how to fix your vape when it says atomizer short

• Take the atomizer off of the vape
• If using a tank, open it and look at the coil. Ensure that the coil is properly secured to the bottom of the tank
• If the vape is an RDA, check and see if the positive and negative posts are screwed in. ...
• Take the tank off and reconnect it. If the message keeps coming up, replace the mod or find an atomizer that will work with the mod

Full Answer

What does it mean when your vape says short atomizer?

If you are using a vape tank with pre-built coils then check to make sure that the coil's base is connecting to your tank base. Pull the base of the coil out slight then reassemble the tank and make sure the coil is on tight. If the coil is on tightly and still reading atomizer short then you might have a bad coil.

What does atomizer short mean on a vape?

Mar 02, 2022 · If you believe that your vape mod should support the connected coil, follow the steps outlined above under the “Atomizer Short” error message. Clean the threading on your tank and vape mod. Make sure that your tank is assembled correctly and that all components are screwed in tightly and aren’t cross-threaded.

What to do when your vape says check atomizer?

Jun 22, 2020 · The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points. Take the pod out of your pod vape and check the bottom of the pod for any dirt or ejuice. Also check inside your vape where the pod attaches to it.

Why does my vape say check atomizer?

May 30, 2021 · With most vape mods, the coil’s resistance would have to be extremely high or extremely low for the mod not to work. That usually indicates that the atomizer coil has a manufacturing defect or isn’t installed properly. Replacing the coil should resolve the issue.

What is the atomizer in vaping?

This is a component that makes up a vape or e cigarette. The atomizer is a crucial piece of a vaporizer and without this component almost no vaporizer would work.

What is an e-cigarette atomizer?

E-cigarette atomizers are responsible for seeding e-juice mostly and not dry materials. These types of atomizers are often found between the mouthpiece in the tank and air responsible for heating up the E juice to output vapor through the mouthpiece.

Do you need to know all the technical terms for vaping?

There is a fair amount of technical information surrounding vaping, and it can sometimes feel a bit overwhelming especially with some of the terminology that people that vape often may use. It's very unlikely that you'll need to know all of the technical terms for vape components to use a vape successfully, but learning ...

What is a check atomizer?

Check atomizer is also called No atomizer. Atomizer shorts are often displayed when a coil begins to short-circuit. Atomizer short warnings will completely disrupt energy that goes into the atomizer to preserve it. Seeing these atomizer errors should never keep you from using your vaporizer.

Can you use preinstalled coils with a vape tank?

If you are using preinstalled coils with a vape tank, you'll need to make sure that the base of the coil is connected to the base of your tank.

Why is there no atomizer on my 510?

The no atomizer or check atomizer often comes up when the electrode pin in 510 configuration is not pressed against the firing pin, when the prebuilt coil is not connecting inside the base of the 510 electrode, or when the RBA is not correctly connected to the deck.

Why do you need to take up a new coil?

If the coil is interacting with the internal structure of your vaporizer you may need to take up a new coil or rebuild the coil so that it doesn't have the same break. Make sure any coil replacement you get is the right size and this can prevent the chance that it will touch the deck or cap.

What causes a short in an atomizer?

2. Insulator damage. Almost all atomizers these days use PEEK insulators to separate the positive from the negative. Any damage to your insulators may cause a short, resulting in an “atomizer short” or a similar error. Remedy: Inspect your insulators.

Can you over tighten an atomizer?

Overtightening atomizers – people often overtighten their atomizers, to the point where they break the 510 pin out and/or snap the ground wire internally. Don’t over tighten your atomizer. This is especially important here because often vapers will tighten their atomizer after receiving “no atomizer” errors.

What does "check atomizer" mean?

One company may use the standard “atomizer short” error for a shorted coil, while another may say “check atomizer” for the same reason—or use it as an umbrella term for all atomizer issues.

Why is my mod not working?

