way that you e juice down the center air hole this from leaving it in the hot car answer?
Hot Environment: Another common way that you e juice down the center air hole this from leaving it in the hot car.
Why does my vape pen blink?
8 Reasons Why Vape Pens Blink. 1. Low or Dying Battery. The most common reason for a flashing light on your vape pen is to indicate that your battery is running low. When there is not enough power coming from the battery, your vape will give a blinking light (a red light with some devices) to let you know it needs to be charged.
Why is my vape not connecting?
In some cases, the only issue is that your vape needs a quick clean and re-assembling. If any liquid has gotten on the connectors, or any of the threading is skew, it might be stopping your device from making a proper connection.
What happens if your 510 pin is stuck?
If the 510 pin has dropped or become stuck in the ‘On’ position, your vape won’t fire and will most likely give you a flashing light. If the staff at your local vape shop don’t do repairs, it might be time for a new mod.
What happens if you screw a battery mod on too tight?
If your tank has been screwed on too tightly or not tightly enough, it won’t make a connection and will give you a warning, usually in the form of a flashing light.
What happens if you drop a vape?
If at any point your vape has been dropped, the impact may have dislodged some of the smaller components inside your device . The more common of these is the connection between the battery mod and the tank: the 510 pin.
How to know if vape is full?
To see if this is the case, charge your vape until the light stays on (or stays green), indicating a full battery.
Why is my fire button stuck?
Unfortunately, like most electronics, vape devices do have some weaker components, mainly, the firing button. Because of general wear and tear or because some liquid leaked underneath, your fire button may become stuck.
How long does a vape battery last?
Typically, a vape battery can last for many years, depending on amount of use and care. Here are some tips to ensure your battery works optimally and consistently provides flavorful vapor:
How to clean a bong battery?
Unscrew your cartridge or charger from the battery and click the button 5x to turn it off. Take a cotton swab and dip it in 91% isopropyl alcohol, the same kind of stuff you use to clean your bong. Give both the battery connection and the cartridge coil or end of your charger (or both while you're at it, why not?) a nice scrub with the swab and let it dry before you reconnect the two pieces.
How to power an Ooze atomizer?
It may sound supremely obvious – but first – ensure your battery is on. If you have an Ooze battery, press the button five times fast within two seconds, without paus ing between clicks. If your battery is on, pressing the button will illuminate a light around the button and power the atomizer. If the battery is off, nothing will happen when the button is pressed.
What happens when you plug in a dead battery?
When you plug in your dead battery, both your battery and charger lights should illuminate. The charger light will be red the entire time the battery is charging. Once the battery reaches full charge, the battery light will turn off and the charger light will turn green.
What is the coil on a 510 thread?
Your 510 thread battery has a small round piece on the very bottom, this is your coil. Sometimes you'll unfortunately receive a defective cartridge from the dispensary and it simply won't connect with the heating element of the battery.
How to fix crooked battery?
If crooked, gently push the coil back into the correct position using a toothpick or bobby pin. Be careful! Pushing too hard can cause further damage to the cartridge, so make sure you pay attention to what you're doing.
What happens if you drop a battery in water?
Did you drop your battery on the ground or in water? Unfortunately, it could be permanently damaged if the internal connections have been interfered with. If nothing else is working, it may be time for a new battery.
