What is the Joyetech ego AIO vape?
With the Joyetech eGo AIO, you can enjoy the perks of sub-ohm vaping – amazing vapor and enhanced flavor, etc. – without the hassle usually associated with it. In terms of vapor production, I am not exaggerating in any way when I say that the eGo AIO is on par with high-end mods operating in the 15W – 28W range.
Does the ego AIO contain nicotine?
WARNING: This product contains nicotine. Nicotine is an addictive chemical. Our products are restricted to adults 21+ only. eGo AIO, being all-in-one style, attaches the best anti-leaking structure with 2ml e-juice capacity.
How to charge ego AIO?
Simply charge eGo AIO by connecting it with a computer or a wall adapter (output: DC 5V) via USB cable. When it's fully charged, the button light will go out. eGo AIO presents you two forms of package: Standard kit and Easy package. The standard kit is a nice choice of gift for friends,
How big is the AIO vape?
At 118.5 mm in length and 19 mm in diameter, the AIO is slightly bulkier and heavier than the original eGo style e-cigs I used to vape on in my early days, but slimmer and lighter than the modern the Joyetech eGo One, not to mention any advanced mod I’ve ever used.
Why does the tip of my vape get hot?
Don't panic! Your vape getting hot is almost certainly nothing to worry about. Remember, vapes are specifically designed to manipulate heat: the battery supplies energy to the coil and the coil converts a part of that energy into heat, the result being a stream of vapour sent through the drip tip for you to inhale.
Why does my vape cartridge burning so fast?
High wattages Vaping at wattages that exceed the coil limits will vaporize e-liquid too fast. When that happens, the coils can burn the wicks, even when there's still some juice there. Always stay inside the recommended wattage ranges.
Is it normal for my vape to heat up?
It is normal for the atomizer to feel warm or hot to the touch. If however it is so hot that you are unable to touch it, you should start by checking the coil. An accumulation of gunk on the heating coil will produce a lot of heat and very little vapor.
How do I stop my vape from getting hot?
Install an Insulator Between the Tank and the Mod The most common insulator for vaping is polyether ether ketone (PEEK). If you can find one, a PEEK spacer that fits between your tank and your vaping device can keep the heat from radiating to the device and battery.
Is vaping supposed to burn your throat?
Though it is very safe for consumption, it is known to cause some throat irritation when used in high concentration. To avoid a burning throat feeling when vaping, use an e-liquid with a lower PG and a higher Vegetable Glycerin (VG) content.
How do you not burn a cartridge?
Avoid Overheating THC Oil CartridgesTake shorter, smaller puffs - if you pull on the pen until the timeout (when the lights blink) you're increasing the THC oils heat exposure. ... Use low voltage settings (3V or less) - this will help ensure less power goes to your THC oil cartridge, preventing overheating.
Can my vape explode?
Although these incidents appear uncommon, vape fires and explosions are dangerous to the person using the vaping product and others around them. There may be added dangers, for example, if a vape battery catches fire or explodes near flammable gasses or liquids, such as oxygen, propane, or gasoline.
Why is my vape burning my throat?
Volatile Organic Compounds and Diacetyl. Vaping juices may contain volatile organic compounds or diacetyl, both of which are known to cause throat irritation. 10 If you are experiencing a sore throat, changing products or quitting vaping may help relieve your symptoms.
What happens if you put a vape in water?
When vaping water, water vapor is the ultimate result, nothing more! When smoking it in, water vapor tends to condense in the mouth. Since it is pretty hot, there are higher chances that it might damage the mouth, burn either the lips or tongue or both and may also burn the pharynx.
Why is my vape popping and burning me?
The Wattage Level Is Too Low Your wattage or voltage might be too low. Low wattage means your device can't heat the e-liquid into vapor quickly enough. The e-liquid overflows the tank, resulting in spitback and popping noises. You'll make the problem worse if you use an RTA with a loose airflow.
basak Full Member
Today I bought an Ego aio d22 just as a temporary back up until I get my supplies for Innokin Endura T20. What a messy device comparing to the T20! I am pretty sure I did the set up just as instructed, I even watched some videos before doing it. Yet the device is overheating even with a quick push/inhale.
