VAPE PEN 22 Airflow System 1) The tank uses top refill system, you just need to hold the tank with one hand, and use another one to screw off its drip tip and top cap, 2) Add e-liquid through the slot, and pay attention not to drip in into the central airflow tube. Attentions
How do you use a 22 vape pen?
Screw on the atomizer head to the battery tube, fit the glass tank over the head, fill with eliquid, and screw on the top cap. Press the fire button five times to turn the Vape Pen on or off, press and hold the fire button to vape. That's it. All the expected safety protections are built into the regulating chip.
How do I set up my Smok vape?
1:032:19Smok Nord Unboxing & Setup - YouTubeYouTubeStart of suggested clipEnd of suggested clipFind the fill port on the side and lift the cap fill. It up with your favorite e-juice. Today I'llMoreFind the fill port on the side and lift the cap fill. It up with your favorite e-juice. Today I'll be using mango buy salt shaker. Once your pot is full pulls the cap push the pod into the device.
Why does my Smok vape pen 22 Keep blinking?
Resistance protection: when the atomizer resistance is lower than 0.1 ohms or higher than 2.5 ohms, the LED light will blink 4 times and the battery will automatically shut down the output. 3.
How do you charge a 22 vape pen?
To charge the SMOK Vape Pen V2, connect the device to your computer using the included micro USB cable. The LED on the back of the device will indicate when the charge cycle is complete. The indicator glows red while the device charges, and it turns off when the device is fully charged.
How do you change the settings on a vape pen?
Most vape pens with buttons require five clicks to turn them on, three clicks to change the heat setting, and five clicks to turn them back off. The button heats the chamber as you hold it down, so be sure to hold the button down as you're taking your hit.
How do I adjust my vape settings?
How Do I Change Modes? Most mods will allow you to change between modes by pressing the fire button three times rapidly, and then either scrolling through using three more clicks of the fire button, or using the + and – buttons.
How do I get my Smok vape pen to work?
Here's how to fill the Smok Vape Pen V2 with e-liquid:Unscrew the drip tip Anti-Clockwise.Fill with your desired e-liquid.Re-fit the drip-tip cap clockwise.Allow the e-liquid to saturate the coil for around 5-10minutes.
How do you know when a Smok 22 is fully charged?
Ease of Use. When it comes to hassle-free operation, the Smok Vape Pen 22 has many other mods beat. Simply charge the device until the LED indicator stops flashing, meaning that the battery is fully charged.
What does 4 blinks mean on a Smok?
Resistance protectionResistance protection: when the atomizer resistance is lower than 0.1 ohms or higher than 2.5 ohms, the LED light will blink 4 times and the battery will automatically shut down the output.
How long does it take to charge vape pen 22?
The 1650 mAh battery lasts almost through a whole day of vaping. When it reaches 3.3V, you get an alert that you need to recharge through the blinking of the LED light. Thankfully, it only takes two hours to recharge, so you don't have to wait long before getting your next fix.
What does it mean when my vape blinks 3 times?
a short circuitCertain batteries will flash 3 times to indicate a short circuit. Most standard e-cig batteries will have what's called short circuit protection, so when there is a short and you press the fire button it will just blink 3 times and then won't do anything.
Why is my Smok vape flashing?
Short circuit protection: if a load short circuit is detected, the white LED light will flash 4 times and the battery will automatically shut down the output. 3. Low voltage protection: when battery capacity is lower than 3.3V, the LED light will flash 15 times and the battery will automatically shut down the output.