Cleaning the X-Max V2 Pro Cleaning supplies: Poker tool (included with X-Max VII Pro) Cotton Swabs Paper Towels 91% or higher Isopropyl Alcohol One pint of Elbow Grease Disassembling the XMax VII Pro is easy! The mouthpiece pops right off, and you can remove the screen assembly from the mouthpiece.
Is the xMax V2 Pro A good vaporizer?
If you’re looking for a compact conduction vaporizer, the XMAX V2 Pro is a solid choice, with an inconspicuous look and an interchangeable battery. It isn’t too difficult to get up and running, but our quickstart guide will walk you through the unboxing and setup process, as well as the steps for your first session. Is the XMAX V2 Pro good?
What is the best way to clean a vape?
For that, you'll need alcohol-based solutions, vinegar, or special vape cleaners. Distilled water and vinegar, rubbing alcohol, and vodka are all preferred cleaning solutions. Hydrogen peroxide can also work, but you can't mix it with anything else or risk a nasty chemical reaction.
How can I improve the quality of my vape?
You'll extend the life of the vape pen as a whole, even the battery. It will take less work to reach the same temps and draw out large volumes of vapor. We also recommend avoiding going the cheap route on your products. Browse through our store for some ideas on what you may need to improve your quality of vape.
How often should you clean your vape?
It ought to be cleaned weekly, if not at least a time or two each month. You should clean it more frequently if you're a regular user. A pleasant, fresh cleaning will keep your vape working up to its potential, free of developed residue, burnt material, and spit.
How do I clean my xmax V3 Pro?
For deep clean, immerse all pieces except plastic mouthpiece in isopropyl alcohol for 10-20 minutes, rinse thoroughly with clean water and dry before reassembling. Stainless steel oven cleaning: use brush to sweep inside and cotton swab dipped in isopropyl alcohol.
How do I pack XMAX V2 Pro?
0:272:31X MAX II Pro Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour botanical or wax into the chamber using your su scoop or stainless steel tool respectively. IfMoreYour botanical or wax into the chamber using your su scoop or stainless steel tool respectively. If you are loading wax. Remember to insert the wax gun.
How do you use the V2 Pro vaporizer?
Press and hold the button for 4 seconds and the V2 Pro Series 7 vaporizer will begin heating to the last pre-set temperature. The base will glow red, then orange then stay solid green once the temperature is reached and the unit is hot and ready, in just 30 seconds!
How do I charge my xmax V3 Pro?
XMAX V3 Pro Size and Portability You can pick up a couple of extra batteries for those longer festivals, group sessions, or just plain heavy use. You can charge them via USB-C inside the unit or pick up an external battery charger to top them off while still using the vaporizer.
How do you use MAX II?
One button, five lights Hold the power button for two seconds to engage the heater, which will automatically head for the last used temperature. Hold the button for two seconds to change the temperature. The light next to the chosen temperature will blink while heating, then turn solid when it's ready.
How do I use VLeaF go?
How To use your VLeaF GOLoosely load the chamber full of herb. ... Press the power button 5 times to turn it on or off.Adjust the temperature by pressing the button twice ( green = low, yellow = medium, red = high )Press and hold the button to take an on demand draw.For session mode, press the button three times.
How do you use V2 Pro Series 7 cartridges?
1:492:57V2 Pro Series 7 Vaporizer Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can adjust the temperature adjusting the temperature is easy you double-click the activationMoreYou can adjust the temperature adjusting the temperature is easy you double-click the activation button to initiate temperature.
What is a V2 Pro?
The V2 Pro Series 7 is a portable conduction vaporizer made by v2 cigs. They also make the V2 Pro Series 3 which is a smaller pen version of the S7. The V2 Pro S7 is a jack of all trades but master of none offering the ability to vape dry herbs and concentrates.
How do you use a vape Max?
How to use Max vape pen battery5 Clicks the button to turn ON/OFF.3 Clicks to adjust voltage: 2.7V – White, 3.1V – Blue, 3.6V – Red.2 Clicks to preheat (hold for 15 seconds)1 click to stop preheat.
Is there a dry vape?
Dry herb vape pens are very easy to use. Simply grind the herb – the finer, the better. Then fill the chamber on your vape pen and turn it on, which will heat the device and your material. Then, inhale and enjoy!
How do I use Max V3 Pro?
How to use the XMAX V3 ProMake sure your battery is fully charged before using.Remove the magnetic mouthpiece and load the chamber with up to 0.15 grams of flower.Don't pack your bud in too tightly or it will restrict the airflow.Press the power button three times to turn the device on.More items...•
How to burn off a vaporizer?
You won’t want material in there for the burn-off. Press your power button three times in a row to turn it on. The LED will flash and go blank. Hold the button to begin heating. Press the button down for 2 seconds to adjust the temperature. Set it to a max 428 degrees Fahrenheit and let it run. It will shut off automatically after a few minutes and you're good to go!
How long does it take for Xmax to charge?
The X-Max V2 Pro can be charged with the included Micro USB cable. Plug it into an AC adapter and let it charge up! The XMax V2 Pro takes about two hours to charge from empty to full.
How to turn on Xmax V2 Pro?