Six reasons for your mod errors (and how to solve them) 1. Coils may have a short. It could be something as simple as a bad factory coil, a loose connection on your rebuildable , or the factory coil itself isn’t properly seated or missing an insulator. Also, some people may misjudge the size of their builds, causing their coil to touch ...

What to do if your coil doesn't work?

If it still doesn’t work, try another coil. If the new coil works, you just got a bum coil which happens from time to time. For rebuildables, make sure to check your coils and all the connections are tight. The screws on a post may loosen a bit after during the build process—they may also loosen gradually with time.

Why do atomizers use peek insulators?

Almost all atomizers these days use PEEK insulators to separate the positive from the negative. Any damage to your insulators may cause a short, resulting in an “atomizer short” or a similar error.

Can you fire a mod if the resistance is lower?

Each mod will fire at a certain resistance range; if the resistance of your coil is lower than that, your mod will refuse to fire it. Remedy: If you are using a rebuildable, note that dry burning the coil may eventually raise its resistance.

What is an atomizer in vaping?

A vape atomizer is a device that heats up and transforms vape juice into smokable vapor.

What is an atomizer?

The term “atomizer” can be used to refer to different things, with regards to vaping. In some instances, it refers to devices containing vaping coils while other times it is used to refer to the heating coils inside the device.

What is a sub ohm atomizer?

An atomizer with a resistance level of less than 1.0 ohm is often referred to as a sub-ohm atomizer. During vaping, you turn on your vaporizer to active the battery that powers various components within the device. The power generated from the battery heats up the heating coil (or coils) inside the vape atomizer.

What is the wick on a vape?

Above the coils is the wick, soaked in your e-liquid. The wick can be made of a few different materials such as cotton. When the vape juice soaked in the wick comes into contact with the coil, it begins to heat up and turns into vapor once it reaches the required temperature.

Why does my vaporizer blink red?

For example, your device may blink red for error and green for normal operation. Once you’ve tested the batteries and confirmed that they’re working fine, you should move to the tank. You can connect the tanks to your vaporizer in two different ways.

What is the connection between a 510 and a vaporizer?

The other connection is the 510 connection that holds the tanks to the mod or device used. There must be a good connection between the vaporizer and the tank for the battery power to flow from the mod to the tank. Since you cannot see the connection, it’s advisable to check the coil for connectivity.

Why blow on coil?

You may want to blow on the coil to see the small amount of vapor produced and keep your coil from overheating. You can’t go wrong with all of the steps mentioned above. Patiently wait to see vapor coming from the coil before assembling back your vaporizer.

What causes a check atomizer short?

Loose pieces of metal on the build deck will cause your mod to display “Check Atomizer” or “Atomizer Short”. Even very small pieces or trimmings of wire can cause a short or a check atomizer error on an RDA/RTA/RDTA. First, inspect the build deck closely for loose pieces of wire or other foreign objects.

What to do if your pod vape isn't firing?

If your pod vape isn’t firing, has a blinking LED and won’t fire, or says Check Atomizer or No Atomizer, you can follow a few of the same steps listed above for tanks: 1. Clean Your Contact Points. The first step you should try if your pod vape isn’t firing or says check atomizer is cleaning out your contact points.

Why won't my 510 mod work?

Simply put, if your mod can’t read your tank and coil resistance properly, it won’t be able to deliver power and therefore won’t work.

Why is my mod reading the new tank correctly?

If your mod is reading the new tank correctly, it could be a problem with the coil on your other tank. You might also want to clean the contact points on the tank that was giving you the error. If your mod is still reading “check atomizer” with a new tank, it’s probably a problem with your mod.

How to remove a tank from a mod?

Start by removing the tank from the mod and inspect the threading where the tank screws in for dirt , dust, or ejuice. Do the same with the 510 connector on your mod. Clean out the contacts with a paper towel, and screw your tank back onto your mod.

How to clean a tank after taking apart?