Bonskibon Vaping Master Verified Member ECF Veteran
The .6 ohm coil is SS so it will deliver a warmer vape than the kanthal 1 or 1.5 ohm coil. I use 1.5. The .6 is to warm for me. Make sure your also putting ejuice in the coil itself before putting your tank together.
basak Full Member
I don't remember what the device comes with, but you can purchase the 1 or 1.5 coil and use them if you want.
basak Full Member
Thank you, tomorrow I'll ask the supplier if he has any.. I hope he does
Bonskibon Vaping Master Verified Member ECF Veteran
Hi! Unfortunately I can't do that This was an illegal shopping since e-cig is banned in Turkey. But the device is original, I checked it online. However I can still address the guy who sold it. I'll do it tomorrow..
redeuce Ultra Member Verified Member ECF Veteran
Open the air flow all the way. My son had the same prob. Turned out his air flow was all the way closed. It gagged him when closed.
redeuce Ultra Member Verified Member ECF Veteran
It's very confusing. The top has a child proof cap plus the air flow is on the top. Read the manual or google the air flow adjustment. His was unvapable with the air flow closed. You just turn the top and open the air flow.
How much liquid do you need to atomize a vape?
You will need to prime your atomizer with e liquid for it to get saturated before you start vaping, for this atomizer you need to drip 5-6 drops of e liquid directly down the small hole at the top of the atomizer itself.
How to keep atomizer from spinning?
Once you get the atomizer screwed onto the threads, the atomizer will just keep spinning the child-lock once it gets tightened to a certain degree, so at that point you need to push down on the child-lock ring on the top while simultaneously screwing the atomizer on tight.
Why is my vape pen blinking?
If you go to use the vape pen and the LED light is blinking while you are holding down the button, that is signaling one of two things - either your battery is dead OR it is not recognizing your atomizer. If you know that your device is definitely charged, check your coil.
What does the LED light on an AIO mean?
The little LED light inside your AIO is a lot more useful than you may think, there's actually a series of light sequences that signifies different warnings. If you notice, when you press the button the LED light comes on and when you release the button the light goes away then comes back on a second later.
Can you use a vape pen without an atomizer?
Some people are a fan of one or the other and some people can't notice a difference so just go ahead and try them both out to see how you like them. Your vape pen should come turned off without an atomizer installed, you will need to turn it on, install a primed atomizer and fill it up with e-liquid to begin vaping.
Can you put a vape pen under water?
If you we're using a very potent flavor feel free to use a damp paper towel instead, just make sure to not put the vape pen under water as it is not water proof. As long as you remember to clean your AIO occasionally and replace the atomizer regularly, you should be vaping happy for awhile.
spstc New Member
I just got the AIO and it worked fine at first. Now, after I turn it on and after the light blinks rapidly, the light blinks slowly for as long as I hold the fire button down. After releasing, the light comes on for about five seconds and then turns off. Press again and the slow blinks followed by steady light for five seconds repeats. User error?
Bonskibon Vaping Master Verified Member ECF Veteran
I just got the AIO and it worked fine at first. Now, after I turn it on and after the light blinks rapidly, the light blinks slowly for as long as I hold the fire button down. After releasing, the light comes on for about five seconds and then turns off. Press again and the slow blinks followed by steady light for five seconds repeats. User error?
Bonskibon Vaping Master Verified Member ECF Veteran
Sounds like it's working as it should unless I'm not understanding (which is very possible). I have a couple AIOs myself.
memeticengineone Super Member ECF Veteran
It's a piece of junk. The glass tank in mine shattered before I replaced the first coil and the fire button would stick like crazy. Easy to clog the af with pocket lint too. Would recommend another mod .
Gramdogg Ultra Member ECF Veteran
I just got the AIO and it worked fine at first. Now, after I turn it on and after the light blinks rapidly, the light blinks slowly for as long as I hold the fire button down. After releasing, the light comes on for about five seconds and then turns off. Press again and the slow blinks followed by steady light for five seconds repeats. User error?
PressPlayVape Mod Addict ECF Veteran
I have an AIO and the light staying on for a few seconds after each use is normal, it's just telling you the battery level, when it blinks it's getting low. If it's blinking 5 times instead of firing that usually means there's a short, you may need to check your coil to make sure it's screwed in correctly.
Frankdank New Member
My AIO is failing me. When I pull in for a drag it sounds like a runny nose. It's really clogged but I have taken it apart, cleaned it, and... nothing. So I downloaded ego's aio pdf manual, scrolled through it...no help. Anyone out there thats has had a similar experience or knows how to fix?
jcrazorson
so my ego aio isnt powering on or hitting anymore, not sure if the battery has any charge in it, seems nt since devive wont power on nor allow color change option.
Walt
Just read a post where the user found a reset button on the bottom of the thing and used a pen to press it. Per user, it fixed the problem. Sorry, no personal experience.