To turn it on, press the power button three times. This will put it in standby mode, indicated by the blinking lights. Hold the power button for two seconds to engage the heater, which will automatically head for the last used temperature. Hold the button for two seconds to change the temperature. The light next to the chosen temperature will blink while heating, then turn solid when it’s ready. It will turn off on its own after five minutes, but you can press the power button three times to turn it off manually.
How long does it take to charge Xmax V2 Pro?
We recommend charging the XMAX V2 Pro before you use it. This could take as long as four hours the first time, but will take less on subsequent charges. An external charger will charge your batteries a lot faster, but the USB port works fine. The white light will turn on to indicate the V2 Pro is charging, and will turn off when it’s fully charged.
How to fill a V2 Pro?
To fill your V2 Pro, remove the mouthpiece to expose the oven. Loosely fill the chamber, then lightly tamp it down so it doesn’t stick up too far. We recommend using the glass mouthpiece, as it does a better job cooling your vapor, so now would be a good time to switch.
What is the best way to clean a vape tank?
For that, you'll need alcohol-based solutions, vinegar, or special vape cleaners. Distilled water and vinegar, rubbing alcohol, and vodka are all preferred cleaning solutions.
How to clean a vape tank?
How to Clean Your Vape. Most vape instructions will guide you to submerge your vape tank and atomizer in water for a couple of hours. Some prescribe simply running the parts under warm water. Some even suggest dish soaps, yet that can leave a buildup so it's a risk not worth taking.
Why do you soak vape parts?
Minor Details. Soaking your vape parts on a regular basis will prevent things from getting too difficult to reach. The type of vape pen will determine your degree of difficulty. For instance, some pens have dedicated air holes to improve draw.
How to clean a battery in a microwave?
If you're going with a water and vinegar mixture, start by heating up a dish or bowl of distilled/filtered water in the microwave. Bring it to almost boiling, then mix in a few tablespoons of vinegar. Place all parts, besides the battery, in the solution and leave it to set for 20 minutes.
Do vape pens get dirty?
Vape pens themselves are becoming more flexible and robust with their capabilities. That is true as long as you know how to clean your vape. Eventually, you'll start to get weaker pulls and a muted flavor as your vape gets dirty. The first things that will fail you are the filters and the coils. You can save a lot of time ...
Can you get your coils wet?
If your coil is still viable, make sure to not get that wet! Don't forget to go over your filter and mouthpiece. Ideally, you should clean out these two parts on a daily basis, as they accumulate the most residue. If you soaked your parts in an alcohol, peroxide, or vodka solution, remember to rinse them off well.
How to fill a V2 Pro?
To fill your V2 Pro, remove the mouthpiece to expose the oven. Loosely fill the chamber, then lightly tamp it down so it doesn’t stick up too far. We recommend using the glass mouthpiece, as it does a better job cooling your vapor, so now would be a good time to switch.
How to turn on Xmax V2 Pro?
To turn it on, press the power button three times. This will put it in standby mode, indicated by the blinking lights. Hold the power button for two seconds to engage the heater, which will automatically head for the last used temperature. Hold the button for two seconds to change the temperature. The light next to the chosen temperature will blink while heating, then turn solid when it’s ready. It will turn off on its own after five minutes, but you can press the power button three times to turn it off manually.
How long does it take to charge Xmax V2 Pro?
We recommend charging the XMAX V2 Pro before you use it. This could take as long as four hours the first time, but will take less on subsequent charges. An external charger will charge your batteries a lot faster, but the USB port works fine. The white light will turn on to indicate the V2 Pro is charging, and will turn off when it’s fully charged.
What grind does the Xmax V2 Pro use?
The XMAX V2 Pro works best with a medium grind, like cracked pepper. Any grinder you might have available will be fine, or if you purchased a V2 Pro from Planet of the Vapes, the included grinder should be a great fit.
What does "clean Xmax starry" mean?
Our cleaning and maintenance guide will show you how to clean your XMAX Starry and have it looking brand new. A clean vaporizer means a happy vaporizer owner , and the XMAX Starry is no exception. When it’s clean, it’s easier to use, the vapor tastes better, and it’s more efficient.
How to disassemble Starry?
Start disassembling the Starry by removing the mouthpiece, and taking the metal screen from inside the oven. Pull the rubber gasket and ceramic screen from the bottom of the mouthpiece, and pop out the black ceramic screen inside. You can use the paper clip, or a similar poker, to remove the metal screen from inside the ceramic piece. You can disassemble the upper half by sliding the metal plate towards the center, which will release the mouthpiece stem. There’s a gasket on the stem that’s easy to lose, so watch out for it when the stem falls out.
Can you soak a vaporizer?
You should never soak, submerge, or wet the main vaporizer unit. All of the pieces from the mouthpiece should be soaked only in warm, soapy water. After a nice soak and a few good stirs, rinse everything in hot water until there’s no soap smell left, then dry everything completely.
Who is Brad Bourque?
brad bourque. Brad is a writer and tech nerd from Portland, Oregon, with a fondness for video games, craft beer, and the Portland Timbers. Find out which one is right for you as we compare these two portable favorites.