Once you’ve taken apart your tank, unscrew your coil from the base of the tank. Now, you’ll want to clean the bottom of the coil where it screws into the tank and makes contact. You’ll also want to clean your tanks contact point with the mod as well. Once done, reseat your coil, and reassemble your tank.

What is a versed vaper?

The Versed Vaper team are a group of passionate and experienced vapers who take pride in writing helpful, quality content about vaping. From deals, to news and reviews, we've got you covered on all things vaping. Remember to subscribe to our newsletter, and follow us on Twitter, Instagram, and Facebook!

What does it mean when a vape mod says check atomizer?

The message “Check Atomizer” means that your vape mod isn’t detecting the connected atomizer coil at all. That may mean that the tank isn’t assembled correctly, that the tank doesn’t have a firm connection with the mod or that the coil itself has a problem. Use these steps to troubleshoot a “Check Atomizer” error.

What does it mean when a vape mod says it has a short circuit?

When your vape mod tells you that it has a short circuit, it means that something is critically wrong with the electrical circuit connecting the battery in your vaping device to the atomizer coil. You might get the “Atomizer Short” message, for instance, if unexpected metal-on-metal contact occurs inside your tank. For example, maybe the coil in your tank is cross-threaded, so the coil is seated a little higher in the tank’s base than it should be, and that’s causing the tank’s chimney to touch the heating wire inside the coil. A manufacturing defect in the coil can also cause a short circuit.

What does it mean when a vape mod says "Time Out"?

The message “Time Out” means that the length of your puff has exceeded what your vape mod’s puff timer will allow. Most vaping devices have built-in puff timers that help to prevent overheating. Suppose, for instance, that you’re carrying your vape mod in your pocket, and you’ve forgotten to lock it. You inadvertently push and hold the mod’s fire button when you sit down. Without a puff timer, that’s a potentially dangerous situation. With a puff timer, though, the device automatically cuts off, so its temperature stays in a safe range.

What does it mean when you see an error message on a mod?

If you see any of the above error messages on your mod, it means that the resistance of the connected atomizer coil isn’t within your device’s supported range. There are two likely reasons why you might see that error message.

Why is my atomizer shorted?

This can be caused by your coil not being in place, or it has been damaged or simply doesn’t fit. This is frequently due to human error rather than something being damaged. To fix this, take your coil out and try again.

What causes a shorted coil in a atomizer?

This is a very easy issue to fix and it’s all about making sure your coil is positioned properly. If it’s shorted, there’s no/very little current flowing through the atomizer. This can be caused by your coil not being in place, or it has been damaged or simply doesn’t fit.

What does "low atomizer" mean?

‘Low atomizer,’ ‘no atomizer,’ ‘atomizer low,’—although the exact wording may change, if your screen displays a similar message, it means there’s an issue with your vaping device. This can be a number of things, and in this article, I’ll help you identify the issue and fix it.

Can you leave a vape for too long?

There’s no point leaving it for very long, as they usually get worse with time, and some will leave your system permanently broken. You may not even be able to use your device at all if you have this message, and if you want to get vaping again, it’s best to fix it as soon as you can.

Why do atomizers use insulators?

Most atomizers use insulators to differentiate between the positive and the negative currents— and as you can imagine, if this goes wrong, it can be a serious hindrance to your vaping experience.

What to do if your coil doesn't match up?

If they don’t match up—the coil being lower than the mod—you’ll need to sort it. You can dry burn a rebuildable coil to raise its resistance, but this is a long process that will drain the battery. Alternatively, you can add a few wraps to your coil to help build upon the resistance.

What happens if you don't detect an atomizer?

If the atomizer isn’t detected, then the circuit can’t be completed, and so you won’t be able to use it. Unscrew your atomizer and see if anything’s blocking the circuit from being completed. Maybe you screwed it in at an angle, and the lack of symmetry wouldn’t work with the main body.